McIntosh MCD 7007 Owner's Manual
|
is controlled by the preselected program or the continuous loop. SCAN If the SCAN button was used to activate the player the SCAN indicator will light and remain lighted until all tracks have been scanned. REVIEW When the REVIEW button is activated the indicator is lighted and the program is displayed in sequence on the appropriate TRACK, INDEX, and MIN/SEC indicators. REPEAT The REPEAT indicato
McIntosh MCD 7007, PLAYER LOCATION The MCD 7007 may be installed in a Mclntosh cabinet or custom installed in furniture of your choice. Always provide adequate ventilation. Never place it above heat generating components such as high powered amplifiers. Provide 1½ inches (3 cm) of space above the player to maintain with a cooling air flow. Always use the compact disc player horizontal- ly, out of direct sunlight and away from other heat sources. REMOVE THE TRANSIT SCREWS On the bottom of the player are two screws which lock the player mech
McIntosh MCD 7007, Fold out this manual's back cover to assist you in locating the controls. The numbers on the photographs refer to the paragraphs that follow, The glass upper half of the MCD 7007 front panel contains the CD drawer, the IR REMOTE SENSOR, the REMOTE response LED, the DAMAGED DISC indicator and the message center. The message center displays the current status of the mode of operation, disc time, the CD functions in use and the horizontally displayed volume level indicator. The black anodized lower half of the front panel contains the buttons to program
McIntosh MCD 7007, If you touch NEXT TRACK during play of the last track, the ERROR sign will light as a reminder that there is no next track. Play of the last track continues. LISTENING WITH HEADPHONES-14. With headphones connected to the PHONES jack, you can listen to discs without having to use an amplifier. Adjust the sound level with the LEVEL control. The headphones must have a 0.25 inch (6.3 mm) jack plug and an impedance between 8 and 1000 ohms. -17. Should you wish to hear a portion of the disc repeatedly, touch the button a
The back cover of this manual folds out to show photographs of the front and rear panels of the MCD 7007. Fold it out to assist you in identifying and locating the connections. The letters refer to the paragraphs that follow. The back panel of the MCD 7007 has connectors labeled FIXED OUTPUT, VARIABLE OUTPUT, REMOTE, a port marked DIGITAL OUTPUT and the AC power cord. The VARIA
McIntosh MCD 7007, 15. Nonuse Periods - Unplug the power cord from the AC power outlet when left unused for a long period of time. 16. Damage Requiring Service - Service must be performed by qualified service personnel when: A. The power supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has been spilled into the instrument; or C. The instrument has been exposed to rain; or D. The instrument does not appear to operate normally or exhibits a marked change in performance; or E. The instrument has been dropped, or the enclosure damaged. 17. Servicing - Do not attempt to service beyond that described in the operatin
McIntosh MCD 7007, The third generation Compact Disc player continues the world-wide Mclntosh reputation for technological advancement as the reason for a new model. Every aspect of performance is improved: focusing and tracking, decoding, error correction, digital filtering, digital to analog conversion (converters are specially selected for matched channel to channel linearity.) The MCD7007 uses a new integral massive cast disc drive platform whose variable reluctance suspension system is adjusted and tuned to reduce or eliminate bo
McIntosh MCD 7007, MESSAGE CENTER DISPLAY-5. The display in the message center presents many different types of information. As soon as the POWER button is touched to turn the player on, the message center shows a series of zeros in TRACK, INDEX and TIME. The eLAPsed time indicator and the VOLUME bar are also lighted. The LOAD button opens and closes the disc drawer. Once opened, place a disc in the drawer label side up. When the LOAD button is used to close the drawer, the laser pen will read the contents of the disc from the encoded data. The message center information will change to show the number of tracks and the total recorded time on the disc. The player
McIntosh MCD 7007, 22. CLEAR When touched will erase from the memory an entry error or break out of an continuous loop. 23. REMOTE SENSOR Receives the coded infrared signals from the remote control. 24. DAMAGED DISC/MUTE Lights when a playing disc is damaged or has errors which are not correctable by electronic interpolation. It also lights when the player is muted by more seriously damaged discs, or when PAUSE, STOP, REV, FF , BACK TRACK and NEXT TRACK are used and when a disc is not playing. 25. REMOTE This LED lights when the IR Remote Control is used to operate the functions of the MCD 7007. 26. PANLOC Turn to secure or release the player from the cabinet. 8 FRONT PANEL
McIntosh MCD 7007, POWER-1. Touch the POWER button to turn the player on. The TRACK, INDEX, TIME, eLAPsed time and VOLUME indicators will light up in the display area. Touch POWER again and the player is turned off and the indicators turn off. LOAD-2. Touch the LOAD button and the LED above this button will illuminate, then after 1 second the drawer will open. If the drawer is obstructed, it will not continue to open. Should this happen remove the obstruction, touch LOAD twice in succession to bring the drawer fully out. Hold the disc at the rim and place it, label side up, in the disc drawer. Close the drawer by touching PLAY, SCAN or LOAD. Use PLAY if you
7. Programming is not working properly. • The disc is dirty or badly scratched. Clean the disc or try programming with a scratch-fee disc. • The microprocessor has not processed the commands properly. Clear the program by touching STOP and store it again; re-start play. • All 20 memory places are already programmed and you have missed the ERROR sign that shows thi
McIntosh MCD 7007, Repeat this procedure to attach the mounting strip to the (eft side of the panel. 6. Attach the PANLOC Brackets Using two screws of the proper length in the A holes on each side, attach the PANLOC brackets to the cabinet panel; the short flange is mounted against the front (face) of the cabinet panel. The screws pass through the PANLOC bracket flange, the cabinet panel, and then through the mounting strips previously mounted. 7. Install the Instrument Guide the AC power cord through the panel opening to the back of the cabinet; then, slide the instrument into the opening carefully so that the rails on the bottom of each side of the chassis engage the tracks on the mounting brackets. Continue
McIntosh MCD 7007, Contents INTRODUCTION 3 INSTALLATION 4, 5 HOW TO CONNECT 6 FRONT PANEL CONTROLS 7, 8 OPERATION 9, 10, 11, 12, 13 HELPFUL HINTS 14, 15 PERFORMANCE DATA 16 Your MCD 7007 Compact Disc Player will give you many years of satisfactory performance. If you have any questions, please contact, CUSTOMER SERVICE Mclntosh Laboratory Inc. 2 Chambers Street Binghamton, New York 13903-9990 Phone: 607-723-3512 Take Advantage of 3 Years of Contract Service. . . Fill in the Application NOW. MclNTOSH THREE YEAR SERVICE CONTRACT An application for A THREE YEAR SERVICE CONTRACT is incl
McIntosh MCD 7007, TYPICAL AUDIO PERFORMANCE NUMBER OF CHANNELS 2, left and right FREQUENCY RESPONSE 20-20,000 Hz, +0, -0.3 dB DYNAMIC RANGE 96 dB (114 dB EIA) SIGNAL-TO-NOISE RATIO 107 dB (A) CHANNEL SEPARATION 102 dB (at 1000 Hz) TOTAL HARMONIC DISTORTION 0.0012% (at 1000 Hz) WOW AND FLUTTER Quartz crystal precision SAMPLING RATE 176.4 kHz D/A CONVERSION Quadruple oversampling (176.4 kHz) with digital filter and two 16 bit D/A converters ERROR CORRECTION SYSTEM Cross Interleave Reed Solomon Code (CIRC) AUDIO OUTPUT LEVEL 2.5V IMPEDANCE HEADPHONES 8-1000 ohms DIGITAL OUTPUT Output for digital signal processing OPTICAL READOUT SYSTEM LASER Semi-conduct
McIntosh MCD 7007, IMPORTANT SAFETY INSTRUCTIONS THESE INSTRUCTIONS ARE TO PRO- TECT YOU AND THE MclNTOSH IN- STRUMENT. BE SURE TO FAMILIARIZE YOURSELF WITH THEM. 1. Read all instructions - Read the safety and operating instructions before operating the instrument. 2. Retain Instructions - Retain the safety and operating instructions for future reference. 3. Heed warnings - Adhere to warnings and operating instructions. 4. Follow Instructions - Follow all operating and use instructions. WARNING: TO REDUCE RISK OF FIRE OR ELECT
McIntosh MCD 7007, memory from TRACK to INDEX or to TIME. Touch SELECT once and the TRACK indicator will flash on and off which indicates the numeric key pad TRACK selection is connected to the memory input. Touch SELECT twice which causes the INDEX indicator to flash and which connects the numeric key pad INDEX selection to the memory input. Touch SELECT three times and the MINutes flash for programming by any given minute in a track. When SELECT is touched four times programming can be started on the second. Suppose you wish to hear track 7 at 4 minutes and 18 seconds. Touch in se
McIntosh MCD500 CD Player Owner's manual
MCD500 |
McIntosh MCD 7005 CD Player Preliminary owners manual
MCD 7005 |
McIntosh MCD1100 CD Player Owner's manual
MCD1100 |
Rio Volt SP250 CD Player Operation & user’s manual
Volt SP250 |
McIntosh MCD301 CD Player Owner's manual
MCD301 |
McIntosh MCD201 CD Player Owner's manual
MCD201 |
McIntosh MCD205 CD Player Owner's manual
MCD205 |
McIntosh MCD301 CD Player Owner's manual
MCD301 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | South | S82V | Manual | south/s82v-D5O.pdf | 07 Oct 2023 | 17 | |
2 | HP | PW460t | Operation & user’s manual | hp/pw460t-3W2.pdf | 24 May 2023 | 82 | |
3 | Sony | D-EJ017CK Marketing | Specifications | sony/d-ej017ck-marketing-N8G.pdf | 24 Jun 2023 | 2 | 0.43 Mb |
4 | Oracle | OTIU 608-1 | Manual | oracle/otiu-608-1-5I4.pdf | 03 Sep 2023 | 7 | |
5 | Engel | 12VDCBattcharger | Datasheet | engel/12vdcbattcharger-7PZ.pdf | 22 Dec 2022 | 1 | 0.08 Mb |
6 | Philips | HD7457 | Operation & user’s manual | philips/hd7457-3N4.pdf | 22 Jun 2022 | 12 |
Philips
AZAZ1301AZ1325CD SoundmachineNeed help? Call us!Philips representatives are ready to help youwith any questions about your new product.CALL US BEFORE YOU CONSIDERRETURNING THE PRODUCT! 1-800-531-0039or visit us on the web at www.philips.comSEEWHYINSIDEIMPORTANT!Return your WarrantyRegistration Cardwithin 10 daysUser ManualManuel d'utilisation …
AZ1325/17X(6 pages) |
VINCENT
VincentCD-S8CD-Player mit Röhren-AusgangsstufeTube CD Player Lecteur de CD à tubesBedienungsanleitung deutschInstructions for use englishManuel d’utilisation français
…
CD-S8(64 pages) |
Pioneer
Operation Manual C:>2>4AB2> ?> M:A?;C0B0F88High power CD player with FM/MW/LW tuner@>83@K20B5;L :><?0:B-48A:>2 2KA>:>9 <>I=>AB8A FM/MW/LW BN=5@><DEH-1610English CAA:89
…
DEH-1610(36 pages) |
Philips
FWM352Mini Hi-Fi SystemUser manualManuel d'utilisationManual del usuarioBenutzerhandücherGebruikershandleidingenManuale per l'utenteAnvändarhandböckernaBrugermanualKäyttöoppaitaManual do usuário pg001-027_M352_22_Eng 2005.12.23, 15:521
…
FWM352(27 pages) |
JVC
For Customer Use:Model No.Serial No.Enter below the Model No. and Serial No.which are located on the rear, bottom orside of the cabinet. Retain this informationfor future reference.STANDBYSTANDBY/ONMAXMINLEVELPHONESPLAY MODE CD EDITREC SOURCESELECTORCD RECSTOP PLAY PAUSEREC SOURCEDIGITAL CD LINE MICOPEN/CLOSEOPEN/CLOSECANCELSETMENUPAUSEREC/REC MUTINGPLAYSTO …
XL-R2010BK(47 pages) |
Volvo
Instruments, switches and controlsDescription on pageIAir vents1:202Windscreen wash/wipe and headlight wipers1:9, 1:113Rear foglight1:11Instrument lighting1:114Headlights and parking lights1:65Combined instruments1:2-1:56Direction indicators, main/dipped beam, headlight flash1:6Cruise control (extra equipment)1:197Hazard warning flashers1:108Air mix1:209Air …
850(147 pages) |
Sony Minidisc Recorder MD Walkamn MZ-R2Guide: Sony MD Walkamn MZ-R2 (QN2ONZ, Upd.01st Oct 2023) MD Walkamn MZ-R2, 67 |
ABB Protection Device ret650ret650 (Protection Device ePDF Manual, #4W9875) ret650, 70 |
Seaira Global Dehumidifier WatchDog 900cDehumidifier PDF Quick start manual WatchDog 900c, 15 |
AMX Touch Panel Modero X Series G5 MXT-2001-PANTouch Panel #289RK3 Modero X Series G5 MXT-2001-PAN, 74 |
GE Cooktop JBP72SMSSGE JBP72SMSS Guide (Dimensions and installation information), @4L9JK3 JBP72SMSS, 2 |
Yamaha Electronic Keyboard HS-4Yamaha HS-4 User Manual (Doc Type: Electronic Keyboard Operation & user’s manual) HS-4, 86 |
Makita Grinder 9556PB9556PB Instruction manual - WR82IW 9556PB, 72 |
Eagle GPS ExpeditionEagle GPS Expedition Installation and operation instructions manual Expedition, 62 |
DreamGEAR Headphone DG360-1711DG360-1711 (Headphone ePDF Guide, #A1W9G5) DG360-1711, 1 |
ALIBI Security Camera ALI-CD1720PVFALIBI ALI-CD1720PVF Manual (Quick installation and user manual), @1YZ8E9 ALI-CD1720PVF, 4 |
Winix Air Cleaner NK105#G5A488 NK105: Winix Air Cleaner Owner Documentation NK105, 80 |
HEIDENHAIN Control Panel TNC 620#Q713EY: TNC 620 Control Panel Operation & user’s manual TNC 620, 499 |