Monster Vision max 3D Owner's Manual

Text of Monster Vision max 3D User Guide:

• Monster Vision max 3D, 7 1 overview The following information will guide you through the connection, setup, and operation of the Vision Max3D Eyewear. For full 3D Home Theater enjoyment please read through the entire manual before proceeding. 1.1 BEFORE YOU BEGIN To ensure proper placement, connection, and setup of the Vision Max3D Eyewear please make sure that you take the time to plan out location and hookup based on how you intend to use them. Additionally, please make sure that you have everything available so that you can start enjoying your Vision Max3D Eyewear right away. IMPORTANT: The Vision Max3D Eyewear utilizes RF communication to sync with the TV; the most common usage requires that b

• 1 MONSTER VISION MAX 3D SYSTEM USER’S MANUAL table of contents I Product Safety ...................................................................................... 2 II Compliance ......................................................................................... 4 1 Overview ............................................................................

• Monster Vision max 3D, 15 4 installation anD setUP 4.1 INSTALLATION GUIDELINES The following guidelines describe the basics for proper setup and installation of your Vision Max3D Eyewear, please read through this section carefully so that you are prepared for all aspects of the installation. 4.1.1 Transmitter Placement The placement of the transmitter in relation to other electronics that transmit electromagnetic signal is important. Due to the nature of RF, outside electromagnetic interference can impede the performance. Be sure and keep the transmitter a good distance from the TV or any device that can emit electromagnetic signals. 4.1.2 Glasses Placement Additionally, the Eyewear requires a

• Monster Vision max 3D, 23 5.1.2 Delay Ghosting and Fuzziness When MAX 3D Eyewear is attached to certain 3D TV systems, some ghosting or fuzziness may appear. This is unlikely to occur when the IR receiver is used. Ghosting and fuzziness appears when there is a delay between the 3D emitter port and the alternating light emitting from the display. This delay between display and eyewear causes some of the left eye’s image to “bleed” into the right eye and vice-versa, yielding a ghost or faint double image on the display. In this case, since the video signal is delayed at the display, more delay must be added to the 3D emitter s

• 4 ii. comPliance Product Brand FCC Canada Glasses Monster YN3-50007001 9186A-50007003 Transmitter Monster YN3-01007001 9186A-50007003 II.i FCC COMPLIANCE THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDIN

• Monster Vision max 3D, 22 5.1 BASICS OF FINE TUNING The basis of 3D depth perception is seeing slightly different images in each eye. Both movie theaters and home entertainment systems work together with 3D eyewear to enable you to look at a flat screen, see different images in the left and right eyes, and experience the illusion of depth. 5.1.1 Shutter Lenses All 3D shutter glasses start with an alternating frame display which alternates displaying frames for the left eye and frames for the right eye. This is achieved by blocking the light of the left frames from reaching the right eye, and vice-versa. While viewing through the eyewear, each eye is actually rece

• 19 4.3.4 Optimizing IR 3D Sync Signal In order for the Vision Max3D Eyewear to function at their optimum level a strong IR Sync signal is a requirement. Starting with the IR Sensor as close, move the sensor near the IR 3D Sync on the TV until the strongest signal is achieved. Once you have the strongest signal possible, mount the IR Sensor with double sided t

• Monster Vision max 3D, 21 5 fine tUning Performance While the Vision Max3D Eyewear performs at a high level with the standard settings, some situations may call for more performance. For this reason the Max3D transmitter has a manual performance mode that allows you to tweak settings to get the optimum performance from the Eyewear. Fine tuning is performed using the joystick while the transmitter is in fine tuning mode; you should be a good distance from the TV usually in the normal seating area. Seeing as the transmitter is placed close to the TV, having a second person on hand to operate the joystick is advisable and makes fine tuning go quickly and accurately. NOTE: Any adj

• Monster Vision max 3D, 24 5.1.3 Duty Cycle Ghosting Duty Cycle is the adjustment of how long the lenses are open when an image is being displayed. The default when using the 3D Emitter Port cable is 100 percent, meaning that the lenses are open for the entire possible time. This is adjustable down to 10 percent of the possible open time. As the lenses close more, everything gets darker. Some displays do not make instantaneous transitions from the left frame to the right frame; instead they will take time for an image to transition from one frame to another frame. For example,

• Monster Vision max 3D, 9 2 transmitter oPeration 2.1 MAX 3D TRANSMITTER OPERATION RF Communication of Synchronization Signal Advanced RF communications enable the MAX 3D System to provide an extraordinary 3D viewing experience that is uninterruptable. Unlike IR-based 3D systems where the quality of the viewing experience is highly susceptible to line of sight obstructions, placement of transmitter considerations, and where the viewer sits relative to the transmitter; issues of sync between the MAX 3D Transmitter and MAX 3D Eyewear never arise thanks to the advance

• 18 3. Connect the Micro-USB end of the included USB cable to the transmitter. 4. Connect the other end of the USB to a power source following the guidelines in section 4.2.1 Max3D Transmitter Power on pg. 15. 4.3.3.1 Setup for TVs with IR 3D Sync 1. Turn on your 3D TV. 2. Place TV into 3D Mode (refer to TV owner’s manual for how to turn 3D on). 3. Hold or place the IR Sensor

• Monster Vision max 3D, 17 4.3.2.1 Detecting a Signal 1. Turn on your 3D TV. 2. Place TV into 3D Mode (refer to TV owner’s manual for how to turn 3D on). 3. The transmitter LEDs will display a RED moving pattern while the transmitter attempts to acquire a 3D signal, this will continue until it detects a 3D signal. Should the transmitter not acquire a 3D signal within 60 seconds, repeat steps 1 and 2. Upon finding a 3D signal, all LEDs turn GREEN. You are now ready to enjoy 3D viewing with your MAX 3D Eyewear... The MAX 3D Transmitter is preprogrammed and configured to operate with 3D TVs that have a 3D Sync Por

• Monster Vision max 3D, 5 II.ii CANADA COMPLIANCE Industry Canada: 9186A-50007003 Industry Canada: 9186A-01007003 ICES -003: Digital Apparatus: Spectrum Management and Telecommunications Policy; Interference-Causing Equipment Standard. This Class B digital apparatus complies with Canadian ICES -003. II.iii WARNING – SAFETY INFORMATION & PRECAUTIONS FOR INDOOR USE ONLY. NOT FOR USE AS SUNGLASSES. THE 3D KIT CONTAINS ELECTRONIC DEVICES AND THE FOLLOWING PRECAUTIONS SHOULD BE FOLLOWED: • Do not wear 3D glasses for any other activity excep

• Monster Vision max 3D, 14 After Restoring Defaults Firmware reverts to its original version – The Eyewear will reinstall new firmware once it syncs with the transmitter. Eyewear returns to an un-paired state – If the Eyewear was previously paired to a transmitter the pairing will need to be re-established. To Restore a Pair of Glasses to Factory Defaults 1. Press & hold the power button. 2. Continue holding the power button for around 10 seconds until the LED blinks in a heartbeat indicating pairing mode. 3. Continue holding the power button for around 10 more seconds until the LED sta

• Monster Vision max 3D, 13 3.2.1 Checking the Battery Level 1. Press and hold the button until the red LED comes on, then release the button. 2. The LED will blink in a pattern as described below; the LED will blink shorter and slower, the more charge the battery has. Blink Activity After Power-on Blink Blink Activity After Power-on Blink 2 long blinks 50% or more, 20 hours or more remains. 6 medium blinks 10% or more, 4 hours or more remains. 12 fast blinks 10% or less, eyewear will require charging before the end of a long movie. Power on indicator

• Monster Vision max 3D, ©2010 Monster, LLC 7251 West Lake Mead Blvd. Las Vegas, NV 89128 Monster, the Monster logo, Monster Vision, Max 3D, the Monster Vision logo, are trademarks or registered trademarks of Monster Cable Products, Inc. or its subsidiaries in the United States or other countries. All other company and product names may be trademarks of their respective companies. www.monstercable.com/max 3d

• Monster Vision max 3D, 2 i. ProDUct safety CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appli

• 10 Accessing Modes • During normal operation, the joystick is used to access different modes of operation. • Press & hold the joystick to the left to cycle through the available modes. • Once the desired mode is indicated, release the joystick to select a mode. • In any mode, the normal mode of operation resumes after 60 seconds

• Monster Vision max 3D, 26 5.5 ADJUSTING LENS DUTY CYCLE Duty cycle is the amount of time the lenses remain open to view images. Change in duty cycles appear in the form of brightness and ghosting of the image. Press Joystick Left • Lens Closes More • Brightness Decreases • Ghosting May Decreases • Number of ORANGE illuminated LEDs decreases as well their brightness Press Joystick Right • Lens Opens More • Brightness Increases UP DOWN PRESS RIGHTLEFT PRESS • Ghosting May Increase • Number of ORANGE illuminated LEDs increases as well their brightness 5.6

• Monster Vision max 3D, 25 5.2 ACCESSING FINE TUNING MODE With the transmitter in Normal Operating Mode: 1. Press & Hold the joystick until the first 2 LEDs illuminate GREEN. 2. Once they illuminate, release the Joystick. NOTE: The transmitter will default to Normal Operating mode within 60 Seconds of Inactivity. 5.3 FINE TUNING OPERATION Depending on the function being adjusted the joy stick is moved either left & right or up & down. Each function can be adjusted with press of the joystick or a press & hold. During a press & hold the s

• Monster Vision max 3D, 3 11. Power Cord Protection – Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance. 12. Cleaning – The appliance should be cleaned only as recommended by the manufacturer. 13. Non-Use Periods – The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time. To remove all power (supply

• Monster Vision max 3D, 28 6. Once the firmware file has opened, the Upgrade button is now active, click on the upgrade button to update the firmware. 7. During the process a status window will appear verifying that firmware is being updated. 8. After a short time the firmware is updated and verified by the appearance of a window that says Upgrade is Complete. 6.2 EYEWEAR UPDATES Firmware for the Eyewear is updated via the transmitter, when the firmware in the transmitter is updated it also contains update

• Monster Vision max 3D, 12 3 eyewear oPeration 3.1 CHARGING THE EYEWEAR The Eyewear is charged using the included USB Cable which can be connected to a computers USB port or by using a Monster iSlimCharger. Please refer to section 4.2 Power Guidelines on pg. 15 for information on accessing a power source to charge the Eyewear. IMPORTANT: Prior to operating the Eyewear with the transmitter it is recommended that the glasses be fully charged; please charge the glasses for 3 hrs, or until the LED indicates full charge as stated below. Charging Operation • When attached to a PC the Eyewear will charge, however they will not appear as a USB de

Related Products and Documents (3D Glasses):

Comparable Devices:

Similar Resources:

• Sony HMZ-T1 (2 pages) Get into the wearable HDTV from Sony. Experience your favorite movies and games with a virtual 150 inch screen and 5.1 Surround Sound- even in 3D!1 Dual OLED screens provide brilliant colors and clarity. Fully adjustable for a comfortable t. Now playing for your eyes and ears only.SpecicationsBullets• 1.Wearable HDTV• 2.Truly immersive 2D and 3D …

• Eschenbach MaxTV (28 pages) BedienungsanleitungUser ManualMode d‘emploiIstruzioni d‘usoManual de instruccionesGebruiksaanwijzingBetjeningsvejledningBrugsanvisningBruksanvisningKäyttöopasInstrukcja obsługiProvozní návod …

• Allview Visual VR2 (17 pages) 1 USERS MANUAL Visual VR2 Safety measures……………………………………………..2 Precautions & warnings on safety and health...............4 Children experiencing virtual reality.............................. 6 Proper environment for using Visual VR2......................7 Package contents............................................. …

• anko KC 43067381 (2 pages)  …

• Eschenbach MaxTV (28 pages) BedienungsanleitungUser ManualMode d‘emploiIstruzioni d‘usoManual de instruccionesGebruiksaanwijzingBetjeningsvejledningBrugsanvisningBruksanvisningKäyttöopasInstrukcja obsługiProvozní návod …

• Samsung SSG-3100GB (11 pages) ~3D Active GlassesSSG-3100GB:User'sGuide,0Zlt'f!:tftrh'iil/!!fptWf!t'•Fortheinitialpairing1.Iftheuser takesthe3Dglassesoutoftheboxandbrieflypressesthepowerbutton,theglassesareturnedonandthepairingprocessisstartedautomatically.~BesuretopowerontheTVbeforeyoupressthepowerbutton.2.Ifthefirstattempttopairfails,turnontheTV(20or3D)andpresstheP …

Comments, Questions and Opinions: