Manualios.com

Ericsson HM200c/HM201c Operation & User’s Manual

  • HM200c/HM201c Network Card
  • maV4UWn5/ulTE
  • Operation & User’s Manual
  • PDF / Adobe Acrobat Reader
  • 38

Ericsson HM200c/HM201c Manual Online:

4.2, 2987 votes
Ericsson HM200c/HM201c User Manual
Ericsson HM200c/HM201c User Guide
Ericsson HM200c/HM201c Online Manual

Text of Ericsson HM200c/HM201c User Guide:

  • Ericsson HM200c/HM201c, PipeRider® Cable Modem User's Guide HM200c/HM201c FAQs What is the PipeRider cable modem? How do I get started? How do I access the Internet with the PipeRider cable modem? Can I talk on the telephone while using the PipeRider cable modem? Can I watch cable TV while using the PipeRider cable modem? With the connection to the Internet always on, I’m concerned about hackers getting into my computer. What’s the difference between an Ethernet connection and a USB connection? Can I connect more than one computer to the PipeRider cable modem? If I buy a new computer or change operating systems, will the PipeRider cable modem still work? What spec

  • Ericsson HM200c/HM201c, IP See Internet Protocol IP Address A unique, 32-bit address assigned to every device in a network. An IP address is composed of a network address and a host address. Each network is assigned an address by a government agency, and each company administrator assigns an address to each host computer. ISP See Internet Service Provider LED See Light Emitting Diode Light Emitting Diode A light emitting diode (LED) is a semiconductor device that emits light when voltage is applied between its terminals. MAC See Media Access Control MAC Address The physical address of the Media Access Control d

  • Ericsson HM200c/HM201c, PipeRider® Cable Modem User's Guide HM200c/HM201c PipeRider Cable Modem Product Specifications HM 200c DOCSIS Cable Modem HM 201c Euro-DOCSIS Cable Modem Downstream Frequency Range 91-858 MHz 112-858 MHz Bandwidth 6 MHz 8 MHz Modulation 64-QAM or 256-QAM 64-QAM or 256-QAM Bit Rate 25 Mbps (64-QAM), 43 Mbps (256-QAM) 41.7 Mbps (64-QAM), 55.6 Mbps (256-QAM) Forward Error Correction ITU J.83-B per DOCSIS RFI Sec. 4.3.2. ITU-T J.83-Annex A Signal Levels -15dBmV to +15dBmV 43 dBµV to 73 dBµV (64-QAM), 47 dBµV to 77 dBµV (256-QAM) Upstream Frequency Range 5-42

  • Ericsson HM200c/HM201c, PipeRider® Cable Modem User's Guide HM200c/HM201c PipeLock® The PipeLock® feature enables you to suspend communication between the Internet and your computer with the touch of a button. This provides added security when the cable modem is not in use. When PipeLock is ON, the PipeRider cable modem remains logged on, but direct communication between your computer and your service provider is blocked. Since PipeLock doesn’t interrupt communication between the cable modem and the service provider network, a second touch of the button instantly restores communication. To turn PipeLock ON, simply press the PipeLock button located on the top

  • Ericsson HM200c/HM201c, PipeRider® Cable Modem User's Guide HM200c/HM201c Warranty ONE YEAR LIMITED WARRANTY Ericsson Inc. ("the Company") warrants this hardware product, and the Company provided software contained therein ("Product"), against defects in materials and workmanship at the time of purchase or lease and for a period of one year from its original purchase or lease by the end-user. If, during the warranty period, Ericsson receives notice of the above defined defects under normal use and service, Ericsson will at its option, either repair or replace the Product in accordance with the terms

  • Ericsson HM200c/HM201c, Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. European Union Suppliers' Declaration of Conformity We, ERICSSON HomeCom, hereby claim sole responsibility for and declare that the product listed below, to which this Suppliers' Declaration of Conformity relates, is in conformity with the following EC Directives, Product Standards, and other Normative Documents listed below, and follows the provisions of: Radio & Telecommunication Terminal Equipment (R&TTE) Directive No. 1999/05/EC Electromagnetic Comp

  • Ericsson HM200c/HM201c, PipeRider® Cable Modem User's Guide HM200c/HM201c Installation: Ethernet for Macintosh To connect the PipeRider cable modem to your Macintosh computer through an Ethernet port, your computer must be equipped with a Network Interface Card (NIC) and configured for TCP/IP protocol. Ethernet Setup The following procedures are provided to assist you in verifying that your Ethernet port is configured for TCP/IP protocol. Select the Apple menu and then select Control Panels >> TCP/IP. The TCP/IP window will appear.1. In the Configure list, Using DHCP Server should be selected.2.

  • Ericsson HM200c/HM201c, PipeRider® Cable Modem User's Guide HM200c/HM201c Contact Your Service Provider Step 1: Verify that your local Service Provider supports two-way cable modem access To enjoy the speed of the PipeRider cable modem, your local Service Provider must support two-way cable modem access. Two-way access allows data to flow in both the upstream and downstream directions. Since the PipeRider cable modem sends and receives data over the Service Provider's cable line, the PipeRider will not operate in a one-way (downstream only) cable modem configu

  • PipeRider® Cable Modem User's Guide HM200c/HM201c PipeRider LEDs Looking at the top of the PipeRider cable modem, you’ll see five amber-colored light-emitting diodes (LEDs) along the left side of the unit. These LEDs indicate the current state of the cable modem and provide useful diagnostic information. Although the functions of the LEDs depend u

  • Ericsson HM200c/HM201c, PipeRider® Cable Modem User's Guide HM200c/HM201c Cable Network The cable that provides service to your PipeRider cable modem is connected to the same cable network system that brings cable TV service to your home. A simplified version of the cable system is depicted below. Click on the diagram for a description of each of the main system components. Headend The Headend can be thought of as the control center of the system. The Cable TV (CATV) equipment receives signals from sources such as satellite and broadcast transmissions. These signals are p

  • PipeRider® Cable Modem User's Guide HM200c/HM201c Materials and System Requirements Materials Needed In addition to the items packaged with your cable modem, you may need some of the materials below to install your modem: A standard coaxial cable is required to connect the PipeRider cable modem to the cable jack in your house. The length of the cable is determine

  • Ericsson HM200c/HM201c, PipeRider® Cable Modem User's Guide HM200c/HM201c Wall Mounting Procedure Step 1. The PipeRider cable modem can be mounted on the wall using two screws and the two mounting slots on the bottom of the unit. When mounted, the orientation of the cable modem will be as shown below. Step 2. Use the template below to mark the screw locations. 10 cm Step 3. Insert and secure screws to the wall. The screws should not be secured flush to the wall. Leave a gap of approximately 0.6 cm from the wall surface to the bottom of the screw head. Step 4. Slip the PipeRi

  • PipeRider® Cable Modem User's Guide HM200c/HM201c Features and Benefits In addition to the benefits provided by cable modem technology itself -- such as speed, instant Internet access, and the support of multiple computers -- the PipeRider cable modem offers even more features to make your life easier. Installation Ease and Adaptability You have t

  • Ericsson HM200c/HM201c, PipeRider® Cable Modem User's Guide HM200c/HM201c Operational States There are a number of different operational states that the PipeRider cable modem may pass through. Each of these states and its associated LEDs are described below. Power-Up, Initialization, and Normal Operation In the Power-up Diagnostics state, the cable modem executes diagnostics to verify the integrity of the hardware and software. This state is entered when the modem is first powered up, after a power cycle, or after a user reset. When power-up diagnostics begin, all of the LEDs turn ON briefly. This allows you to verify that all LEDs are functioning properly. The Power LED remains ON and the re

  • Ericsson HM200c/HM201c, PipeRider® Cable Modem User's Guide HM200c/HM201c Computer Interface to Cable Modem There are two data-interface options for connecting the PipeRider cable modem to your computer: a USB connection and an Ethernet connection. For details regarding cable modem installation using either of these interfaces, please refer to the Installation section of this CD. The Universal Serial Bus (USB) connection requires that your computer is equipped with a USB port, and that you are using one of the operating systems listed on the System Requirements list. To link the computer to the cable modem using a USB interfac

  • Ericsson HM200c/HM201c, TCP/IP Transmission Control Protocol/Internet Protocol (TCP/IP) is the most commonly used protocol suite for the Internet, which combines TCP and IP. Transmission Control Protocol Transmission Control Protocol (TCP) is a standard that provides transmission control for applications to ensure reliable delivery of data despite changing network conditions. TCP is the transport layer portion of TCP/IP. Trunk Cable The main cable that carries signals in and out of the Service Provider building. Two-Way Cable Modem Access Cable access that allows data to flow in both the upstream and downstream

  • Ericsson HM200c/HM201c, PipeRider® Cable Modem User's Guide HM200c/HM201c End-User License Agreement © Ericsson Inc. 1999-2001- All rights reserved Hardware Product. PipeRider® Cable Modem and PipeLock® Locking Feature. PipeRider® and PipeLock® are trademarks or registered trademarks of Ericsson Inc. IMPORTANT - READ CAREFULLY: This End-User License Agreement ("Agreement") is a legal contract between you (either an individual or a single business entity) and Ericsson Inc ("Licensor"), for the software contained both on the Compact Disk (CD) and within the hardware product identified above, which includes computer soft

  • PipeRider® Cable Modem User's Guide HM200c/HM201c PipeRider Stand Mounting Procedure Step 1 Insert a stand post into each of the U-shaped grooves in the stand base. Each post will snap when secured in place. Step 2 Align and insert latches on each post with slots on bottom of cable modem. Slide modem down to lock in place.

  • Ericsson HM200c/HM201c, PipeRider® Cable Modem User's Guide HM200c/HM201c Operation Once the PipeRider cable modem has been properly installed and connected, simply open your Internet browser and you are instantly on-line. No logon procedures are necessary. The cable modem operates automatically and will rarely, if ever, require any intervention from you. The PipeRider cable modem can be left on at all times. There's no need to turn it on and off, since the PipeLock® feature assures your security when you are not using the Internet. To take full advantage of your cable modem, you should also acquaint yourself with the PipeRider LEDs,

  • Ericsson HM200c/HM201c, PipeRider® Cable Modem User's Guide HM200c/HM201c PipeRider Introduction The PipeRider® cable modem will open a whole new world of Internet use for you. Once you try it, you’ll wonder how you ever got along without it! Using your PipeRider cable modem to communicate with the Internet provides you with many features and benefits that usher you into the 21st century in style … including speed, security, instant access, multimedia capability, and much more. How can it do all this? In short, the PipeRider cable modem allows

  • Ericsson HM200c/HM201c, LVD Safety LVD Safety Test Report(s) CB Certificate No. US/3799A/UL 99NK36432-120899 Australia and New Zealand This device has been tested in accordance to and found in compliance with the following standards. AS/NZS 3548: 1995 Class B ● AS/NZS 3260: 1993 + Supp. 1: 1996● ACA TS 001-1997● Japan This device has been tested in accordance to and found in compliance with the following standards. VCCI V-3: 1997 Class B ● Taiwan This device has been tested in accordance to and found in compliance with the following standards. CNS 13438 (C6357): 1997 Class B ● International This device has been tested in accordance to and found in c

Related Products and Documents (Network Card):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Briggs & Stratton 074045 Instruction manual briggs-stratton/074045-214.pdf 16 Jun 2023 20
2 Frontgate 154855 Assembly instructions frontgate/154855-JNM.pdf 22 Aug 2022 3
3 Link electronic Analog White Clip Video DigiFlex 1151 Specification sheet link-electronic/analog-white-clip-video-digiflex-1151-K35.pdf 17 Jan 2023 2
4 Blomberg DUS 2040 Instruction booklet blomberg/dus-2040-L1D.pdf 25 Dec 2022 28 1.52 Mb
5 Troy-Bilt TB6044 XP Operator's manual troy-bilt/tb6044-xp-9A8.pdf 10 Sep 2023 40 6.07 Mb
6 Hunter 28079 Manual de usuario hunter/28079-6YF.pdf 24 Feb 2024 14

Similar Resources:

  • Panasonic

    MA2SD300G

    (4 pages)
    Schottky Barrier Diodes (SBD)1Publication date: October 2007 SKH00181AEDThis product complies with the RoHS Directive (EU 2002/95/EC).MA2SD300GSilicon epitaxial planar typeFor super high speed switching■ Features• Small reverse current: IR < 2 µA (at VR = 30 V)• Optimum for high frequency rectification because of its shortreverse recovery time trr …
  • Dell

    8

    (88 pages)
    Dell™ PowerEdge™M1000e, M910, M905, M805,M710HD, M710, M610x, M610,M605, and M600Getting StartedWith Your SystemGuide de mise en routePrimeiros passos com o sistema Procedimientos iniciales con el sistema …
  • Agilent Technologies

    Agilent 4396B

    (179 pages)
    Agilent4396B Network/Spectrum/ImpedanceAnalyzerGPIB ProgrammingGuideSERIALNUMBERSThismanualappliesdirectlytoinstrumentswithserialnumberprexJP1KE.Foradditionalimportantinformationaboutserialnumbers,read\SerialNumber"inAppendixA.Agilent Part No. 04396-90063Printed in Japan May 2003Sixth Edition …
  • Sanyo

    PJ-Net

    (114 pages)
    OWNER’S MANUALThis PJ-Net Organizer is an optional network productfor the projector. Mount this product to the projectorand connect a network cable. It enables a projector todisplay the image data stored in the file server and thescreen image of the computer via the network. In addi-tion, you can control and set up the projector remotelyby using the web br …
  • HP

    4710s - ProBook - Core 2 Duo 2.53 GHz

    (4 pages)
    The HP ProBook 4710s Notebook PC letsyou think big and work big at a price you’llappreciate.Technology to get the job doneThe HP ProBook 4710s Notebook PC boastsa sleek design that packs an array offeatures normally reserved for moreexpensive notebooks. Available in a newglossy Noir finish with a more spaciouskeyboard layout and separate numerickeypad, it …
  • Tascam

    FW-1082

    (2 pages)
    11/12/04Page 1 of 2Cubase LEHow To Install Cubase LE with your TASCAM Computer InterfaceSteinberg’s Cubase LE is now included with these TASCAM computer interfaces: the US-122, US-224, US-428, FW-1082, FW-1804 and FW-1884. This guide should help you set up your TASCAM interface with your comput-er and set up Cubase LE so that it communicates with the inter …

Comments, Questions and Opinions: