Manualios.com

Marantz PD4220V Operation & User’s Manual

Marantz PD4220V Manual Online:

3, 1918 votes
Marantz PD4220V User Manual
Marantz PD4220V User Guide
Marantz PD4220V Online Manual

Text of Marantz PD4220V User Guide:

  • Marantz PD4220V, 35 Loop Out setting When this feature is set to ON, the received signal will be looped out. Example: Setting “ON” Set “ADVANCED OSM” to “ON” in the main menu (1/ 2), then perform the following operations. 1. On the MAIN MENU, select “OPTION3”, then press the MENU/ENTER button. The “OPTION3” screen appears. 2. Use the ▲ and ▼ buttons to select “LOOP OUT”. 3. To set the LOOP OUT to “ON”... Use the 䊴 and 䊳 buttons to select “ON”. The mode switches as follows each time the 䊴 or 䊳 button is pressed: OFF ↔ ON OPTION3 3 / 3 EXIT PREVIOUS PAGE TIMER PWR.

  • Pour éviter des dommages et prolonger la durée de service de l’appareil: 1. N’utiliser qu’une source d’alimentation de 120 V 50/ 60 Hz CA. Le fait d’utiliser l’appareil en continu à des tensions de ligne supérieures à 120 Volts CA réduit sa durée de vie et risque de provoquer un incendie. 2. Manipuler l’appareil avec soin pendant son déplacement et ne pas le faire tomb

  • Marantz PD4220V, 3 Rear View/ Terminal Board A AC IN Connect the included power cord here. B EXT SPEAKER L and R Connect speakers (optional) here. Maintain the correct polarity. Connect the (positive) speaker wire to the EXT SPEAKER terminal and the (negative) speaker wire to the EXT SPEAKER terminal on both LEFT and RIGHT channels. Please refer to your speaker’s owner’s manual. C VIDEO1, 2, 3 (BNC, RCA, S-Video) Connect VCR’s, DVD’s or Video Cameras, etc. here. VIDEO1 can be used for Input or Output (see pag

  • 13 Wide Screen Operation (manual) With this function, you can select one of six screen sizes. When viewing videos or digital video discs 1. Press the WIDE button on the remote control. 2. Within 3 seconds ... Press the WIDE button again. The screen size switches as follows: → NORMAL → FULL → STADIUM → ZOOM → 2.35:1 → 14:9 When a 720P or 1080I signal is input: FULL ↔ 2

  • Marantz PD4220V, 15 Menu Operations The OSM window is displayed with respect to the screen as shown on the diagram. * Depending on the screen’s mode, the OSM may be displayed differently. In the explanation, the OSM section is shown close up. MAIN MENU 1 / 2 MENU/ENTER EXIT PICTURE AUDIO IMAGE ADJUST OPTION1 ADVANCED OSM NEXT PAGE : OFF SEL. EXIT OK The following describes how to use the menus and the selected items. 1. Press the MENU/ENTER button on the remote control to display the MAIN MENU. MAIN MENU 1 / 2 ME

  • Marantz PD4220V, 31 Setting the picture size for RGB input signals Use this procedure to switch the setting to “ON” or “OFF”. Example: Setting the “PICTURE SIZE” mode to “OFF” Set “ADVANCED OSM” to “ON” in the main menu (1/ 2), then perform the following operations. 1. On the MAIN MENU, select “OPTION2”, then press the MENU/ENTER button. The “OPTION2” screen appears. 2. Use the ▲ and ▼ buttons to select “PICTURE SIZE”. 3. To set PICTURE SIZE mode to “OFF”... Use the 䊴 and 䊳 buttons to select

  • Marantz PD4220V, 1 50 mm (2") 50 mm (2") 50 mm (2") Wall Wall 50 mm (2") 50 mm (2") You can attach your optional mounts or stand to the plasma monitor in one of the following two ways: * While it is upright. (See Drawing A) * As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face. * Do not touch or hold the screen face when carrying the unit. • This device cannot be installed on its own. Be sure to use a stand or

  • Printed in Japan 02/2004 ECMar 38AW851022 7S900057 is a registered trademark. www.marantz.com You can find your nearest authorized distributor or dealer on our website. JAPAN Marantz Japan, Inc. 35-1 Sagami Ohno 7-Chome, Sagamihara-shi, Kanagawa 228-8505, Japan U.S.A. Marantz America, Inc. 1100 Maplewood Drive, Itasca, IL 60143, U.S.A. EUROPE Marantz Europe B.

