Cisco SPA942 - - IP Phone Administration Manual

Text of Cisco SPA942 - - IP Phone User Guide:

• Cisco SPA942 - - IP Phone, SPA and Wireless IP Phone Field Reference Phone Tab Cisco SPA and Wireless IP Phone Administration Guide 245 B Ring Tone (SPA9X2/SPA525G) Each entry defines a ring tone to be used on the phone, with an ID between 1 and 10. The ID can be used in a DirEntry to indicate which ring tone to use when the corresponding caller calls. Parameter Description Ring1 Ring tone script for ring 1. Defaults to n=Classic- 1;w=3;c=1. Ring2 Ring tone script for ring 2. Defaults to n=Classic- 2;w=3;c=2. Ring3 Ring tone script for ring 3.

• Cisco SPA942 - - IP Phone, SPA and Wireless IP Phone Field Reference Regional Tab Cisco SPA and Wireless IP Phone Administration Guide 217 B • Language (SPA525G only), page 230 • Miscellaneous, page 231 Call Progress Tones Parameter Description Dial Tone Prompts the user to enter a phone number. Defaults to 350@-19,440@-19;10(*/0/1+2). Bluetooth Dial Tone (SPA525G only) Ton e that indicates a bluetooth headset is on and the user can make a call. Defaults to 350@-19,440@-19;1(0/*/0);10(*/0/1+2). Outside Dial Tone Alternative to the Dial Tone. It prompts the user to enter an external phone number, as opposed to a

• Cisco SPA942 - - IP Phone, SPA and Wireless IP Phone Field Reference System Tab Cisco SPA and Wireless IP Phone Administration Guide 198 B Internet Connection Type and Static IP Settings SPA525-protocol (SPA525G only) Allows you to choose the type of protocol for the phone: • SIP—Session Initiation Protocol. Choose if the phone is used with a SIP call control system, such as the SPA9000 or a SIP call control system from another provider such as BroadSoft or Asterisk. • SPCP—Smart Phone Control Protocol. Choose if the phone is used with a Cisco Unified Communications Se

• Cisco SPA942 - - IP Phone, Configuring Security, Quality, and Network Features Ensuring Voice Quality 122 Cisco SPA and Wireless IP Phone Administration Guide 6 as they arrive. This reserve is known as a jitter buffer. The bigger the jitter buffer, the more jitter it can absorb, but this also introduces bigger delay. Jitter buffer size should be kept to a relatively small size whenever possible. If jitter buffer size is too small, many late packets may be considered as lost and thus lowers the voice quality. Cisco IP phones dynamically adjust the size of the jitter buffer according to the network conditions that exist during a call. The minimum jitter buffer size is 30

• Cisco SPA942 - - IP Phone, Customizing Cisco SPA and Wireless IP Phones Configuring Phone Information and Display Settings Cisco SPA and Wireless IP Phone Administration Guide 53 4 STEP 3 Click the Phone tab. STEP 4 In the General section, in the Screen Saver Enable field, choose yes. STEP 5 In the Screen Saver Wait field, enter the number of seconds of idle time to elapse before the screen saver starts. STEP 6 In the Screen Saver Icon field, choose the display type: • A background picture. • The station time in the middle of the screen. • A moving padlock icon. When the phone is locked, the status line displays a scrolling message “Press any key to unlock

• Cisco SPA942 - - IP Phone, SPA and Wireless IP Phone Field Reference Info Tab Cisco SPA and Wireless IP Phone Administration Guide 191 B Info Tab This section describes the fields for the following headings on the Info tab: • Product Information, page 193 • Phone Status, page 193 System Information NOTE: The fields on this tab are read-only and cannot be edited. Parameter Description DHCP Indicates if DHCP is enabled. Displays Enabled on SPA901, DHCP on other phones. NOTE Not applicable to SPA525G or WIP310. Connection Type (WIP310/ SPA525G only) Indicates the type of internet connection for the phone: • DHCP • Static IP • PPPoE (not applicabl

• Cisco SPA942 - - IP Phone, Creating an LED Script Cisco SPA and Wireless IP Phone Administration Guide 189 A • Remote Seized: This call appearance has been seized by another station to prepare for an outbound call • Remote Progressing: Another station is making a call on this call appearance and is progressing • Remote Active: Another station is engaged in a connected call on this call appearance • Remote Ringing: Another station is ringing for an incoming call to this call appearance • Remote Held: Another station has placed this call appearance on hold • Remot

• SPA and Wireless IP Phone Field Reference User Tab Cisco SPA and Wireless IP Phone Administration Guide 267 B Call Forward See Vertical Service Activation Codes, page 221 for more information on call forwarding parameters. Speed Dial Speed Dial 2 through 9: Target phone number (or URL) assigned to speed dial 2, 3, 4, 5, 6, 7, 8, or 9. Defaults to blank. NOTE Speed dial configu

• Configuring SIP, SPCP, and NAT Configuring SIP Cisco SPA and Wireless IP Phone Administration Guide 99 5 To configure SDP payload types: STEP 1 Log in to the web administration interface. STEP 2 Click Admin Login and advanced. STEP 3 Click the SIP tab. STEP 4 Under SDP Payload Types, configure the fields shown in the following table and click Submit All Changes. Param

• Cisco SPA942 - - IP Phone, Configuring SIP, SPCP, and NAT Configuring SPCP on the SPA525G Cisco SPA and Wireless IP Phone Administration Guide 109 5 Configuring SPCP on the SPA525G The SPA525G can be used as part of a Cisco Unified Communications System. This system uses SPCP (also called SCCP) for call control features. To configure SPCP on the SPA525G: STEP 1 Log in to the web administration interface. STEP 2 Click Admin Login and advanced. STEP 3 Click the System tab. STEP 4 Under System Configuration, in the SPA525

• SPA and Wireless IP Phone Field Reference SIP Tab Cisco SPA and Wireless IP Phone Administration Guide 210 B RTCP Tx Interval Interval for sending out RTCP sender reports on an active connection. It can range from 0 to 255 seconds. During an active connection, the SPA9000 can be programmed to send out compound RTCP packet on the connection. Each compound RTP packet exc

• Cisco SPA942 - - IP Phone, SPA and Wireless IP Phone Field Reference Regional Tab Cisco SPA and Wireless IP Phone Administration Guide 232 B Daylight Saving Time Rule Enter the rule for calculating daylight saving time; it should include the start, end, and save values. This rule is comprised of three fields. Each field is separated by ; (a semicolon) as shown below. Optional values inside [ ] (the brackets) are assumed to be 0 if they are not specified. Midnight is represented by 0:0:0 of the given date. This is the format of the rule: Start = <start-time>; end=<end-time>; save = <save-time>. The <start-time> and <end-time>

• Cisco SPA942 - - IP Phone, 4 Cisco SPA and Wireless IP Phone Administration Guide 47 Customizing Cisco SPA and Wireless IP Phones This chapter describes customizing the SPA and Wireless IP phones and contains the following sections: • Configuring Phone Information and Display Settings, page 47 • Enabling Call Features, page 56 • Configuring Phone Features, page 65 • Enabling SMS Messaging, page 74 • Enabling the Web Server, page 76 • Configuring Lightweight Directory Access Protocol (LDAP), page 77 • Configuring BroadSoft Settings (SPA525G), page 81 • Configuring Music On Hold, page 8

• Cisco SPA942 - - IP Phone, SPA and Wireless IP Phone Field Reference Regional Tab Cisco SPA and Wireless IP Phone Administration Guide 228 B Force G722 Code Makes this codec the only codec that can be used for the associated call. Defaults to *02722. NOTE SPA525G only. Only one G.722 call at a time is allowed. If a conference call is placed, a SIP re-invite message is sent to switch the calls to narrowband audio. Prefer L16 Code Makes this codec the only codec that can be used for the associated call. Defaults to *01016. Force L16 Code Makes this codec the only codec that can be used for the associated call. Defaults to *02016.

• Cisco SPA942 - - IP Phone, Configuring SIP, SPCP, and NAT Configuring SIP 92 Cisco SPA and Wireless IP Phone Administration Guide 5 CTI Enable If set to yes, enables the computer telephony integration (CTI), where a computer can act as a call center handling all sorts of incoming and outgoing communications., including phone calls, faxes, and text messages. The CTI interface allows a third-party application to control and monitor the state of a Cisco IP phone and, for example, initiate or answer a call by clicking a mouse on a PC, NOTE: CTI must be enabled on the SPA962 for an attached SPA932 to properly monitor the SP

• Cisco SPA942 - - IP Phone, Getting Started Viewing Phone Information Cisco SPA and Wireless IP Phone Administration Guide 31 2 Viewing Phone Information After you log on to the web UI (see “Using the Web Administration User Interface” section on page 25), you can check the current status of a the SPA or Wireless IP Phone by clicking the Info tab (appears by default). The Info tab shows information about all phone extensions, including phone statistics and the registration status. All fields are read-only. See “Info Tab” section on page 191 for more information abou

• Cisco SPA942 - - IP Phone, Configuring Lines and Extensions Configuring Lines Cisco SPA and Wireless IP Phone Administration Guide 37 3 STEP 7 Click Submit All Changes. Assigning Busy Lamp Field, Call Pickup, and Speed Dial Functions to Unused Lines on a SPA525G, SPA962 or SPA942 You can configure unused or idle lines on a SPA525G, SPA962 or SPA942 to interact with another phone line in the system. For example, if you have two idle lines on an assistant’s phone, you can configure those lines to show the status of

• SPA and Wireless IP Phone Field Reference Phone Tab Cisco SPA and Wireless IP Phone Administration Guide 241 B Line Key LED Pattern NOTE Does not apply to the WIP310. SCA Barge-In Enable Enables the SCA Barge-In. Defaults to no. Parameter Description Parameter Description Idle LED LED pattern during the Idle state, where the call appearance is not is in use and is available

• Cisco SPA942 - - IP Phone, SPA and Wireless IP Phone Field Reference SIP Tab Cisco SPA and Wireless IP Phone Administration Guide 202 B SIP Tab This section describes the fields for the following headings on the SIP tab: • SIP Parameters, page 202 • SIP Timer Values (sec), page 205 • Response Status Code Handling, page 208 • RTP Parameters, page 209 • SDP Payload Types, page 211 • NAT Support Parameters, page 214 • Linksys Key System Parameters, page 216 SIP Parameters Parameter Description Max Forward SIP Max Forward value, which can range from 1 to 255. Def

• Cisco SPA942 - - IP Phone, Contents Cisco SPA and Wireless IP Phone Administration Guide 5 IP Phone Configuration Profiles 136 General Purpose Parameters 137 Sample Configuration File 138 Upgrading, Resyncing, and Rebooting Phones 138 Firmware Upgrade Parameters 140 Resyncing a Phone 141 Rebooting a Phone 142 Redundant Provisioning Servers 142 Retail Provisioning 143 Automatic In-House Preprovisioning 143 Configuration Access Control 144 Using HTTPS 145 Server Certificates 145 Client Certificates 145 Obtaining a Server Certificate 146 Chapter 8: Configuring Regional Parameters and Supplementary Services 147 Advanced Scripting f

• Cisco SPA942 - - IP Phone, Configuring Regional Parameters and Supplementary Services Using a Dial Plan 162 Cisco SPA and Wireless IP Administration Phone Guide 8 If the phone is part of a SPA9000 system, you create a dial plan for the system that is then propagated to the individual phones. In certain cases, you must configure the dial plan on individual phones: • If the phone is outside the SPA9000 multicast domain (e.g. when the phone is connected to the SPA9000 via a VPN connection). • For additional extensions on an existing phone (the system wide phone dial plan is propagated only to extension 1 of all phones). F

• Cisco SPA942 - - IP Phone, Configuring the SPA932 Attendant Console Setting Up the SPA932 Attendant Console 178 Cisco SPA and Wireless IP Phone Administration Guide 9 In the following example, extension 3500 is used to add Subscribecontext to point to the context. This is entered in the file sip.conf: [3500] type=friend secret=3500 callerid="spa3500"<3500> nat=no context=home mailbox=3500 Subscribecontext=home ... ... Configuring the SPA932 Complete the configuration required for the extensions on your IP PBX and obtain the following information: • SPA9000 IP address or other hostname • Phone extension numb

More Instructions:

	Cisco SPA942 - - IP Phone Operation & user’s manual 02-01-2024 55	DOWNLOAD
	Cisco SPA942 - - IP Phone Operation & user’s manual 21-03-2023 87	DOWNLOAD

Related Products and Documents (Switch):

Comparable Devices:

Similar Resources:

• Bdcom S1518-16P-330 (13 pages) R 专 业 网 络 科 技 Gigabit PoE Switch S1510-8P-150/S1518-16P-330/S1526-24P-400 Gigabit Uplink PoE Switch S1210-8P-150/S1218-16P-330/S1226-24P-330User Guide …

• ANTAIRA LNX-800AG-E Series (23 pages) LNX-800AG-E Series8-Port Industrial Gigabit Unmanaged Ethernet Switch, with 8*10/100/1000Tx Ports,12~48VDC Power Input, E-mark VersionHardware ManualVersion 1.0(September 2021) …

• D-Link DSN-5410-10 - xStack Storage Area Network Array Hard Drive (160 pages) D-Link xStack Storage iSCSI SAN Arrays Managed SAN Solutions DSN-5000 Series (DSN-5110-10, 5210-10, 5410-10, 5000-10) Management Center Software User’s Guide Version 1.3 …

• White Rodgers 770-1 (4 pages) Type 770-1 Air SwitchWith SPDT Switch Action(Responds to Positive, Negative, or Differential Pressure)INSTALLATION INSTRUCTIONSFAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE.DESCRIPTION The Type 770-1 has an SPDT switch that can be actu-ated by a positive p …

• LCN 8310-2300 Series (5 pages) Models 8310-2310, -2320, -2330, -2340 Installation InstructionsDescriptionAvailable faceplates: L Note: A minimum depth of 2-3/4” for all box installations, and mortised holes when not using a box, is recommended.8310-2310 (Single Gang): 2-3/4” x 4-1/2” stainless steel, fits on single gang electrical boxes.8310-2320 (Double Gang): 4-1/2” x 4-1/2” …

• Quintum Tenor AX (78 pages) Tenor AX ®VoIP MultiPath/Gateway Switch Product Guide P/N 480-0062-00-14 Tenor and Quintum are registered trademarks. PacketSaver, Quintum Technologies, Inc., Risk Free VoIP, VoIP Made Easy, SelectNet, and SelectNet Technology are trademarks of Quintum Technologies, Inc. This unit contains new hardware, which requires newer software. This software was …

Comments, Questions and Opinions: