Manualios.com

IBM 102 Operation & User’s Manual

IBM 102 Manual Online:

3, 2766 votes
IBM 102 User Manual
IBM 102 User Guide
IBM 102 Online Manual

Text of IBM 102 User Guide:

  • IBM 102, 8. To be sure you have installed the ribbon cartridge correctly, check that: a. The left side of the ribbon cartridge is securely snapped onto the printer. The right side fits over the ribbon drive post but does not latch down. b. There are no twists or folds in the ribbon. c. The ribbon is not catching on the print head. d. The ribbon moves when you turn the blue ribbon advance knob clockwise. If the ribbon does not move, replace the ribbon cartridge. Blue Ribbon Advance Knob Chapter 1. Setting Up the 4230 Printer 1-9

  • Unit Check Indicator The Unit Check indicator has two operating conditions: Off The printer has not detected any printer errors. Blinking The printer has detected a printer error. The alarm beeps (if not disabled). If the printer also displays a status code, go to “Using the Status Code and Problem Listings” on page B-2. Operator Panel Keys The operator panel has the foll

  • IBM 102, Power Switch The power switch supplies electricity to the printer. It has two positions: On (|) and Off (O). Power Switch Notes: 1. When you turn the power On (|), a power-on test runs. For the description of the power-on test, see “Power-On Test” on page 3-4. 2. Always wait 10 seconds after turning the power from Off (O) to On (|). 3. Anytime you turn the power On (|), you should verify the top of form position before running a job. See Chapter 1, “Setting Up the 4230 Printer” for adjusting the top of form position for your forms device. Warning: If you turn the power Off (O) while data is in the printer buffer (a temporary storage area) or coming f

  • IBM 102, To manually configure a remote 4230 Printer, use the parameters given in the following table. Refer to the appropriate documentation for the remote control unit that you are using. The printer can be configured to an IBM 5294, 5394, or 5494 Remote Control Unit. Type your choices and press Enter. Parameter Description Parameter Parameter Setting Device description DEVD Workstation printer name Device class DEVCLS *RMT Device type TYPE *IPDS Device model MODEL 0000 Advanced Function AFP *NO (See Note) Location Address LOCADR xx Onl

  • Power-On Test Whenever you turn the power On (|), a power-on test runs. An error-free power-on test goes through these steps: 1. All indicators light briefly. 2. The alarm beeps. 3. Two rows of boxes fill the display. 4. The printer displays the following messages 5. The print head and ribbon move. You will hear some sounds from these movements. If no p

  • IBM 102, Loading Forms in the F3 Forms Device To load forms in the F3 forms device, follow these steps: 1. Adjust for the width of the form. Hold a form in front of the upper forms guide and against the left stop. Unlock the blue locking lever and move the right roller assembly so that the pointer lines up with the right edge of the form. Blue Locking Lever Left Stop Left Stop Upper Forms Guide Pointer Right Roller Assembly If needed, use the white writing surface near the blue sliding guides to ma

  • IBM 102, 11. Compare your printout with the sample printout. Did the lines print and is the remainder of the printout clear and readable? If YES, go to Step 12. If NO, do the following: a. If any of the following items are not installed correctly, the printer can experience forms jamming, ribbon jamming, or an incorrect printer verification printout: Forms device Ribbon cartridge Forms. Repeat the Setup Instructions from page 1-6 if you suspect a ribbon, forms, or forms device installation problem. b. Press Enter or Start, load another form, and press Load/Eject to get another printout. c. If the second printout is still not similar to the sample printout, go to Appendix B, �

  • Using the Printer Verification Test for the F2 Forms Device To run the printer verification test, follow these steps: 1. Turn the power On (|) if not already on. 2. Wait until the printer displays 3. Press Stop. The printer displays and then on Models 102, 1I1, and 4I3 you may see or on Models 202, 2I1, and 5I3 you may see While on Models 4I3 and 5I3 (when parallel or serial is the active in

  • IBM 102, Preparing for Forms Device Installation To prepare for installing the forms device, follow these steps: CAUTION: The construction of this machine provides extra protection against the risk of electric shock by grounding appropriate metal parts. The extra protection may not function unless the power cord is connected to a properly grounded outlet. This machine has a grounding-type (3-wire) power cord because grounding is necessary. It is the responsibility of the customer or the person installing the machine to connect it to a properly grounded outlet. Se

  • 4. If the default value does not give the best print sample, press Scroll or Scroll until the printer displays the same number of arrows that were printed beside the best print sample line. Press Enter to set this as the new default value. The printer then prints another line to demonstrate the new default value, and the test is complete. or Press Stop to end the test without c

  • Automatic Forms Thickness Adjustment (AFTA) The Automatic Forms Thickness Adjustment (AFTA) mechanism performs the following tasks: Automatically measures the forms thickness and adjusts the gap from the print head to the platen rod based on the measured value. Measures the form thickness whenever printing is to occur. When you replace the paper, the thickness is automatically re

  • IBM 102, Notices References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program, or service is not intended to state or imply that only IBM's product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any of the intellectual property rights of IBM may be used instead of the IBM product, program, or service. The evaluation and verification of operation in conjunction with other products, except those expressly designated by IBM, are the responsibility of the user.

  • IBM 102, 4. Turn the power On (|). Note: Do not turn the printer power Off (O) during setup unless instructed to do so. The printer does the following: a. All indicators and blocks on the display light, and the alarm beeps. Then the printer displays The printer then displays b. The print head and ribbon move. c. The printer displays and then followed by The Attention indicator also blinks and the alarm beeps. This status code appears because forms have not been loaded. DIAGNOSTICS IN PROGRESS <A> Calibrating Printer <A> Please Wait DIAGNOSTICS COMPLETE <A> 1 END OF FORMS LOAD FORMS 1-14 User’s Guide

  • IBM 102, Appendix D. Declaration of IBM Product Noise Emission Values The following tables show the noise emission values for the 4230 Printer. Notes: 1. LWAd is the declared sound power emission level for a production series of machines. 2. <LpA>m is the mean value of the space-averaged sound pressure emission levels at the one-meter positions for a production series of machines. All measurements are made in accordance with the American National Standards Institute (ANSI) S12.10 and reported in conformance with the International Organization

  • IBM 102, The printer also prints a single line of H’s. 4. If the H’s do not start where you want your left margin, press Scroll or Scroll until the printer displays the desired value for the left margin position. For each change in value, the left margin is changed 0.686 mm (0.027 in.). 5. Press Enter. An asterisk ( * ) appears in front of the selected value. The forms advance one line and the row of H’s prints again. This value is now the current left margin position. 6. Repeat Steps 4 and 5 until the left margin is correctly aligned. (You can press Line Feed o

  • IBM 102, Problem: Ribbon smudging forms 1: The Automatic Forms Thickness Adjustment (AFTA) setting needs to be changed. Solution: See the procedure for adjusting the forms thickness setting through the operator panel (based on your forms device) in Chapter 1, “Setting Up the 4230 Printer.” 2: The ribbon cartridge is defective. Solution: Replace the ribbon cartridge. See Chapter 4, “Replacing Your Ribbon.” 3: The ribbon is twisted. Solution: Remove the ribbon, straighten it, and reinstall it (see Chapter 4, “Replacing Your Ribbon”). 4: The ribbon is over-inked. Solution: Replace the ribbon. See Chapter 4, “Replacing Your Ribbon.” Problem: Pr

  • IBM 102, 3. Locate the gears on the forms device and turn them while checking for noticeable binds. For the F1 and F2 forms devices, check that the tractor pins move when you turn the gear. For the F2, F3, and F4 forms devices, be sure that the feed rolls also move when you turn the gear. If manually turning the gears or rollers does not fix the problem, go to the next step. 4. If you see damage to the device, if the gears or rollers continue to bind, or if the device still does not operate properly, call for service. Dual Purpose Forms Device (F2) (All Models) Gears Tractor Pins Right Roller Assembly Left Roller Assembly Feed Rolls Tractor Pins Gear Contin

  • IBM 102, Models 102, 1I1, and 4I3 Twinaxial Attachment Supported computers include: System/36 Application System/400* (AS/400*) 5294 and 5394 Remote Control Units. Attaching a Twinaxial Signal Cable to the Printer To attach a twinaxial cable (not shipped with the printer), follow these steps: 1. Set the address. If your desired printer address is 0, go to Step 3 on page 2-4. If your desired printer address is not 0, see the following table for the valid values and follow Steps 1a on page 2-3 through 1g on page 2-4 to change the value. If you do not know what to assign for the printer address, check with

  • IBM 102, S serial cable, attaching a 2-23 serial number 3-2 settings, printer 3-16 setup, printer check out ribbon cartridge installation 1-9 F1 (Continuous Forms Device) check out F1 forms device installation 1-23 install the 1-21 load forms in the F1 forms device 1-26 prepare to load F1 forms 1-24 print verification test for the F1 forms device 1-33 F2 (Dual Purpose Forms Device) check out F2 forms device installation 1-58 install the 1-55 load forms in the F2 forms device 1-60 prepare to load F2 forms 1-59 print verification test for the F2

  • IBM 102, 2. Unlock the right blue locking lever and move the right tractor assembly to the extreme right. Blue Sliding Guides Blue Locking Lever Bottom Metal Bar Right Tractor Assembly Top of Forms Device Tear Bar 3. Lower the forms device into the printer behind the platen rod. Be sure that F2 is in the upper left corner facing you and the blue tractor doors at the bottom of the device enter the printer first. Align the ends of the device with the slots in the frame. Continue to lower the device until the ends of the device rest in the slots of the fr

  • IBM 102, Unloading Forms To unload forms from the F2 forms device, follow these steps: 1. Open the acoustic cover. 2. Tear off the forms at the tear bar. See “Adjusting the Tear-off Position” on page 1-79 for the procedure. 3. Press Stop. The printer displays 4. Open the front paper door as follows: a. Pull the door up until it will not go any higher. b. Push the door back slightly to lock it in the open position. Paper Door NOT READY <A> 1-84 User’s Guide

  • IBM 102, Auto Sheet Feeder (F4): 1. Press Stop. 2. Place paper in the manual bin. 3. Press Load. 4. Press Start. Continuous Forms Device (F1) and Dual Purpose Forms Device (F2): 1. Press Stop. 2. Load forms. 3. Be sure that the forms are loaded correctly and that they are under the blue forms guide/forms sensor. 4. Be sure that nothing blocks the blue forms guide/forms sensor. 5. Reset the top of form position. 6. Press Start. 7. Verify the printed output; if data loss is suspected, follow local operating procedures. Document Insertion Device (F3): 1. Press Stop. 2. Press Load/Eject. 3. Load the correct form size, or 4. Check the maximum page length s

  • IBM 102, Adjusting the Print Alignment You can adjust dot registration and print quality for characters created using bidirectional printing. The bidirectional alignment may need periodic adjustment to maintain print quality. To change the bidirectional alignment, follow these steps: 1. If the printer is ready, press Stop. The printer displays 2. Press Test. The printer displays 3. Press Scroll or Scroll until the printer displays 4. Press Enter or Start to print this test. The Ready indicator goes on and printing begins. The test prints samples using alignment values higher and lower than the default value. The print sample using the default value is ind

  • IBM 102, 3. Use the following figures to learn the location of keys and indicators on the operator panel. Figure 1-1, Figure 1-2, Figure 1-3 on page 1-13, and Figure 1-4 on page 1-13 show the operator panel for each model. Load/ Eject Display Address Form Feed Start Set Top of Form Stop Cancel Print Line Feed Hex Print Micro Micro Darker Lighter Quick Menu Test Scroll Scroll Enter Return Power Ready Processing Online Attention Unit Check Figure 1-1. 4230 Printer Models 102 and 1I1 Operator Panel Menu Load/ Eject Form Feed Start Set Top of Form Stop Cancel Print Test Scroll Scroll Mic

  • IBM 102, form, detecting the last form feed past it, and detecting paper jams. forms tension knob. Blue knob used to adjust the setting on the forms tension lever on the F1 forms device. forms tension lever. Used to control the tension on paper loaded in the F1 forms device. Settings range from * (no tension) to 6 (maximum tension). F1. See Continuous Forms Device. F2. See Dual Purpose Forms Device. F3. See Document Insertion Device. F4. See Auto Sheet Feeder. I Intelligent Printer Data Stream* (IPDS). An architected host-to-printer data stream that contains both data and controls defining how the data is to

  • IBM 102, A C D Pos. 1 B 132 Positions at 10 CPI 158 Positions at 12 CPI 198 Positions at 15 CPI 220 Positions at 16.7 CPI | Figure C-3. Form Design Considerations - Cut Forms (Models 102, 1I1, | 202, and 2I1) C-12 User’s Guide

Related Products and Documents (Printer):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Mercedes-Benz Comand MY11 Operating instructions manual mercedes-benz/comand-my11-R57.pdf 20 Nov 2023 190
2 Philips 220E1SB1 Specifications philips/220e1sb1-9H7.pdf 28 Aug 2023 2
3 Ryobi RPT4545E Original instructions manual ryobi/rpt4545e-98E.pdf 26 Dec 2022 61
4 Cisco Cisco Unified IP Phone 7960G Phone manual cisco/cisco-unified-ip-phone-7960g-JB1.pdf 26 Jul 2022 60 2.86 Mb
5 Karcher HD 6/13-4 M Operation & user’s manual karcher/hd-6-13-4-m-ABJ.pdf 12 Aug 2022 11
6 Frigidaire ATFB6000ES1 Operating instructions manual frigidaire/atfb6000es1-2S2.pdf 18 Oct 2023 6 0.17 Mb

Similar Resources:

  • Tektronix

    Phaser 360

    (292 pages)
    Service ManualPhaser ® 360Color Printer WarningThe following servicing instructions are for use by qualified service personnel only. To avoid personal injury, do not perform any servicing other than that contained inoperating instructions unless you are qualified to do so.This printing: 10-27 1997070-9923-00 …
  • Lexmark

    MX710 Series

    (3 pages)
    FTP guideYou scan documents directly from the printer to an FTP server.Note: You can scan to only one FTP address at a time.Scanning to an FTP address using the printer control panel1 Load an original document faceup, short edge first into the ADF tray or facedown on the scanner glass.Notes:• Do not load postcards, photos, small items, transparencies, phot …
  • Epson

    Artisan 1430

    (12 pages)
    NoticesImportant Safety InstructionsBefore using your Epson product, read and follow these safety instructions:■ Be sure to follow all warnings and instructions marked on the product.■ Use only the type of power source indicated on the product’s label.■ Use only the power cord that comes with the product. Use of another cord may cause fires or shock. …
  • TallyGenicom

    9050N -

    (2 pages)
    Mono9050N Mono LaserPower Printing9050N laser printer delivers powerful performance at up to 50 pages per minute and exceptional imagequality of 1200 dpi resolution. Additional features like private printing and web-based job accountingprovide added security and accountability to the printing system.The 9050N is available with up to six input trays to hold a …
  • Lexmark

    CS410 series

    (10 pages)
    Quick ReferenceLearning about the printerUsing the printer control panel31248769105Use the To1 Display• View the printer status.• Set up and operate the printer.2 Select button• Select menu options.• Save settings.3 Arrow buttons Scroll through menus, or settings on thedisplay.4 Keypad Enter numbers, letters, or symbols.5 Sleep button Enable Sleep mo …
  • Ricoh

    Aficio SP 8200DN

    (16 pages)
    1InformationIntroductionThis manual contains detailed instructions and notes on the operation and useof this machine. For your safety and benefit, read this manual carefully beforeusing the machine. Keep this manual in a handy place for quick reference.ImportantContents of this manual are subject to change without prior notice. In no eventwill the company be …

Comments, Questions and Opinions: