Manualios.com

Pioneer DEH-P2000 Service Manual

Pioneer DEH-P2000 Manual Online:

4.2, 1116 votes
Pioneer DEH-P2000 User Manual
Pioneer DEH-P2000 User Guide
Pioneer DEH-P2000 Online Manual

Text of Pioneer DEH-P2000 User Guide:

  • Pioneer DEH-P2000, 57 DEH-P2000,P20,P2050 7.2 DIAGNOSIS 7.2.1 DISASSEMBLY - Removing the Tuner Amp Unit(Fig.2) Remove the two screws. Remove the three screws. Remove the screw. Straighten the tabs at four locations indi- cated. Remove the Tuner Amp Unit. - Removing the Case Unit(not shown) 1.Remove the Case Unit. - Removing the Panel Assy(Fig.1) Disengage the stoppers at two locations. Remove the Panel Assy. - Removing the CD Mechanism Module (not shown) 1.Remove the four screws. 2.Disconnect the connector, and then remove the CD Mechanism Module. Fig.1 Fig.2 Panel Assy Tuner Amp Unit

  • Pioneer DEH-P2000, 59 DEH-P2000,P20,P2050 - New Test Mode S-CD plays the same way as before. If an error such as off focus, spindle unlocking, unreadable sub-code, or sound skipping occurs after setup, its cause and time occurred (in absolute time) are displayed. During setup, operational status of the control software (internal RAM: CPOINT) is displayed. These displays and functions are prepared for enhancing aging in the servicing and efficiency of trouble analysis. (1) Shifting to the New Test Mode 1 Turn on the current test mode by starting the reset from the key (it varies between the products). 2 Select S-CD for the source through

  • Pioneer DEH-P2000, 61 DEH-P2000,P20,P2050 (5) Display Examples 1) During Setup (When status no. = 11) TRK No. MIN. SEC. 11 11' 11" 2) During Operation (TOC read, TRK search, Play, FF and REV) The same as in the normal mode. 3) When a Protection Error Occurred Switch to the following displays (A) and (B) using the [BAND] switch: (A) Error occurrence timing display in absolute time. An example: Error occurred in 12th tune at 34'56" in absolute time. TRK No. MIN. SEC. 12 34' 56" (B) Error No. display An example: Error #40 (Off focus is detected) ERROR-40

  • Pioneer DEH-P2000, 39 DEH-P2000,P20,P2050 R 536 RS1/10S162J R 537 RS1/10S162J R 538 RS1/10S0R0J R 570 RD1/4PU103J R 579 RS1/10S331J R 580 RS1/10S103J R 602 RD1/4PU473J R 603 RS1/10S102J R 606 RD1/4PU102J R 607 RD1/4PU102J R 608 RD1/4PU102J R 610 RS1/10S222J R 611 RS1/10S473J R 613 RS1/10S0R0J R 614 RD1/4PU222J R 615 RD1/4PU473J R 616 RS1/10S222J R 617 RS1/10S473J R 618 RN1/10SE2002D R 623 RS1/10S473J R 624 RS1/8S473J R 625 RS1/10S0R0J R 626 RD1/4PU102J R 627 RS1/10S473J R 631 RS1/10S102J R 632 RS1/10S822J R 641 RD1/4PU102J R 651 RS1/10S222J R 652 RD1/4PU472J R 653 RS1/10S222J R 654 RD1/4PU222J R 655 RD1/4PU222J R

  • Pioneer DEH-P2000, 38 DEH-P2000,P20,P2050 5. ELECTRICAL PARTS LIST NOTES: - Parts whose parts numbers are omitted are subject to being not supplied. - The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS..... =====Circuit Symbol and No.===Part Name Part No. --- ------ ------------------------------------------ ------------------------- Unit Number : CWM6085(DEH-P2000/X1N/UC, DEH-P20/X1N/UC) Unit Name : Tuner Amp Unit MISCELLANEOUS IC 411 IC CA0008AM IC 451 IC PML003AM IC 551 IC PAL005A IC 601 IC PD4989A IC 631 IC S-80734AN Q 411 Transistor 2SA157

  • Pioneer DEH-P2000, 71 DEH-P2000,P20,P2050 Audio Adjustment Equalizer Curve Fine Adjustment You can adjust the center frequency of each equalizer curve band (LOW/MID/HIGH) and the Q factor (curve characteristics). 1. Press the AUDIO button for 2 or more seconds to select Equalizer Curve Fine Adjustment. Loudness Adjustment (LOUD) The Loudness function compensates for deficiencies in the low and high sound ranges at low volume. You can select a desired Loudness level. 1. Press the AUDIO button and select the Loudness mode (LOUD) in the Audio Menu. 3. Select the desired level with the 2/3 buttons. LOW += MID += HI 2. Switch the Loudnes

  • 40 DEH-P2000,P20,P2050 Q 411 Transistor 2SA1576 Q 412 Transistor DTC124EU Q 431 Transistor IMH3A Q 434 Transistor DTA124EU Q 502 Transistor 2SC4081 Q 551 Transistor DTC144ES Q 601 Transistor DTA114ES Q 651 Transistor 2SA933S Q 652 Transistor 2SB1236 Q 653 Transistor DTC124ES Q 971 Transistor IMX1 Q 973 Transistor 2SD1859 Q 981 Transistor 2SD2396 Q 982 Transistor IMD2A Q 991

  • Pioneer DEH-P2000, 52 DEH-P2000,P20,P2050 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1920 21 22 23 24 25 2627 28 Vref IN1_L IN2_L IN3_L IN4+_L AGND Loud- out_L SVin_L Front- out_L Rear- out_L FIE_L DGND IN4-_L CLK VCC IN1_R IN2_R IN3_R IN4+_R AGND Loud- out_R SVin_R Front- out_R Rear- out_R FIE_R STB IN4-_R DATA Isolator circuit Primary volume Anti Alias filter Treble Anti radiation filter Middle Bass Loudness volume FIE Fader volume Secondary volume Zero cross detect circuit Primary volume Anti Alias filter Middle Treble Bass Isolator circuit Anti radiation filter Loudness volume Zero cross detect circuit Fader volume Secondary volume FIE D

  • 2 DEH-P2000,P20,P2050 - CD Player Service Precautions 1. For pickup unit(CXX1285) handling, please refer to"Disassembly"(CX-916 Service Manual CRT2300). During replacement, handling precautions shall be taken to prevent an electrostatic discharge(protection by a short pin). 2. During disassembly, be sure to turn the power off since an internal IC might be destroyed when a con- necto

  • Pioneer DEH-P2000, 72 DEH-P2000,P20,P2050 Front Image Enhancer Function (FIE) The F.I.E. (Front Image Enhancer) function is a simple method of enhancing front imaging by cutting mid- and high-range frequency output from the rear speakers, limiting their out- put to low-range frequencies. You can select the frequency you want to cut. 1. Press the AUDIO button and select the F.I.E. mode (FIE) in the Audio Menu. Note: • After switching the F.I.E. function ON, select the Fader/Balance mode in the Audio Menu, and adjust front and rear speaker volume levels until they are balanced. • Switch the F.I.E. function OFF when using a 2-speaker system. Source Level

  • Pioneer DEH-P2000, 45 DEH-P2000,P20,P2050 1) Precautions • This unit uses a single power supply (+5V) for the reg- ulator. The signal reference potential, therefore, is connected to REFO(approx. 2.5V) instead of GND. If REFO and GND are connected to each other by mis- take during adjustments, not only will it be impossi- ble to measure the potential correctly, but the servo will malfunction and a severe shock will be applied to the pick-up. To avoid this, take special note of the fol- lowing. Do not connect the negative probe of the measuring equipment to REFO and GND together. It is especially important not to connect the chan

  • Pioneer DEH-P2000, 25 DEH-P2000,P20,P2050 8 CH1: TE 0.2V/div. 9 CH2: TD 0.2V/div. Normal mode: play 8 CH1: TE 0.5V/div. ! CH2: SD 0.5V/div. TEST mode: 100 Tracks jump(FWD) 5ms/div. 0 MD 0.5V/div. 0.1s/div. Normal mode: Play (12cm) 0 MD 1V/div. 10ms/div. Normal mode: Long Search (12cm) @ EFM 1V/div. 5µs/div. Normal mode: play 8 CH1: TE 1V/div. # CH2: TEC 1V/div. Test mode: Focus close Tracking open 2ms/div. 8 CH1: TE 0.5V/div. 6 CH2: FE 0.5V/div. Normal mode: AGC after focus close 0.2s/div. $ PLCK 2V/div. 0.5µs/div. Normal mode: play 20m

  • 68 DEH-P2000,P20,P2050 Basic Operation of Built-in CD Player Track Search and Fast Forward/Reverse • You can select between Track Search or Fast forward/Reverse by pressing the 2/3 button for a different length of time. Track Search 0.5 seconds or less Fast forward/Reverse Continue pressing Note: • If a disc cannot be inserted fully or playback fails, make sure the recorded side is down. P

  • Pioneer DEH-P2000, 24 DEH-P2000,P20,P2050 1 RFI 0.5V/div. 0.5µs/div. Normal mode: play 1 CH1: RFI 1V/div. 2 CH2: MIRR 5V/div. Test mode: Tracking open 0.5ms/div. 1 CH1: RFI 1V/div. 2 CH2: MIRR 5V/div. Normal mode: The defect part passes 800µm 0.5ms/div. 3 CH1: FD 0.5V/div. 4 CH2: FO+ 2V/div. Test mode: No disc, Focus close 0.2s/div. 3 CH1: FD 0.5V/div. 5 CH2: FOK 2V/div. Normal mode: Focus close 0.2s/div. 6 CH1: FE 0.5V/div. 7 CH2: XSI 2V/div. Normal mode: Focus close 1ms/div. REFO → 8 CH1: TE 0.5V/div. 9 CH2: TD 0.5V/div. Test mode: 32 tracks jump (REV) 0.5ms/div. 8 CH1: TE 0.5V/div. 9 CH2: TD 0.5V/div. Test mode: Single jump (REV)

More Instructions:

DOWNLOAD

Related Products and Documents (Car Video System):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Maytag NFW5800DW0 Installation instructions manual maytag/nfw5800dw0-5YF.pdf 04 Feb 2023 20
2 Legend L1949 Operation & user’s manual legend/l1949-RZ3.pdf 24 Jan 2023 37
3 Curtis DVD5091UK Operation & user’s manual curtis/dvd5091uk-882.pdf 25 Jun 2023 30 3.58 Mb
4 GE L60 Instruction manual ge/l60-QL2.pdf 01 Jul 2023 690
5 Sans Digital MobileStor MS4UM Operation & user’s manual sans-digital/mobilestor-ms4um-C9C.pdf 05 Dec 2023 9
6 Honeywell C7061M Product data honeywell/c7061m-V3N.pdf 29 Sep 2023 12 1.25 Mb

Similar Resources:

  • Samsung

    933BW

    (2 pages)
    933BW • 2233SW • 2233BW • 2433BW Features:• Distinctive soft design with rich piano black finish• Integrated rear cable housing for a clean look• Up to 1920 x 1080 full HD resolution (2233SW)• 5ms response, up to 20,000:1 dynamic contrast ratio• Exclusive Samsung Magic technologies for rich, natural color• Custom key for one-touch access to …
  • Sony

    CDX-M20

    (45 pages)
    SONY. FM/AM Compact Disc Player Owner's Record The model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. CDX-M20 Serial No. _______ _ To cancel the demonstration (DEMO) display, see page 6. Pou …
  • FCA US

    RADIO 3.0

    (48 pages)
    TABLE OF CONTENTSSECTION PAGE1SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93RADIO MODE . . . . . . . . . . . . . . . . . . . . . . . . …
  • JAMO

    DVR 50

    (63 pages)
    1DVR 50 - Rev. 011105-2Jamo Service manualDVR 50Rev. 011105-2DVR 50Contents To service personnel .......... 2 - 4 Faultfi nding .................... 9 Remote control ................................ 56Specifi cations ........................... 5 Audio board .................10 Cabinet ...................................... 57 - 61DVR 50 diassembly …
  • Pyle

    PLVIN72

    (2 pages)
    Type:TFT LCDDisplay size:7"Display format:16:9Power:About 7WOperation Temperature:4 60Power supply:DC 12VSystem:PAL/NTSCResolution:480(W)xR/G/Bx324(H)Overall Dimension:190(L)x182(W)x50(H)mmControl PanelPerformance ParameterWhite to video 2Yellow to video 1Green to manual brakeYellow to ACC(+12V)Red to battery +12VBlack to groundingPower switchPrecast p …
  • r.LiNK

    RL2-UCON8-SM

    (20 pages)
    Version 20.10.2020 HW: CAM(V31)/(V34) ……RL2-UCON8-SM r.LiNK Video-inserter RL2-UCON8-SM Compatible with CHRYSLER and FIAT vehicles with Uconnect 8.4N/RB5 und 8.4/RE2 and separate 8.4 inch monitor DODGE vehicles with Uconnect 8.4N/RB5, 8.4/RE2, 4.3S/REB, 4.3/RHA and separate 8.4 inch or 4.3 inch monitor Video-inserter with 2 video inputs, rear-vi …

Comments, Questions and Opinions: