Pioneer TAD-CR1 Owner's Manual
|
Pioneer TAD-CR1, 2 BEFORE YOU START Thank you for buying this TAD product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. This speaker system has an impedance of 4 ' Ω , and should be connected only to an amplifier designed with a load impedance of 4 Ω (the amplifier’s speaker output connector should clearly be labeled “4 Ω ”). In order to prevent damage to the speaker system resulting from input overload, please observe the following precautions: Do not supply power to the speaker system in excess of
Pioneer TAD-CR1, 3 TAD Compact Reference TAD-CR1 SPEAKER SYSTEM Unpacking instructions 1. Cut the two packing straps on the outer carton, remove the “handle”- shaped packing joints (four places), and cut open the top fl ap. • To remove the packing joints, hold to the lever and pull outward. UP UP Straps Packing joints Top flap Tape Lever UP UP This speaker system is extremely heavy (46 kg, or 101.4 lb). Be sure to carry out unpacking and installation with at least two people. Trying to handle too much weight can throw you off balance, causing you to fall or otherwise incur bodily inju
Pioneer TAD-CR1, 4 INTRODUCTION TAD History Founded in 1975, Technical Audio Devices (TAD) has continued to stand at the frontier of cutting-edge sound technology, maintaining a well-established tradition of creating high performance speakers for professional use. TAD products are designed, crafted, and produced with strict adherence to the most rigorous standards demanded by musicians and professional audio-system designers around the world. TAD loudspeaker components are found in studio monitors, sound reinforcement sy
Pioneer TAD-CR1, 5 TECHNOLOGY Beryllium Diaphragms Each TAD Compact Reference speaker system features proprietary beryllium-manufacturing technology for the midrange and tweeter diaphragms. The lightest and most rigid metal available for diaphragms, beryllium performs with strength and damping characteristics unmatched by any of the materials currently used in high-end audio loudspeaker manufacturing, as shown in Figure 1. Beryllium’s combination of light weight and exceptional strength enables diaphragm resonance to b
Pioneer TAD-CR1, 6 Bass Driver The foundation of the TAD Compact Reference speaker syatem is the bass driver, as shown in Figure 3. The driver cone is constructed from a tri-laminate of front and rear-woven aramid fibers that sandwich a foamed acrylic core. This provides enormous strength to the cone in order to resist any flexing due to the high forces exerted during loud bass passages. To achieve high drive linearity, the motor structure employs short coil, long-gap geometry, Faraday shorting rings and a novel flux path design. The speaker also features a newly designed spider and multi-roll surround for the best possib
Pioneer TAD-CR1, 7 CST Mounting Construction The CST driver is mounted into an extremely rigid enclosure that features a baffle specially formed to optimize the sound emitted from the driver. To further enhance the performance, ISO-Drive technology is used to mechanically isolate the CST driver from its cabinet. This greatly reduces the mechanical energy that is the source for enclosure vibration, resulting in reduced delayed resonances and improved resolution of fine detail. Bass Enclosure Construction The enclosure of the TAD Compact Reference’s bass driver features a frame of 21 mm (0.9 in.) thick laminated birch plywood supported by a CNC processed plywood back board “spine” up to
Pioneer TAD-CR1, 8 INSTALLATION AND PLACEMENT Precautions during installation This speaker system has a total weight of 46 kg ' (101.4 lbs). Be sure that the installation location has a surface fully capable of supporting this weight. Further, when using the spikes, each spike will bear ' a load exceeding 15 kg (33 lbs), potentially leading to the production of marks or depressions in the surface contacted by the spike. In order to avoid such damage, either use the supplied spike bases, or other spike base material with the strength and sufficiently large area to support the spike safely. When spikes are used with
Pioneer TAD-CR1, 9 Installing The Spikes The use of spikes on the bottom of the speaker system allows the creation of a secure contact between the speaker cabinet and the installation surface. The base of the speaker cabinet is provided with three points for the installation of the spikes. By supporting the speaker at these three points, secure contact can be established between the speaker and installation surface without the need for adjusting the height of the spikes. See Choosing Where To Place The Speakers on page 10 for help deciding where to place the speake
Pioneer TAD-CR1, 10 Choosing Where To Place The Speakers Speaker placement within the listening room will have a great impact upon the total performance of TAD Compact Reference speaker system in terms of bass performance, tonal accuracy, and imaging. All rooms are different and so this section is intended as a guide only. Experimentation in your room will yield optimum results. Begin by placing the rear of the speakers approximately one to two feet in from the front walls and the sides one to two feet in from the side walls of your listening room, as shown in Figure 6. Your listening position should be roughly equa
11 CONNECTING THE SPEAKERS CAUTION When connecting speakers or other components, always turn off the power to the amplifier, and disconnect the power cord. ' Speaker cables are not furnished with this speaker system, and must be purchased separately. ' Single-Wire Connections For single-wire connections, connect the high- and low-frequency sections of t
Pioneer TAD-CR1, 12 Bi-Wire Connections In a bi-wiring connection, you independently plug in the loudspeakers running from the amp to their respective high- and low-frequency plugs. This results in the CST driver and bass driver being independently connected directly to the amplifier, offering you the freedom to optimize the cable type for each of the drivers. Connect one set of wires to the bottom set of binding posts (bass driver-specific network). Then connect a second set of wires to the top binding posts (CST-specific network). Next, connect
13 Bi-Amplification Connections Bi-Amplification allows the best performance from the TAD Compact Reference speaker system by using dedicated amplifiers for low- and high-frequency sections. There are two possible configurations, commonly referred to as horizontal and vertical bi-amping. WARNING Remove the shorting links before connecting speaker cables in bi-ampli
14 Horizontal Bi-Amping With this configuration, you may use different stereo amplifiers for the low- and high-frequency sections of the speaker system (e.g., tube amplifiers for high frequency and solid state for low frequency). Each channel of one amplifier drives the low-frequency section of each speaker and each channel of the other amplifier drives the high-frequency secti
Pioneer TAD-CR1, 15 OPTIMIZING THE SYSTEM Improving Bass Performance Select a music track with well-recorded bass, such as acoustic string bass. Listen for all the bass notes having roughly equal level. If any notes jump out at you more strongly than others, try moving the TAD Compact Reference speaker system until you get the most even progression of the notes. Typically, moving them towards the walls will increase low bass output, but can result in more unevenness higher up the musical scale. Moving them closer to the side walls will not produce the same effect as moving closer to the back wall, so try experimenting moving both ways for the most pleasing sound. Also listen to drum sounds. Th
Pioneer TAD-CR1, 16 SPEAKER CARE Each TAD Compact Reference speaker system has a polymer finish that requires care similar to a grand piano. For accumulated dust and fingerprints, simply wipe the cabinet with the included cleaning cloth. CAUTION Do not use any cleaners or polishes on the cabinet or grille! ' In areas of high humidity, use a dehumidifier, and in areas of excessive dryness, use a humidifier to adjust the room’s humidity level. Avoid exposure to direct sunlight, and do not install in areas
Pioneer TAD-CR1, 17 SPECIFICATIONS Model Name TAD Compact Reference Model No. TAD-CR1 Design Bass reflex, bookshelf-type speaker Drive units Bass driver ............................................................ 20 cm (8 in.) cone Midrange/Tweeter ............................................................. concentric 16 cm (6 1/2 in.) cone/ 3.5 cm (1 3/8 in.) dome Performance Data Frequency Range ..................................... 32 Hz to 100 kHz (–10 dB) 40 Hz to 20 kHz, ±3 dB; frontal average response Crossover Frequen
18 Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by play
Pioneer TAD-CR1, <SRB1342-B> Printed in China TECHNICAL AUDIO DEVICES LABORATORIES, INC. 4-15-3 Nishi-Shinjuku Shinjuku-ku, Tokyo 160-0023, Japan Published by Pioneer Corporation. Copyright © 2009 TECHNICAL AUDIO DEVICES LABORATORIES, INC. All rights reserved.
DOWNLOAD |
Pioneer SP-BS22-LR Speaker System Spesification
SP-BS22-LR |
Pioneer S-3EX Speaker System Operating instructions manual
S-3EX |
Pioneer XR-A790 Speaker System Operating instructions manual
XR-A790 |
Pioneer PDP-S37 Speaker System Operating instructions manual
PDP-S37 |
Pioneer HPM-100 Speaker System Service manual
HPM-100 |
Pioneer XC-L77(DU-L77) Speaker System Operating instruction
XC-L77(DU-L77) |
Pioneer S-3EX Speaker System Operating instructions
S-3EX |
Pioneer XV-DV77 Speaker System Operating instructions manual
XV-DV77 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Philips | HD2618 | Operation & user’s manual | philips/hd2618-461.pdf | 09 Jul 2023 | 7 | |
2 | Yamaha | RX-1130 | Owner's manual | yamaha/rx-1130-9QI.pdf | 23 Nov 2022 | 28 | 2.68 Mb |
3 | ViewSonic | VE702m | Operation & user’s manual | viewsonic/ve702m-3K3.pdf | 10 Aug 2022 | 16 | 0.41 Mb |
4 | Memorex | RF Optical Mouse | Operation & user’s manual | memorex/rf-optical-mouse-7F5.pdf | 18 Aug 2023 | 6 | |
5 | Metz | Axio pro | Operating instructions manual | metz/axio-pro-11S.pdf | 14 Oct 2022 | 148 | |
6 | Weber | 310 | Assembly instructions | weber/310-1JZ.pdf | 30 Nov 2023 | 4 | 7.71 Mb |
Sun Microsystems
Sun Microsystems, Inc.901 San Antonio RoadPalo Alto, CA 94303-4900 U.S.A.650-960-1300Send comments about this document to: [email protected] StorEdge™T3 and T3+ ArrayConfiguration GuidePart No. 816-0777-10August 2001, Revision A
…
Sun StorEdge T3(88 pages) |
Ground Zero
Die Gewährleistung entspricht der gesetzlichen Regelung. Eine Rücksendung kann nur nach vorheriger Absprache und in der Originalverpackung erfolgen. Bitte unbedingt einen maschinell erstellten Kaufbeleg und eine Fehlerbeschreibung beilegen. Von der Gewährleistung ausgeschlossen sind Defekte, die durch Überlastung, unsachgemäße Behandlung oder b …
IRIDIUM SERIES(4 pages) |
Sony
SS-CN550H Center Channel Speaker Key FeaturesCenter Channel SpeakerEnhanced HOP Dual 5 1/4" Drivers with 1" TweeterNano-Fine® Balanced Dome Tweeter Rated to 50 kHz150W Maximum Power Handling (Center)8 ohm Speaker ImpedanceSupplied Speaker Cables and Protective FeetKey Technologies150W Maximum Power Handling (Center) 8 ohm Speaker Impedance Cen …
SS-CN550H(2 pages) |
Sony
SRS-TP1_U,CA (US/FR/ES) 3-100-971-13(1)© 2007 Sony Corporation Printed in ThailandStereo SpeakerSystemSRS-TP13-100-971-13(1)Operating InstructionsMode d’emploiManual de instrucciones EnglishBefore operating the unit, please read this manual thoroughly and retain itfor future reference.WARNINGTo reduce the risk of fire or electric shock, do not expos …
SRS-TP1(2 pages) |
Monacor
MCX-10Best.-Nr. 24.7030Elektronische FrequenzweicheEinsatzmöglichkeitenDie aktive 2-Wege-Stereo-Frequenzweiche MCX-10 ermöglicht dieAufteilung des Frequenzbereiches bei Subwoofer/Satellitenlaut-sprecher-Audiosystemen und läßt sich sowohl für professionelleZwecke (z. B. Bühne, Disco) als auch im Heimbereich einsetzen.Hinweise für den sicheren GebrauchD …
IMG Stageline MCX-10(5 pages) |
Onkyo
EnEnjoying Home TheaterThe Home Theater means that you can enjoy surround sound with a real sense of movement in your own home — just like being in a movie theater or concert hall.Connecting the SpeakersFront left and right speakers (SKF-980) They should be positioned facing the listener at about ear level, and equally spaced from the TV. Angle them inward …
HTP-980(2 pages) |
Telex Intercom System RVON-IUser Guide: Telex RVON-I (X4S22A, Upd.Thu 02.2024) RVON-I, 40 |
Motorola Baby Monitor MBP994CONNECTMBP994CONNECT Operation & user’s manual - KKLTV8 MBP994CONNECT, 57 |
Nikon Camera Lens f/2.8D EDPDF User Manual (@B9ZP7M), Nikon f/2.8D ED Camera Lens (03/12/2023) f/2.8D ED, 2 |
Rollei Camera Accessories Beta 180Beta 180 Operation & user’s manual - YW2824 Beta 180, 36 |
Emerson Switch Rosemount 2511Quick start manual for Emerson Rosemount 2511 Switch Rosemount 2511, 24 |
Schneider Airsystems Compressor UGL MASSchneider Airsystems UGL MAS User Manual (Doc Type: Compressor Assembly instructions manual) UGL MAS, 8 |
Pioneer Monitor AVH-P6600DVDPioneer AVH-P6600DVD User Manual (Installation manual), @JO4219 AVH-P6600DVD, 85 |
MTX Car Amplifier TC3001Guide: MTX TC3001 (78OST2, Upd.04th Feb 2024) TC3001, 17 |
Tripp Lite Surge Protector TLP82D#2T5319: TLP82D Surge Protector Specifications TLP82D, 2 |
Opex Digital Mailing system OMATION 2112OMATION 2112 (Digital Mailing system ePDF User Manual, #I7TJVI) OMATION 2112, 14 |
Exibel Receiver DABX30CDABX30C Instruction manual - 5ORDQ4 DABX30C, 28 |
Weider Other Platinum XP600Manual: Weider Platinum XP600 (6UZ82I, Upd.Friday 02-02-2024) Platinum XP600, 27 |