  • Marantz PD4220V, 33 FUNCTION ............. Set the LONG LIFE function. 䡵 To reset the program Align the cursor with the DATE field that you wish to reset, then press the CLEAR button. 䡵 To reset the data Align the cursor with the field (ON/OFF/INPUT/ FUNCTION) that you wish to reset, then press the CLEAR button. 䡵 Special characters in the PROGRAM TIMER screen PROGRAM TIMER EXIT DATE MON TUE SAT *FRI — SAT * SEL. RETURN ADJ.ZOOM ON 08 : 30 - - : - - 08 : 30 08 : 30 - - : - - 08 : 30 15 : 30 OFF 10 : 30 18 : 15 12 : 15 10 : 00 - - : - - 12 : 15 16 : 00 INPUT RGB2 — VIDEO1 H

  • Marantz PD4220V, 28 ORBITER Use this to set the picture shift. Example: Setting “ORBITER” to “AUTO1” Perform Steps 1-2 of LONG LIFE, then... 3. Use the ▲ and ▼ buttons to select “ORBITER”. 4. Use the 䊴 and 䊳 buttons to select “AUTO1”. The mode switches as follows each time the 䊴 or 䊳 button is pressed: →OFF ↔ AUTO1 ↔ AUTO2 ↔ MANUAL← LONG LIFE EXIT PLE ORBITER INVERSE SCREEN WIPER SOFT FOCUS : AUTO : AUTO1 : OFF : OFF : OFF SEL. RETURN ADJ. Information 䡵 ORBITER settings OFF ..............Orbiter mode does not function. This is the default setting when RGB is input. AUTO1

  • Marantz PD4220V, Précautions Veuillez lire avec attention ce manuel avant d’utiliser le moniteur à plasma et le conserver accessible pour s’y référer ultérieurement. ATTENTION RISQUE D’ELECTROCUTION NE PAS OUVRIR MISE EN GARDE: AFIN DE REDUIRE LES RISQUES D’ELECTRO-CUTION, NE PAS DEPOSER LE COUVERCLE, IL N’Y A AUCUNE PIECE UTILISABLE A L’INTERIEUR DE CET APPAREIL. NE CONFIER LES TRAVAUX D’ENTRETIEN QU’A UN PERSONNEL QUALIFIE. Ce symbole a pour but de prévenir l’utilisateur de la présence d’une tension dangereuse, non isolée se trouvant à

  • Marantz PD4220V, 40 Color System Settings Menu Setting the video signal format Use these operations to set the color systems of composite video signals or Y/C input signals. Example: Setting the color system to “3.58 NTSC” 1. On the MAIN MENU, select “COLOR SYSTEM”, then press the MENU/ENTER button. The “COLOR SYSTEM” screen appears. 2. To select “ 3.58NTSC ” ... Use the 䊴 and 䊳 buttons to select “ 3.58NTSC ”. The mode switches as follows each time the 䊴 or 䊳 button is pressed: → AUTO ↔ 3.58NTSC ↔ 4.43NTSC ← → SECAM ↔ PAL-M ↔ PAL-N ↔ PAL60 ↔ PAL ← COLOR SYSTEM EXIT COLOR SYSTEM : 3.58NTSC RETURN A

  • Marantz PD4220V, 29 Setting the time for INVERSE/WHITE Set a time duration. Example: Setting to that the INVERSE mode starts in 2 hours and proceeds for one hour and a half. Perform Steps 1-3 of INVERSE, then... 4. Use the 䊴 and 䊳 buttons to select “ON”, then press the MENU/ENTER button. THE “INVERSE/WHITE” screen appears. 5. Adjust the time using the ▲▼ 䊴 and 䊳 buttons. The mode switches as follows each time the 䊴 or 䊳 button is pressed: • WORKING TIME →ON ↔ 00H03M ↔ 00H06M ↔ ..... ↔ 12H42M ↔ 12H45M← • WAITING TIME →00H03M ↔ 00H06M ↔ 00H09M ↔ ... ↔ 12H42M ↔ 12H45M← INVERS

  • Marantz PD4220V, 36 Video Wall setting Use this feature to configure a 2×2 or 3×3 video wall. Set “ADVANCED OSM” to “ON” in the main menu (1/ 2), then perform the following operations. 1. On the MAIN MENU, select “OPTION3”, then press the MENU/ENTER button. The “OPTION3” screen appears. 2. Use the ▲ and ▼ buttons to select “VIDEO WALL”, then press the MENU/ENTER button. The “VIDEO WALL” screen appears. VIDEO WALL EXIT DIVIDER POSITION DISP. MODE AUTO ID IMAGE ADJUST P. ON DELAY PLE LINK REPEAT TIMER : 1 : SPLIT :

  • 3 Warning Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/ Data Processing Equipment ANSI/NFPA 75. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when

  • Marantz PD4220V, 17 *1 Only when AUTO PICTURE is OFF *2 RGB/PC only *3 The default value is PC for model PD4220V. *4 The default value is LOW for model PD4220V. Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET REFERENCE OPTION2 PWR. MGT. OFF←→ON YES 26 CINEMA MODE OFF←→ON YES 27 LONG LIFE PLE AUTO/LOCK 1/LOCK 2/LOCK 3 YES 27 ORBITER AUTO 1 YES 28 AUTO 2 YES 28 MANUAL H-DOT/V-LINE/TIME YES 28 OFF YES 28 INVERSE OFF YES 28 ON WORKING TIME/WAITING TIME YES 28 WHITE YES 28 SCREEN WIPER OFF Y

  • Marantz PD4220V, 10 Note: 1. The VIDEO1 and RGB1 terminals can be used for either INPUT or OUTPUT. When LOOP OUT is ON, do not connect an OUTPUT signal from another unit, that will place an extraordinary load on the other unit and may damage it. 2. LOOP OUT can not be turned ON while signals are input to RGB1 terminal. 3. LOOP OUT can be turned ON while signals are input to RGB1 terminal if the POWER is switched ON. Information • To loop signals out to another plasma display, set the LOOP OUT to ON. • To create a video wa

  • Marantz PD4220V, 38 P. ON DELAY (Power on delay) Use this function to activate power-on delay. Turn on the AUTO ID before the following operations. Example: Setting “ON” Perform Steps 1-2 of VIDEO WALL, then... 3. Use the ▲ and ▼ buttons to select “P. ON DELAY”. 4. Use the 䊴 and 䊳 buttons to select “ON”. The mode switches as follows each time the 䊴 or 䊳 button is pressed: OFF ↔ ON VIDEO WALL EXIT DIVIDER POSITION DISP. MODE AUTO ID IMAGE ADJUST P. ON DELAY PLE LINK REPEAT TIMER : 1 : SPLIT : OFF : ON : OFF : OFF SEL. RETURN ADJ. Information 䡵 P. ON DELAY settings ON...... Turns on the main power o

  • Marantz PD4220V, 19 Reducing noise in the picture Use these settings if the picture has noise due to poor reception or when playing video tapes on which the picture quality is poor. Example: Setting “NR-3” 1. On the MAIN MENU, select “PICTURE”, then press the MENU/ENTER button. The “PICTURE” screen appears. 2. Use the ▲ and ▼ buttons to select “NR”. PICTURE 1 / 2 EXIT CONTRAST BRIGHTNESS SHARPNESS COLOR TINT PICTURE MODE NR NEXT PAGE : NORMAL : OFF SEL. RETURN ADJ. 3. Use the  and  buttons to select “NR-3”. The mode swi

  • Marantz PD4220V, Precautions Please read this manual carefully before using your plasma monitor and keep the manual handy for future reference. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside of this unit. This symbol alerts the user that important literature concerning the operation and maint

  • Marantz PD4220V, 32 Option3 Settings Menu Using the timer This function sets the monitor to turn ON/OFF automatically at a set time. Set “ADVANCED OSM” to “ON” in the main menu (1/ 2), then perform the following operations. 1. On the MAIN MENU, select “OPTION3”, then press the MENU/ENTER button. The “OPTION3” screen appears. 2. Use the ▲ and ▼ buttons to select “TIMER”, then press the MENU/ENTER button. The “TIMER” screen appears. TIMER EXIT PRESENT TIME PROGRAM : OFF SEL. RETURN MENU/ENTER OK 3. Set the TIMER using ▲▼ 䊴 and 䊳 bu

  • Marantz PD4220V, 20 Changing the Gamma Curve This feature adjusts the brightness of the midtone areas while keeping shadows and highlights unchanged. Example: Setting “3” Set “ADVANCED OSM” to “ON” in the MAIN MENU (1/2), then perform the following operations. 1. On the MAIN MENU, select “PICTURE”, then press the MENU/ENTER button. The “PICTURE” screen appears. 2. Use the ▲ and ▼ buttons to select “GAMMA”. 3. Use the  and  buttons to select “3”. The mode switches as follows each time the  or  button is pressed: → 1 ↔ 2 ↔ 3 ↔ 4 ← PICTURE 2 /

Related Products and Documents (Flat Panel TV):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Laurel Mountain Whirlpools Walk-In Owner's manual laurel-mountain-whirlpools/walk-in-8OF.pdf 29 Nov 2022 10
2 Australian Warning Systems 4200 Series Installation and operation instructions australian-warning-systems/4200-series-957.pdf 11 Sep 2023 2
3 SEM 1201P Operational & maintenance manual sem/1201p-81E.pdf 06 Oct 2022 36
4 Schwinn IC2 Indoor Cycling Bike Assembly manual schwinn/ic2-indoor-cycling-bike-3OY.pdf 26 Jan 2023 28 5.41 Mb
5 Star Micronics PR921 Mounting manual star-micronics/pr921-24D.pdf 04 Jan 2023 2 0.26 Mb
6 Proxima DP8000 Brochure proxima/dp8000-6VV.pdf 17 Sep 2023 4

Similar Resources:

  • Samsung

    UE40JU7080

    (60 pages)
    Thank you for purchasing this Samsung product. To receive more complete service, please register your product atwww.samsung.com/registerModel ___________ Serial No. ____________user manual2015-03-18 오후 5:04:11 …
  • LG

    42PG69

    (116 pages)
    Please read this manual carefully before operating your TV.Retain it for future reference.Record model number and serial number of the TV. Refer to the label on the back cover and quote thisinformation.To your dealer when requiring service.PLASMA TVOWNER’S MANUALPLASMA TV MODELS4422PPGG6699****5500PPGG6699****ENGLISHTrademark of the DVB Digital Video Broad …
  • Samsung

    LE32N7

    (111 pages)
    LCD TVLE32N7 LE40N7 LE46N7Owner’s InstructionsBefore operating the unit,please read this manual thoroughly,and retain it for future reference.ON-SCREEN MENUSPC DISPLAYPICTURE IN PICTURE (PIP)TELETEXTRegister your product at www.samsung.com/global/registerBN68-01007S-01Contact SAMSUNG WORLD-WIDEIf you have any questions or comments relating to Samsung produ …
  • Sanyo

    CE42SRE1

    (64 pages)
    CE42SRE1LCD MonitorMoniteur d'affichage à cristaux liquidesLCD-MonitorLCD-DisplayMonitor LCDMonitor de LCD Instruction ManualManuel d'utilisationBedienungsanleitungGebruiksaanwijzingManuale d'IstruzioniManual de instruccionesEnglish Page 2~11Deutsch Seite 22~31 Français Page 12~21 Nederlands Bladzijde 32~41 GBDFNLItaliano Pagine 42~51 …
  • LG

    M4210C

    (58 pages)
    Make sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for furture reference.See the label attached on the product and give the information to your dealer when you askfor service.M4210CUser’s Guide …
  • Samsung

    PS50B451B2W

    (4 pages)
    English - 1The Supplied AccessorisOwner’s Instructions Remote Control/AAA Batteries (2ea)Power Cord Cloth-CleanFerrite Core for Power CordScrew (4ea) Cover-Bottom Holder-Ring (4ea)Installing Batteries in the Remote ControlPDP TVQUICK SETUP GUIDEBN68-02137A.indd 1 2009-03-30 오후 3:45:25 …

Comments, Questions and Opinions: