Harman Kardon DRIVE + PLAY [HK-DP1EU] Owner's Manual

Text of Harman Kardon DRIVE + PLAY [HK-DP1EU] User Guide:

• INTRODUCTION Thank you for purchasing Harman Kardon’s Drive + Play™, an elegant mobile audio solution that provides the driver with easy iPod ® control, including full music browsing capability. We’ve organized this manual to make installation and operation as simple and trouble-free as possible. Please read it thoroughly before you begin installing Drive + Play. Fo

• Harman Kardon DRIVE + PLAY [HK-DP1EU], INSTALLATION Parts List Drive + Play includes the following components and parts: • Text Display With Universal Mounting Base and Attached Cable (3m) • Control Knob With 30° Mounting Base and Attached Cable (3m) • Electronics Enclosure (the Brain) • Wired FM Adapter • Removable 12-Volt Accessory Power Cable (2m) with Cigarette Lighter Adapter and In-Line Fuse Holder • Line Out Cable (1.6m): Stereo 3.5mm (M) Plug to L/R RCA (M) Plugs • iPod Cable (3m): 8-Pin Mini DIN (M) Plug to iPod Dock Connector • 0° Control Knob Base • (2) Mounting Plates for Knob Base and Display B

• Harman Kardon DRIVE + PLAY [HK-DP1EU], Electronics Enclosure Location The Electronics Enclosure contains the wireless FM transmitter and the power supply for the three components. You can install it under a seat, in the center console compartment, in the glove box or behind the radio. If possible, select a site that provides convenient access to the enclosure and easy cable routing. Also, the performance of the wireless FM transmitter depends on the location and length of the pigtail antenna. Drive + Play also provides an audio interface to a

• Direct Connection of the 12-Volt Power Harness With In-Line Fuse Holder Use this method when you want a direct connection to the vehicle’s electrical system. Leaving the in-line fuse holder intact, cut the cigarette lighter plug from the cord and strip about 4 inches of the thick, black insulation away from the three wires inside. Connect the red wire inside to the vehicle’s ACC (acc

• Harman Kardon DRIVE + PLAY [HK-DP1EU], Installing Components Installing the Electronics Enclosure At the selected site, install the Electronics Enclosure. Use either the enclosed cable ties or mounting screws, as shown below. Installing the Text Display 1. Temporarily place the Text Display at the proposed site and check the default viewing angle while adjusting the pivot arm. If it meets your needs, then skip to step 2. Otherwise, change the viewing angle as follows: a. Using the 3mm hex key, loosen the recessed hex screw (inside the display base) until the pivot arm is free from the display assembly. The hex screw will remain captive. b. Select another viewing angle position (middle or top). Reassemble the pa

• Harman Kardon DRIVE + PLAY [HK-DP1EU], b. At the proposed site, wipe the surface and exposed mounting plate with one of the enclosed alcohol pads. Allow both to dry. c. Remove the protective tape from one side of one of the enclosed adhesive pads, and press the pad against the mounting plate. d. Remove the remaining protective tape, and press and hold the Text Display to its site for 5 seconds. 4. To install the Text Display with mounting screws, perform the following steps: a. At the proposed site, place the mounting plate and rotate it so that the arrow will point toward the hex set-

• Harman Kardon DRIVE + PLAY [HK-DP1EU], Installing Components Installing the Control Knob (continued) 2. At the base (below the cable), using the 1.5mm hex key, loosen (but do not remove) the hex setscrew. 3. To install the Control Knob with adhesive tape, perform the following steps or skip to step 4: a. Insert the mounting plate, rotate it 180°, and tighten the hex setscrew. b. To ensure adhesion, wipe the surface at the site and exposed mounting plate with one of the enclosed alcohol pads. Allow both to dry. c. Remove the protective tape from one side of one of the enclosed adhesive pads, and press the pad against the mounting plate. d. R

• Harman Kardon DRIVE + PLAY [HK-DP1EU], Drive + Play operates much like the iPod itself. The Control Knob mimics the iPod’s Click Wheel, and its software uses a similar menu-select system. Before you use Drive + Play, you’ll need to set it up for the first time. After you perform the Initial Setup using the Settings Menu, controlling your iPod with Drive + Play will be easy and intuitive. To make selections on the Text Display, you simply turn the Control Knob’s Scroll Ring to highlight a desired menu item. Turn the Scroll Ring to the right to scroll down, and to the left to scroll up. Press the (center) Select button once to confirm your selection. Depending on your selection, this display may show: �

• Harman Kardon DRIVE + PLAY [HK-DP1EU], Initial Setup (continued) Setting FM Transmission (continued) • To select a Custom FM Frequency: 1. Drive + Play Menu > FM Settings > Custom Frequency. 2. The FM Frequency graphic display will appear. Scroll to select a desired FM frequency. Setting Shuffle You can set Drive + Play to shuffle (randomly play) iPod songs or albums as follows: • Drive + Play Menu > Settings > Shuffle > select Off (default), Songs or Albums. Setting Repeat You can set Drive + Play to repeat the current iPod song or all songs in a playlist or album as follows: NOTE:

• Harman Kardon DRIVE + PLAY [HK-DP1EU], Setting the Sleep Timer Drive + Play is equipped with a sleep timer that delays its power off by a default of 2 seconds after the ignition is turned off. During the delay, Drive + Play will display “powering off.” You can set a different delay time as follows: NOTE: Sleep Timer only works when the Drive + Play’s ACC wire is connected to the ignition switch’s accessory terminal (see Wiring Diagram on page 5). • Drive + Play Menu > Settings > Sleep Timer > select 2 sec (default), 4 sec, or 8 sec. Setting the Jump Size When browsing a database (songs, albums, artists, etc.),

• Harman Kardon DRIVE + PLAY [HK-DP1EU], TROUBLESHOOTING Problem: Message = iPod Disconnected Solution: • Check that the iPod Connection Cable is connected between the Electronics Enclosure and the iPod. Problem: Message = AUX is Disabled Solution: • Check AUX Input (see page 10). • Check the connection between the Electronics Enclosure and the auxiliary device. Problem: Hearing static when playing the iPod with wireless FM transmission. Solution: • Interference from an FM station at the same frequency. Try another FM frequency (see page 9). • Consider installing the optional Wired FM Transmitter (see

Related Products and Documents (Car Stereo System):

Comparable Devices:

Similar Resources:

• Alpine PXA-H600 (2 pages) Digital Phase ProcessorPXA-H600Englishß GUIDE FOR INSTALLATION AND CONNECTIONS≠ Please read this GUIDE FOR INSTALLATION AND CONNECTIONS and the OWNER'SMANUAL thoroughly to familiarize yourself with each control and function. We at ALPINEhope that your new PXA-H600 will give you many years of listening enjoyment.In case of problems when installing you …

• Rainbow Intelligence Series (20 pages) Einbauanleitung für Komponentensysteme Intelligence Line IL-C4.2 BMW E-Serie 2-Wege-Komponentensystem 80 Watt Art.-Nr. RAC231235 IL-C4.2 BMW F-Serie 2-Wege-Komponentensystem 80 Watt Art.-Nr. RAC231242 IL-C4.2 BMW Mix 2-Wege-Komponentensystem 80 Watt Art.-Nr. RAC231247 Bitte vor Beginn der Arbeiten Einbauanl …

• Philips CEM220/51 (34 pages) CEM220/51/55/98© Copyright 2009 Philips Consumer Electronics B.V. Eindhoven, The NetherlandsAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.Published by JZ-SL 0948 Service …

• Kenwood KVT-735DVD (40 pages) KVT-735DVDKVT-745DVDKVT-765DVDMONITOR WITH DVD RECEIVERINSTALLATION MANUAL附DVD接收機顯示器安裝說明書附DVD接收機顯示器安裝說明書DVD수신기장착 모니터설치설치설치설치설치 설명서설명서설명서설명서설명서© PRINTED IN JAPAN B54-4434-00/00 (M)(AI) …

• Kenwood TS-2000 (152 pages) © B62-1221-50 (K, E)09 08 07 06 05ALL MODE MULTI-BAND TRANSCEIVERTS-2000TS-2000XTS-B2000INSTRUCTION MANUALNOTIFICATIONThis equipment complies with the essential requirements of Directive 1999/5/EC.The use of the warning symbol means the equipment is subject to restrictions ofuse in certain countries.This equipment requires a licence and is intended for us …

• Kenwood KDC-105 (76 pages) Take the time to read through this instruction manual. Familiarity with installa-tion and operation procedures will help you obtain the best performance fromyour new CD-receiver.For your recordsRecord the serial number, found on the back of the unit, in the spaces designated onthe warranty card, and in the space provided below. Refer to the model and serial …

Comments, Questions and Opinions: