Manualios.com

Metz Clarus LCD-TV ML Operating Instructions Manual

  • Clarus LCD-TV ML LCD TV
  • ma1lHD.k4RNWg
  • Operating Instructions Manual
  • PDF / Adobe Acrobat Reader
  • 114

Metz Clarus LCD-TV ML Manual Online:

3.5, 942 votes
Metz Clarus LCD-TV ML User Manual
Metz Clarus LCD-TV ML User Guide
Metz Clarus LCD-TV ML Online Manual

Text of Metz Clarus LCD-TV ML User Guide:

  • 27 12. General Sound Settings Base width and spatial sound The menu points base width and spatial sound are only shown when the function "SRR WOW" is turned off.. Base width In the case of stereo transmissions, the base width (= spatial distance between the loudspeakers) can be artificially widened to achieve a larger stereo triangle. Spatial sound In the case of mono

  • Metz Clarus LCD-TV ML, 100 Calling the menu MENU The settings of the satellite antenna system must be entered in the menu "Configuration" so that the TV set knows them. These settings should always be made in the order in which they are shown in the right-hand column of the menu, starting at the bottom, i.e. LNB supply voltage, DiSEqC system, etc.. LNB supply voltage The LNB voltages for selection of the polarisation (hori- zontal H = 18V, vertical V = 14V) are already set and do not nor- mally need to be changed. If the cable to the satellite antenna is very long, the vol- tages reaching the LNB may be too low. In such cases, the

  • 74 Connection of external devices with YUV compo- nent output to the "COMPONENT IN" RCA jacks. The signal type always refers to the input and output of the AV device. AV devices equipped with a YUV jack can be con- nected to the LCD TV by means of a YUV cable (see page 86). In the "AV Devices" menu, the con- nected AV device must be registered with signal OUT &qu

  • Metz Clarus LCD-TV ML, 34 b) Permitted programmes: Activate the childlock as described in step a). Use the corresponding numeric key to select the menu item "Permitted xx progs." (xx = TV, radio or AV). Press the "OK" key and, in the setting win- dow, enter the programme positions with the numeric keys or use the - + key to select the des- ired programme positions. • Press the "OK" key to save the new settings. c) TV start – TV end Activate the childlock as des- cribed in step a). In the setting window, use the cursor control key to select the start and end times and enter the desired times with the numeric keys

  • Metz Clarus LCD-TV ML, 94 38. Glossary Tone settings The tone can be set to either "Normal" or "Speech". In the setting "Speech", the bass and treble components of the sound signal are set to make speech as easy to understand as possible. The setting "Normal" is recommended for music programmes. VCR The VCR function provides an optimal picture qua- lity when playing back recordings from tape devi- ces such as camcorders or video recorders. Volume correction The various stations broadcast their sound at diffe- rent volumes. The TV set can automatically com- pensate for these differences in the v

  • Metz Clarus LCD-TV ML, 87 35.1 Connecting a Hifi Amplifier/AV Receiver Metz LCD-TV HiFi-amplifier AV-Receiver    Digital audio signal formats (depending on the source)  analogue audio signal R+L (stereo)  Centre IN is always possible if the AV receiver offers this. Can be used in combination with  or  if this option is available. It is always possible to use the TV speakers as the centre speaker if the AV receiver has this output available. The advantage of this is that the TV speakers can be used as the centre speaker, thus making it unnecessary to set up an external centre spea- ker.  607 47 2042.A1 Clarus GB 04.12.2007 9:59 Uhr Seite 87

  • Metz Clarus LCD-TV ML, 67 23. Station Logo With the aid of the VPS signal, a station logo with a maximum length of 15 characters is automati- cally assigned to each station. If this automatic assignment does not work, or if you want to use a different logo, you can change the setting manually. Setting the station logo • Press the "MENU" key. • Press the white key to open the “station table”. • Press the F2 key to enable editing of the station table. • Select the programme position whose logo you wish to change. • Press the cursor control key  to move to the other column. • Use the corresponding numeric key (in the exam- ple: ) to select "Logo input". • The various l

  • Metz Clarus LCD-TV ML, 110 Various pay TV stations broadcast portal stations. These portal stations are filled with sub-stations or optional channels. In station search (see ch. 22) in "Search settings" the setting "all", "only free" or "free+CICAM" must be set so that these stations can be found too. After a station search, the portal sta- tions and the accompanying optional channels (may also be identified in the station table as SID=xy) will be shown in the station table on various program places. We have progr

  • Metz Clarus LCD-TV ML, 12 Teletext is an additional service provided free of charge by many TV stations. It is an "electronic magazine" through which you can browse in various ways. Opening Teletext: • Press the "TEXT" key. If the selected station offers "TOP-Text", a "card file" is displayed (see the picture on the left). If "TOP-Text" is not available, Teletext page 100 is displayed (see the pictu- re below). • In the TOP-Text card file, you can select the desired cards with the cur- sor control key or with the numeric keys. • Press the "OK" key to open the selec- ted card. Controlling the videotext when pages of non-TOP s

  • Metz Clarus LCD-TV ML, 92 38. Glossary AV programme position AV devices have one or more connection sockets, depending on the model. The designations of the- se sockets are marked on the device (e.g. AV1). On the AV device, you can select which socket you want to use. The selected socket is shown on the display of the AV device (e.g. A1 for socket AV1). Code The settings for the childlock function are protec- ted by a four-digit code: you can enter any des- ired code, but you should note it for future use. If you have forgotten your code, please consult your local dealer

  • Metz Clarus LCD-TV ML, 14 Displaying all Teletext marks 6) If you have set marks for a programme position, you can display an overview of these marks by pressing the F3 key. The displayed list shows whe- re the marks are set. Press F3 again to hide the list. You can select the individual marks in the list with the numeric keys. Clearing Teletext marks 6) Open the Teletext page whose mark is to be dele- ted and press the red key "Delete" to delete the mark. Subtitles in Teletext Your TV set is capable of displaying subtitles. When a programme for which subtitles exist starts, the TV station displays a b

  • Metz Clarus LCD-TV ML, 104 For the manual search, you must know the fre- quency, the symbol rate and the polarisation of the station for which you want to search. Executing the manual search • Press the MENU key to open the TV menu. • Press the red key to open the menu "Confi- guration" • Press the appropriate numeric key (in this exam- ple  to select "DVB-S". • The cursor is located on the line "LNB supply voltage". • Press the appropriate nume- ric key (in this example  to select "Manual search". • The cursor then moves to "Satellite". If more than one satellite i

  • Metz Clarus LCD-TV ML, 76 You can define an initial programme position in this TV set. This initial programme position is used primarily to select the AV programme position if you use an external receiver. Setting the initial programme position This menu item is not available in a 2 ** menu. Select a receiver (satellite or set-top box) in the menu "AV devices" and connect the receiver to the TV set (see also Section 25, Registering AV Devices"). • Press the "AV" key. • Use the numeric keys to select the position "Sat/Set- top" in the AV menu. • Press the "MENU" key to open the TV menu. • Press the red key to open th

  • 62 The TV set will normally detect the colour standard (PAL, SECAM, NTSC, NTSC44, PAL60, PAL M) automatically. If this automatic selection does not provide satis- factory results (which should happen only rarely), you can select the colour standard manually for each programme position. The colour standard is set in the factory to "Auto- matic". Setting the colour stan

  • Metz Clarus LCD-TV ML, 32 Opening the menu 13. Automatic zoom The menu item "Automatic zoom" is not available in a 2 ** menu. When the automatic zoom function is active, pro- grammes in a "widescreen" format (such as pro- grammes in 16:9) are expanded to fill as much of the screen as possible. If the function is inactive, the programmes are dis- played in their original format. Activating the automatic zoom 2) • Press the "MENU" key. The TV menu appears on the screen. • Press the blue key . The menu "Picture and sound" and the menu it

  • Metz Clarus LCD-TV ML, 83 When receiving a dual-language pro- gramme, you can switch between the two sound channels. In TV mode, press and hold the yellow key until the sound function "Sound mode" is selected. Then use the - + key to select Sound 1 or Sound 2. 32. Sound 1, Sound 2 Headph. Vol. Sound mode Cannel 2 Spatial Spatial Sound mode Cannel 2 Balance 31. Connecting Headphones The headphone socket is located on the right side at the back of the TV set. Tilt the flap on the Milos up with your fingernail. On the Puros or Talio open the flap by pressi

  • Metz Clarus LCD-TV ML, 28 12.1 Sound Settings for Programmes via TV Menu Opening the menu Some of the menu items are not available in a 2 ** menu. Volume correction Various TV stations broadcast their programmes with different sound volumes. This volume diffe- rence can be minimised by correcting the volume. This adjustment remains active even if the stan- dard sound values are recalled. Adjusting the volume correc - tion: • Press the "MENU" key. The TV menu appears on the screen. • Press the blue key . The menu "Picture and sound&quo

  • 90 • Use the cursor control key  to select the line "Recording device". If only one such device exists, it is then display- ed. If further recording devices exist, you can select the desired device with the aid of the - + key. • Press the "OK" key to save the settings. • On the playback device (in this example, the DVD player) sta

  • 3 Contents Configuration Worth knowing 22.3 Automatic DVB-C station search. . . . . . . . . . 65 Manual DVB-C station search. . . . . . . . . . . . 66 23. Station Logo . . . . . . . . . . . . . . . . . . . . . . . . 67 24. Sorting Stations. . . . . . . . . . . . . . . . . . . . . . 68 25. Reg. AV Devices . . . . . . . . . . . . . . . . . . . . . 69 - Data Logic . . .

  • Metz Clarus LCD-TV ML, 48 In the menu "Sound settings", you can activate a two-stage mute function. When this function is active, the volume in TV mode can be reduced in two stages with the mute key . Activating the mute function • Press the "MENU" key to open the TV menu. • Press the red key to open the "Configura- tion" menu. • Press the "OK" key to move to the right side of the menu. • Use the cursor control key  or the corresponding nume- ric key (in the example: ( ) to select the menu item "Sound settings". • In the setting window, use the - + key to set the func- tion "Mute (2-stage)"

  • Metz Clarus LCD-TV ML, 53 Solution 2: • Press the MENU key . The TV menu appears on the screen. • Press the white key. The menu channel table appears with the active pro- gramme slot selected. • Follow the steps described under “24. Sort channels” to sort and save your favourite channels so that they appear at the top of the list, for example sort 1-50 and save them. • Select “EPG Settings” from the Confi- guration menu and under “Prog. select. in the channel table”, select “Channels 1-50” using the -+ key and save by pressing OK. The collection process will be halted if: - videotext is opened. - a r

  • Metz Clarus LCD-TV ML, 11 With the "TV menu", we provide you with an assistant to help you find your way through the many possible settings of the TV set. Don't be afraid to change any settings in the various menus. No changes will be saved unless you press the "OK" key to confirm them. If you are not sure whether you want to keep a changed setting, you can exit from the menu at any time, without saving any changes, by pres- sing the "EXIT" key. Within the TV menu, you can return to the pre

  • Metz Clarus LCD-TV ML, 81 • Use the - + key to select the desired scope of operation and press the "OK" key to save the new setting. 2    This menu permits you to configure the use of the TV set to a certain degree. All of the functions listed for the 1  menu are available and are supple- mented by the following functions: - Childlock - Timer control (sleep timer) - Automatic station search - Transfer of the TV station table from the TV set to a Data Logic video recorder. - Editing functions in the

Related Products and Documents (LCD TV):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Oki 42158411 Installation instructions manual oki/42158411-2YV.pdf 30 May 2023 15
2 OneRemote Radio PL2 Installation manual oneremote/radio-pl2-2HZ.pdf 17 Feb 2023 11
3 Parrot MKi9200 Operation & user’s manual parrot/mki9200-886.pdf 09 Sep 2022 32
4 Roadstar CLR-2750 Instruction manual roadstar/clr-2750-K51.pdf 02 Mar 2023 26 0.19 Mb
5 Weslo WLEL33408.0 Operation & user’s manual weslo/wlel334080-2T9.pdf 24 Jun 2023 24
6 gio Italia 500W Assembly instructions manual gio/italia-500w-2TV.pdf 28 Feb 2023 14

Similar Resources:

  • Philips

    15PF9945/37

    (4 pages)
    Quick Use and Hookup GuideImportant Notice/Warning . . . . . . . . . . . . . . . . . . . . .1Basic TV Operation . . . . . . . . . . . . . . . . . . . . . . . . . .1Remote Battery Installation . . . . . . . . . . . . . . . . . . .1Remote Control Button Descriptions . . . . . . . . . . . .1Hooking up the TelevisionBasic Cable/Cable Box TV Connections . . . …
  • Curtis

    LCD2226

    (1 pages)
    Curtco International LTD – www.curtcoint.com MASTER CARTON DIMENSIONS Length: TBA inches Weight: xxxx lbs Width: TBA inches Quantity: x /ctn Height: TBA inches 40 Ft Container: xxxxx pcs/ctn INDIVIDUAL BOX DIMENSIONS Length: TBA inches Weight: xxxx lbs Width: TBA inches UPC: 0 58465 xxxxx x Heig …
  • RCA

    LED42A45RQ

    (84 pages)
    Part No.: RN0342G0300Mode[ Number_Please register your product at WWW,rca,comPlease keep your sales receipt and keep the record ofthe serial number and the date of purchase in order toreceive warranty parts and service.The serial number is located at the back of the TV.Serial Number/ N_merode serie de TVDate of Purchase/ Fechade la compraChanging Entertainme …
  • Hyundai

    H-LED24V1

    (31 pages)
    ТЕЛЕВИЗОРЦВЕТНОГО ИЗОБРАЖЕНИЯЖИДКОКРИСТАЛЛИЧЕСКИЙ(LCD)LCD TVРуководство по эксплуатации Instruction manualH-LED24V1 …
  • Insignia

    IS-LCDTV26

    (1 pages)
    Philips RCA One For All SONY COMCAST DIRECTV DISH NETWORK MOTOROLA TIVO CHARTER CABLEVISION COXRecommended Models: PHDVD5, PH5DSS, PMDVR8, PDVR8Recommended Model: RCU807Recommended Model: URC-6690Recommended Model: RM-VL600Model: M1057 Model: RC23Models: VIP508, VIP622Model: DRC800Models: SERIES 3, HDModel: Charter Digital Model: …
  • Sony

    Bravia KDL-22EX350

    (140 pages)
    4-427-846-11(1)LCD TV/Televisor digital a color con pantalla de cristal líquidoOperating Instructions USManual de instrucciones ESLea este manual antes de usar el productoCentro de Asistencia de Sonyhttp://esupport.sony.com/ES/LA/Por favor no devuelva el producto a la tiendaRead this manual before using the productSony Customer Supporthttp://esupport.sony.c …

Comments, Questions and Opinions: