Manualios.com

KIP 7100 Operation & User’s Manual

KIP 7100 Manual Online:

4.35, 2238 votes
KIP 7100 User Manual
KIP 7100 User Guide
KIP 7100 Online Manual

Text of KIP 7100 User Guide:

  • KIP 7100, Chapter 4 Maintenance 4-2 4. 1 Cleaning 4. 1. 1 Scanner Unit It is recommended to clean each Scan Glass, Feeding Rollers and Guide Plates as the scan/copy image may become defective if these parts are dirty. 1. Turn off KIP 7100. 2. Press the levers (1) up to unlock the Scanner Unit. Open the Scanner Unit. 3. Wipe each Scan Glass (2), Press Rollers (3) and the inside surface with a soft cloth. Use equal volume mixture of water and a neutral detergent.

  • KIP 7100, Chapter 1 Before Use 1-7 Subject Specification Media source 2 Roll Decks Manual Feeder (single cut sheet) Paper Tray (multiple cut sheet, option) Media (Recommended Media) US model: Bond 64g/m 2 to 80g/m 2 , US Bond (PB-20) Vellum US Vellum (XV-20) Film 4MIL (PF-4DDME) Europe/Asia model: Plain Paper 64g/m 2 to 80g/m 2 , Oce Red Label (75g/m 2 ) Tracing Paper Oce Transparent Paper (80g/m 2 ) Film Oce 3.5MIL Storage of consumables (Toner cartridge) Store the cartridge within the temperature range from 0 to 35 degrees Centigrade and within the humidity range

  • KIP 7100, Chapter 1 Before Use 1-16 1. 7. 3 Treatment against environmental condition Take a necessary treatment according to the environmental condition as shown below. Humidity(%) Possible problem Necessary treatment “Void of image”, “crease of paper” and other problems occurs when you print with plain paper and tracing paper. 1. Install the humidifier in the room, and humidify the room air. 2. Remove the paper from the machine right after the completion of print, and keep it in a polyethylene bag. “Void of image” occurs when you print with tracing paper. If you will not make print s

  • Chapter 3 Error Correction 3-8 5. Pull and remove the jammed print to the rear. If you remove the print at this time, just close the Exit Cover. If the print cannot be removed, go to the next step. 6. Hold the white handle (4) and release the Fuser Door (5). Pull and remove the jammed print to the rear.

  • KIP 7100, Chapter 2 Basic Operation 2-16 2. 6 Copying 1. There are several size markings on Original Table which indicate possible feed positions. Line up Original Guides (1) with the proper markings according to the original width. 2. Place the original on the Original Table with face up . Then insert it under the Scanner Unit along with Original Guides (1). When the leading edge touches the original feeding roller, the machine automatically carries and sets the original at the proper position. 3. The KIP 7100 will start

  • KIP 7100, (5) POWER CORD INSTRUCTION The installation of (or exchange to) a power plug which fits in the wall outlet of the installation location shall be conducted in accordance with the following: WARNING Select a power plug which meets the following criteria; - The plug has a voltage and current rating appropriate for the product’s rating marked on its name plate. - The plug meets regulatory requirements for the area. - The plug is provided with a grounding pin or terminal. If the appropriate plug does not fit the wall outlet in the installation, the customer shall install an appropriate outlet. Connector Typ

  • Chapter 3 Error Correction 3-9 7. Close Fuser Door (5) and Exit Cover (3). 8. Gently close the Engine Unit. 9. Replace Print Trays in the original position. NOTE Be sure to close the Engine Unit firmly until it locks at the correct position. 5 3

  • Chapter 2 Basic Operation 2-9 7. Insert the leading edge of the roll media under Guide Plate (8) until it touches the feeding roller. Rotate Feed Knob (9) clockwise so that the feeding rollers catch the leading edge. 8. Hold the green grip (11: on the middle of Guide Plate) and turn Guide

  • KIP 7100, Chapter 1 Before Use 1-6 1. 4. 2 Printer part Subject Specification Printing method LED Array Electro photography Photoreceptor Organic Photoconductive Drum Print speed 80mm per second (Inch) 3.4ppm/E 5.8ppm/D Landscape (Metric) 3.3ppm/A0 5.6ppm/A1 Landscape Print head LED Array Resolution of print head 600dpi x 600dpi Print width Maximum 914mm / 36” Minimum or 297mm / 11” (roll media) or 210mm / 8.5” (cut sheet) Print length Maximum (Standard) 6,000mm / 19.7ft for 36” / A0 wide (plain paper / bond) or “5 x

  • KIP 7100, Chapter 3 Error Correction 3-6 3. 1. 3 Reg. Jam / Internal Jam 1. Remove Print Trays (1). 2. Pull up the Engine Unit Open Levers (1) to open the Engine Unit. 3. Remove the mis-fed paper. 4. Gently close the Engine Unit. 5. Replace Print Trays in the original position. NOTE Be sure to close the Engine Unit firmly until it locks at the correct position. 1 1 1 1 mis-fed media

  • KIP 7100, Chapter 1 Before Use 1-4 1. 3 Features (1) The KIP 7100 is a single footprint Multi-Function Printer which can copy, scan and print. Advanced drivers and comprehensive print utilities make the KIP 7100 an advanced, easy to use system. (some functions may be optional) (2) KIP HDP technology generates no waste toner. (3) The combination of the KIP HDP Plus imaging system with mono-component minute toner produces high definition lines, distinctive greyscale and consistent blacks. (4) The maximum paper width is 36” (914mm) wide, and the

  • KIP 7100, Chapter 1 Before Use 1-15 Pre-printed Extremely slippery Extremely sticky Extremely thin and soft OHP Film 1. 7. 2 Keeping the paper in the custody Keep the paper in the custody taking care of the following matters. 1. Do not expose the paper to the direct sunlight. 2. Keep the paper away from high humidity. (It must be less than 70%) 3. Put the paper on a flat place 4. If you will keep the p

  • KIP 7100, (4) CAUTION There are hot items inside of the printer. Take great care not to touch these items when you remove mis-fed media. Do not pull the cord when you unplug the printer as you may damage the Power Cord. Do not install the printer in a humidified room or a dusty room. Also, do not install the printer on an unstable floor as injuries may occur. 1. Unplug the printer before you

  • KIP 7100, Chapter 2 Basic Operation 2-7 4. Insert each Flange (2) into both ends of the roll media core to be installed. 5. Push both the levers (4) down in either way. Position them flat against Flange to secure the roll media. NOTE (1) Fully insert Flange into the roll media core so that the inside rim of Flange evenly touches the side face of the roll media. Correct: Fully inserted Wrong: not touching roll side (2) Flange has Sto

  • KIP 7100, Chapter 2 Basic Operation 2-10 9. Slide the green Cutter Knob (12) fully from one side to the other to make a new straight edge. Remove the cut portion. 10. Gently close Roll Deck. NOTE Completely slide Cutter Knob (12) until it stops at either end. Not doing so may cause a paper jam. Correct Wrong NOTE Be sure to close the Roll Deck fully until it locks at the correct position. A paper jam may occur if it is not locked firmly. 12 12 12

  • KIP 7100, Chapter 2 Basic Operation 2-18 2. 7 Emergency Stop of Scan or Copy 1. If necessary, press the Emergency Stop Button (1) on the Scanner Unit to immediately stop the original while making a copy or scan. Pressing the button stops the current reading a document immediately. The current printing is stopped as well and is ejected. NOTE Do not pull back or hold down the original on Original Table as an attempt to stop feeding it through

  • KIP 7100, Chapter 3 Error Correction 3-5 3. 1. 2 Manual Jam 1. Remove Print Trays (1). 2. Pull up the Engine Unit Open Levers (2) to open the Engine Unit. 3. Remove the mis-fed paper pulling frontward. 4. Gently close the Engine Unit. 5. Replace Print Trays in the original position. NOTE (1) Be sure to close the Engine Unit firmly until it locks at the correct position. (2) The mis-feed cut sheet should be replaced with a new one if its leading edge has a torn or fold. Or it should be used upside down to keep the damaged edge from been inserted.

  • Chapter 1 Before Use 1-3 1. 2 Originals Prohibited from Duplication It is not necessarily allowed to copy every kind of original. You may be punished by the law if only you possess the copy of some kind of original. We recommend you to consider enough before you copy such original. [Originals prohibited from copying by the law] 1. It is not allowed to copy

  • KIP 7100, Chapter 2 Basic Operation 2-17 The KIP 7100 has the ability to eject prints / copies to the printer’s top tray (standard) / rear stacking equipment (option). For the top tray, the printer will inform you of “Tray Full” on exceeding capacity of stacking. If the UI screen shows “Tray Full”, remove all the prints on the top tray. For further information of switching top / rear ejection, see KIP IPS Touch screen Operator’s Guide.

More Instructions:

DOWNLOAD

Related Products and Documents (All in One Printer):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 KitchenAid KCMC155J Dimension manual kitchenaid/kcmc155j-RL6.pdf 05 Jan 2023 1
2 Nortel Media Dependent Adapters 302403-G Installation manual nortel/media-dependent-adapters-302403-g-AE1.pdf 25 Nov 2022 32
3 Trotec IDS 100 Operation manual trotec/ids-100-A6I.pdf 06 Jan 2024 12
4 Philips FC8038/01 Operation & user’s manual philips/fc8038-01-853.pdf 27 Sep 2022 2
5 Hitachi 24HXJ15U Instruction manual hitachi/24hxj15u-938.pdf 31 Dec 2023 45
6 Fortinet FortiBridge FortiBridge-1000F Quick start manual fortinet/fortibridge-fortibridge-1000f-MS3.pdf 26 Dec 2023 2 0.2 Mb

Similar Resources:

  • Kyocera

    KM-6330

    (97 pages)
    KM-6330 Printer OptionOperation Guide<Functions Edition>IntroductionChapter 1 Printer-related operation■ 1. Operation Keys■ 2. Procedure for Making Settings■ 3. Menu Flow Chart■ 4. Selecting the Printer Settings■ 5. OptionsChapter 2 Software-related operation■ 1. Procedure for Installing and Printingwith a Printer Driver■ 2. Windows KX …
  • Xerox

    PHASER 6121MFP

    (4 pages)
    X_13741_61EBR-01EA LANGUAGE: ENGLISH FREEDMAN INT. NO: 13741 PROOF NO: 01 PLATES: CMYK+ PANTONE 158 C DATE: 09-06-2009 PAGE 1Phaser®6121MFP A4Colour LaserMultifunction PrinterXerox® Phaser® 6121MFP Colour Laser Multifunction PrinterSimplify. Streamline. Customise. …
  • Konica Minolta

    bizhub 225i

    (32 pages)
    ! ! 1Shortcut Manual簡易說明書 …
  • Lexmark

    X 2650

    (2 pages)
    Convenient and Versatile.Ready for Home & School.l Up to 22 ppm black and 16 ppm colour printing (2)l Fast and easy install in as little as ten minutes!l Borderless prints up to A4 or 8½ x 11"Fast and easy install in as little as 10 MINUTESl 1-touch copy and scanHome & StudentX2650 3-in-1Print. Copy. Scan. …
  • Canon

    F-1

    (179 pages)
    654321Duplex Color Image Reader - F1Service ManualApril 11, 2013Revision 0Product OutlineTechnologyPeriodic ServicingParts Replacing and CleaningAdjustmentsInstallationAppendix …
  • Lexmark

    C792 Family

    (141 pages)
    Document Distributor 4.5Administrator's GuideAugust 2010 www.lexmark.comLexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.All other trademarks are the property of their respective owners.© 2010 Lexmark International, Inc.All rights reserved.740 West New Circle R …

Comments, Questions and Opinions: