Manualios.com

Epson R1400 Assembly Instructions Manual

Epson R1400 Manual Online:

3.55, 1366 votes
Epson R1400 User Manual
Epson R1400 User Guide
Epson R1400 Online Manual

Text of Epson R1400 User Guide:

  • Epson R1400, 1 IMPORTANT If your printer is new, set it up according to the enclosed manufacturers instructions. This is a check to ensure your new printer and drivers are working correctly before the Eco-Flo System is installed. ECO-FLO CONTINUOUS INK SYSTEM PermaJet Assembly Instructions for :R1400 Ink System It is very important you read these instructions carefully before you begin! We will take you throu

  • Epson R1400, 2 Check List for Components ____________________________________________________________________________________________ Set of 6 125ml Inks Injector Set & Tubes Bottle Caps & Clear Pi p in g Tube Support Bracket Bottle Holder Tray Special Injector Lid Pair of Latex Gloves Tube Clip With Adhesive Pad 6 Tube Clam p s 6 Empty 100ml Bottles 10ml Syringe Wing Adaptor Set of 2 Chip Blocks Set of Three Chip Su

  • Epson R1400, 3 Check Printer Condition If you have a brand new printer, follow the Epson instructions for setting up your printer. Use the Epson cartridges that came with the printer. Follow normal installation instructions for the software. Test the printer by printing pictures. Learn how to use the Epson utilities to run a Nozzle pattern check and to run a Cleaning Cycle. If you have been using the printer in the past, just make sure it produces a perfect nozzle pattern before proceeding with the Eco-Flo installation. If the Nozzle pattern

  • Epson R1400, 4 INSTALLATION OF YOUR ECO-FLO KIT Step 1 Removing the Injector Lid You will need to remove the printer lid on the injector carrier as shown illustrated from the diagrams below. Store this somewhere safe should you ever wish to return the printer to its original setup. The lid is held in place by two ‘Lugs’ on either side, once you have the LEFT side disconnected, the second lug can ONLY be removed by using a sharp Stanley knife type and scoring the plastic within the head as illustrated in Fig.3.

  • Epson R1400, 5 Step 2 Moving the Printer Head You are now able to move the printer head manually to the centre area of the printer. See below. Step 3 Bottle Preparation Locate the coloured bottle caps and straight lengths of plastic tubes. Insert the straight tube firmly into the bottom of each bottle cap see Fig.7 below. Step 4 Tube Preparation Fig.6 Fig.7

  • 6 Step 4 Tube Preparation Using a pair of scissors snip gently at the end of each tube. Please see Fig.8 below. Strip back all the tubes by approx 150mm. Please note when assembling the tubes to the bottle caps you may need to strip back more of the tubing in order for the bottles to be seated correctly within the

  • Epson R1400, 7 Step 5 Preparation of The Clamps & Inks You are now ready to attach the tube clamps to the tubes as indicated in Fig.11 below. Now please fill all the bottles with the correct inks; please ensure that all ink has been filled correctly as indicated by the bottle caps that are colour coded, see Fig.12 below. Step 6 Positioning the Ink Bottles in The Tray You are now ready to position the ink bottles in the bottle holder tray as indicated below on the LEFT hand side on the same level as the printer.

  • Epson R1400, 8 Step 7 Assembling the Tubing to the Bottle Caps When you have completed the above process insert the correct tubes to the correct ink bottles. PLEASE TAKE CARE when doing this as if this is connected incorrectly there is no turning back see Fig.13 & Fig.14 Step 8 Priming the Ink Through the Injectors You are now ready to start the ink priming process starting with the YELLOW. This process is carried out by inserting the 10ml syringe and wing adaptor at

  • Epson R1400, 9 PLEASE ENSURE THAT THE WING ADAPTOR (TIP ONLY) IS GENTLY, BUT MAKES A FIRM SEAL ON THE BASE OF THE INJECTOR, DO NOT push the tip into the injector as this shall split the base of the injector see Fig.16. PLEASE ENSURE that you DOUBLE CHECK that the correct tube is located to the correct ink bottle before pulling back on the syringe (see Fig.17), you may need assistance by another person for the next stage. At this point LOCK the tube with the white clamp (see Fig.18) before removing the syringe from the bottom base of the injector to avoi

  • Epson R1400, 10 Step 9 Installing the Chip Block Unit You are now in a position to remove the Epson cartridges from the printer head, see Fig.20 & Fig.21 below. Ensure that you hold the Colour chip block as indicated in Fig.22 and do not touch the contacts as this can cause damage or failure. Ensure that you locate the CORRECT chip block making sure that the two legs either side are facing down as indicated in Fig. 22. PLEASE NOTE INSERTING THE CHIP BLOCK INCORRECTLY CAN CAUSE DAMAGE TO THE CONTACTS.

  • Epson R1400, 11 Step 10 Installing the Chip Support Bars When you have positioned the chip blocks into place you will need to insert and install the support bars as indicated the correct way up (Arrow up) as illustrated in Fig. 24. Please ensure that you insert the bars as illustrated in Fig.25 making sure that the Groove is on the far end. Groove Insert the bar as illustrated making sure that this is pushed firmly into place see Fig.26, repeat this for the other side and the ot

  • Epson R1400, 12 Step 11 Install Injectors Please place the set of 6 injectors in the printer carriage that is now parked in the centre of the printer. Carefully align them, and when you are happy the injectors are in position. PLEASE BE CAREFUL NOT TO PUSH TOO HARD, AS THIS WILL CAUSE DAMAGE TO THE INJECTOR & PRINTER HEAD. Push the injectors home until you feel a positive seated position, see Fig.28 below. When all are in, they should look like Fig.29 below. Step 12 Fixing the Special Prin

  • 13 Align and locate the SLOT in the R1400 printer head as indicated in Fig.32. When you have installed the special printer lid on the R1400 it should finish and look like Fig.33 with the tubes moulded in that position. Slot within the printer head Step 13 Unlocking the Tube Clamps Please ensure that you UNLOCK the white tube clamps on all the tub

  • 14 Step 14 Installing the Central Tube Support Bracket & Aligning the Tubes The Tube Support Bracket has Self Adhesive Strips on it. Use an alcohol or cleaning solution and clean the top of the printer housing where the Tube Support Bracket is going to be attached, see Fig.36. Then make sure the area is dry before proceeding. Remove the adhesive backing off bo

  • Epson R1400, 15 Please ensure that the tubing has just enough slack which may need to be adjusted to allow movement of the print head without restriction. This can be done manually by moving the head to the left and right and checking that there is just enough tubing to allow the print head to move freely from left to right, see Fig.39 below. Step 15 Install Final Tube Clip The last tube clip goes on the left edge of the printer housing see Fig.40 below. Clean this area with alcohol and wipe dry with

  • Epson R1400, 16 When you have carefully installed and aligned the tube clip in its correct location, press firmly ensuring that the tube clip is clicked and stuck down to the printer body, as illustrated in Fig.42 below. Step 16 Installing the Foam Strip The purpose of the Foam Strip is to ensure that the tubing on the Eco-Flo travels under the printer body correctly, as well as to cushion the tubes from hitting the printer casing when in motion. Move the head manually across to the left Peel back the yellow sticky tape ready for installation and bend back the Fo

  • Epson R1400, 17 43mm Position the Foam Strip in its correct location as When you have placed the right hand side of indicated in Fig.45, You MUST align the Foam Strip the Foam Strip, very carefully bend it back to the flush to the edge ensuring that you lightly tack white point as illustrated in Fig.46. the right hand side onto the casing. Now ensure that you lightly tack down the Please move the head manually across ensuring bottom halve of the

  • Epson R1400, 18 Step 17 Testing the System Push the injectors to the far right and plug the printer back on. Have your graphics program (e.g. Photoshop) open and ready to use. The printer should come on and the head should move back and forth a few times and do a cleaning cycle. When it stops moving, only the green light should be on. A red light at this point indicates that one of the chips has not been recognized or seated correctly. If this is the case please push firmly on the Chip block that is

  • Epson R1400, 19 Step 18 Removing the Injectors Please note before removing the injectors you MUST clamp the tubing on the relevant injectors by LOCKING the White tube clamps to avoid air traveling up the injector and into the tube. At this point press the ink change button on the front panel of the printer so that you are ready to change or remove the injectors, this function will bring the head unit to the left. Locking the tube

  • Epson R1400, 20 ON THE COMPACT DISC :- THERE IS A CD SUPPLIED WITH YOUR KIT. ON THE CD ARE COPIES OF THE FOLLOWING :- 1 ECO-FLO INSTALLATION INSTRUCTIONS FOR ALL TYPES OF PRINTERS AND SYSTEMS 2 TROUBLE SHOOTING GUIDE 3 INK PURGE TEST FILES AND TONE CHARTS 4 ICC PROFILES FOR USE WITH PERMAJET COLOUR INK AND PAPER COMBINATIONS 5 CURVES FOR USE WITH MONOCHROMEPRO INK SYSTEM. IN ORDER TO USE THE PERMAJET INK SYSTEM TO ITS FULL POTENTIAL, YOU SHOULD NOW TAKE THE TIME TO OPEN THE ENCLOSED CD AND PROCEED TO READ THE FULL SECTION ON PROFILES AND THE “HOW TO INS

  • 21 FAQ»S & Caring For Your Eco-Flo √ READ CAREFULLY!!! Here are some tips to make sure that your new system performs trouble-free. • It is advised to gently shake by rotation each ink bottle on a regular weekly basis. This is to ensure the XL (Xtra Life) Dye inks stay suspended in solution and gives constant results. • After printing,

Related Products and Documents (Printer):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 NAD T557 Owner's manual nad/t557-ZON.pdf 09 Jun 2023 28
2 Silicon Laboratories TOOLSTICK EK Operation & user’s manual silicon-laboratories/toolstick-ek-89N.pdf 29 Dec 2022 8 0.38 Mb
3 Python 594 Owner's manual python/594-52U.pdf 15 May 2023 69
4 Frigidaire FRA054XT70 Use & care manual frigidaire/fra054xt70-9T3.pdf 04 May 2023 10
5 Audiovox DVD Home Theater System Owner's manual audiovox/dvd-home-theater-system-J7W.pdf 11 Oct 2023 41 1.57 Mb
6 Snapper S211, SP211, SPV211, SPV211S, Safety instructions & operator's manual snapper/s211-sp211-spv211-spv211s-573.pdf 09 Mar 2024 28

Similar Resources:

  • Xerox

    Phaser 540

    (79 pages)
    Release NotePhaser ™ CopyStationUser Manual Copyright © 1994 by Tektronix, Inc., Wilsonville, Oregon. Printed in the United States of America.All rights reserved. Contents of this publication may not be reproduced in any form withoutpermission of Tektronix, Inc.December 1994 Part Number 070-9020-80 …
  • Xerox

    8860MFP - Phaser Color Solid Ink

    (2 pages)
    environmental benefitsSolid InkBring green into your office schemewith the Xerox Phaser® 8860MFP and Phaser® 8860 printerThe Xerox solid ink imaging process is the most environmentally friendly way to put an image on paper. From its nearly waste-free printing process to its safe, toxin-free solid ink sticks, it was made withthe earth in mind.Leaves no trac …
  • CognitiveTPG

    A799

    (4 pages)
    A799 Two-Color Thermal Receipt Printer Setup GuideThank you for selecting TPG Model A799 Two-Color Single Station Thermal POS Receipt PrinterSTRENGTH... ENDURANCE... SPEED!You have chosen the world’s most innovative thermal receipt printer. A799 features ultra fast printing, industry-leading durability and outstanding graphics capability.Please review this …
  • MakerBot

    Replicator 2

    (3 pages)
    MakerBot Replicator 2 Thermocouple Replacement InstructionsBefore you begin, do the following: • Unload any filament.• Turn off the MakerBot Replicator 2.• Remove the filament guide tube and spool holder.• Unplug power and USB cables.1. Detach the active cooling duct.Gently pull the active cooling duct away from the nozzle. Allow the duct to hang. 2. …
  • Paxar

    9855 RFID

    (24 pages)
    QuickReferenceQuickReferenceMonarch9855 RFIDPrinter®®TC9855RFIDQR Rev. AN 4/08 ©2007 Paxar Americas, Inc. a subsidiary of Avery Dennison Corp. All rights reserved. …
  • Lexmark

    B2650

    (318 pages)
    B2650, M3250, MS621, andMS622 printers4600-830, -835, -895Service Manual• Start diagnostics• Maintenance• Safety and notices• Trademarks• IndexNovember 16, 2018 www.lexmark.com …

Comments, Questions and Opinions: