Manualios.com

Toshiba NetPac Installation And Operation Manual

Toshiba NetPac Manual Online:

3.75, 1148 votes
Toshiba NetPac User Manual
Toshiba NetPac User Guide
Toshiba NetPac Online Manual

Text of Toshiba NetPac User Guide:

  • Toshiba NetPac, NetPac Wireless System 11 Software Installation and Verification The Toshiba NetPac Wireless System software is to be used for system setup only. Consult the ASD PRO Software Manual for specifics on the operation of the ASD PRO software. Driver/Port Installation and Setup Proper system operation requires that two components be loaded onto the host PC: Driver information and Port information. Note: Both components must be loaded completely. Failure to load both components completely may result in an unexpected motor response, intermittent operation, or total system failure. Follow steps 1 through 7 below to load the driver information.

  • Toshiba NetPac, NetPac Wireless System 7 Hardware Installation • The system hardware components are to be installed by Qualified Personnel only. •The Toshiba NetPac Wireless System is designed for use in Toshiba’s 7-Series and 9-Series ASDs only. DO NOT attempt to install the wireless components in any other type of system, as this may result in equipment damage or injury to personnel. • Bent pins or an improper insertion may result in intermittent operation or system failure. • Apply power to the ASD only after attaching and/or securing the front cover (ASD dependent) of the ASD. Software Installation • The system software is to be installe

  • Toshiba NetPac, About This Guide This guide was written by the Toshiba Technical Publications Group. This group is tasked with providing technical documentation for the Toshiba NetPac Wireless System. Every effort has been made to provide accurate and concise information to you, our customer. At Toshiba we’re continuously searching for better ways to meet the constantly changing needs of our customers. E-mail your comments, questions, or concerns about this publication to [email protected]. Guide’s Purpose and Scope This guide provides i

  • Toshiba NetPac, NetPac Wireless System 1 General Safety Information DO NOT attempt to install, operate, or dispose of this equipment until you have read and understood all of the product safety information and directions that are contained in this guide. Safety Alert Symbol The Safety Alert Symbol is comprised of an equilateral triangle enclosing an exclamation mark and indicates that a potential personal injury hazard exists. Signal Words Listed below are the signal words that are used throughout this guide followed by their descriptions and associated symbols. When the words DANGER, WARNING, or CAUTION are used in this guide they will be followed by important safety informat

  • Toshiba NetPac, 12 NetPac Wireless System Figure 1. New Hardware Wizard. 3. Browse to the CD ROM drive and select the folder (driver) of the operating system being used (i.e., Vista, XP, etc.) and click Next (see Figure 2.). Note: If the PC operating system is unknown, right- click the My Computer icon of the PC desktop and select Properties. The General tab will show the operating system type being used. Toshiba Inter. Corp. USB to NetPac

  • Table of Contents NetPac Wireless System i General Safety Information .......................................... 1 Safety Alert Symbol ................................................. 1 Signal Words ............................................................ 1 Special Symbols .............................................................. 3 Electrical Hazard

  • Toshiba NetPac, 4 NetPac Wireless System may result in serious injury, severe property and equipment damage, or loss of life if safe procedures or methods are not followed as outlined in this guide. Qualified Personnel Installation, operation, maintenance, and disposal are to be performed by Qualified Personnel only. A qualified person is one that has the skills and knowledge relating to the construction, installation, operation, and maintenance of the electrical equipment and has received safety training on the hazards involved (refer to the latest edition of NFPA

  • Toshiba NetPac, 14 NetPac Wireless System 7. Repeat the procedure once from step 2 on page 11 to load the port information. Driver/Port Installation and Setup are complete upon the completion of the second execution of step 6 above.

  • 18 NetPac Wireless System ASD PRO Software The ASD PRO Software allows the user to monitor and control the ASD from a PC via serial communication. A free copy of the ASD PRO Software and the ASD PRO Software Installation and Operation Manual may be downloaded from web site www.toshiba.com/ind. 1. From the www.toshiba.com/ind web site click Industrial Divi

  • Toshiba NetPac, TOSHIBA is a registered trademark of Toshiba Corporation. All other product or trade references appearing in this guide are registered trademarks of their respective owners. All rights reserved. Printed in the U.S.A. Contacting Toshiba’s Customer Support Center Toshiba’s Customer Support Center can be contacted to obtain help in resolving any Adjustable Speed Drive system problem that you may experience or to provide application information. The Support Center is open from 8 a.m. to 5 p.m. (CST), Monday through F

  • 2 NetPac Wireless System The word CAUTION preceded by the safety alert symbol indicates that a potentially hazardous situation exists that, if not avoided or if instructions are not followed precisely, may result in minor or moderate injury. The word CAUTION without the safety alert symbol indicates a potentially hazardous situation exists that, if not avoided or if in

  • Toshiba NetPac, NetPac Wireless System 15 USB Driver/Port Verification 1. From the PC desktop, right click the My Computer icon and select Properties from the subsequent list. 2. At the System Properties dialog box, click the Hardware tab (see Figure 4.). Figure 4. System Properties Dialog Box. 3. Click the Device Manager button. 4. At the Device Manager dialog box expand the Universal Serial Bus Controllers folder. The Toshiba Inter. Corp. USB to NetPac file being listed is an indication of a successful driver load. 5. At the Device Manager dialog box expand the Port (COM & LPT) folder. The Toshiba

  • Toshiba NetPac, TOSHIBA TOSHIBA INTERNATIONAL CORPORATION INDUSTRIAL DIVISION 13131 West Little York Road, Houston, TX 77041-5807 US (800) 231-1412 CAN (800) 872-2192 MEX 01 (800) 527-1204 FAX: (713) 466-8773 http://www.toshiba.com/ind/ Printed in the U.S.A.

  • Toshiba NetPac, NetPac Wireless System 5 • Carefully unpack the equipment and check for damaged parts, missing parts, or concealed damage that may have occurred during shipping. If any discrepancies are discovered, it should be noted with the carrier prior to accepting the shipment, if possible. File a claim with the carrier if necessary and immediately notify your Toshiba Sales Representative. • DO NOT install equipment if it is damaged or if it is missing any component(s). • Modification of this equipment is dangerous and is to be performed by factory trained personnel.

  • Toshiba NetPac, 16 NetPac Wireless System 6. Close the Device Manager. 7. Close the System Properties dialog box. The USB/COM port is installed successfully and is ready for use. In the event that Toshiba Inter. Corp. USB to NetPac does not appear as a folder item, contact the Toshiba Customer Support Center for assistance.

  • Toshiba NetPac, Introduction Congratulations on the purchase of the Toshi ba Ne tPac Wireless System! The Toshiba NetPac Wireless System is a communications solution that is designed to monitor and control a network of Toshiba’s 7-Series and 9-Series Adjustable Speed Drives (ASDs). The wireless system consists of three components: a USB Transceiver Module, an ASD Transceiver Module (one for each ASD within the network), and the software CD. The USB Transceiver Module communicates with the ASD Transceiver Module. The USB module connects to the USB port of the PC that will be used for system monitoring and control via the ASD PRO Software

  • Toshiba NetPac, NetPac Wireless System 9 orientation and that all mating pins are seated fully and uniformly. 5. Insert the Series-2 Module (P/N 64709) into the Adapter Board — ensure that the module is inserted with the correct orientation and that all mating pins are seated fully and uniformly. 6. Close the front door or reattach the front cover (device- specific). 7. Apply system/ASD power. Note: CNU1 of the control board CANNOT be used while using the Toshiba NetPac Wireless System. RJ-45 Transceiver Installation 1. Perform steps 1 and 2 of the Series-2 Transceiver Module Installation on page 8. 2. Insert the transceiver module into the RJ-45 connector of the 7-Se

  • Toshiba NetPac, 6 NetPac Wireless System Installation Precautions Personnel Protection •The Toshiba NetPac Wireless System is to be installed, operated, and disposed of by Qualified Personnel only. • Personal protection equipment is to be used to protect employees from any hazards inherent to system operation. • Follow all warnings and precautions. Power Connections Contact With Energized Wiring Will Cause Severe Injury Or Loss Of Life. • Turn off, lockout, and tagout all power sources before performing maintenance and making adjustments to the ASD system. • Ensure that all system/ASD power is off and that the Power and Charge LEDs on the ASD are off before opening the front doo

  • NetPac Wireless System 3 Special Symbols To identify special hazards, other symbols may appear in conjunction with the DANGER, WARNING, or CAUTION signal words. These symbols indicate areas that require special and/or strict adherence to the procedures to prevent serious injury to personnel or loss of life. Electrical Hazard Symbol The Electrical Hazard Symbo

  • Toshiba NetPac, 8 NetPac Wireless System Hardware Installation and Connections Contact With Energized Wiring Will Cause Severe Injury Or Loss Of Life. There are two types of transceiver modules used with the 7-Series ASD. The Series-2 (shown below) is used with the 7-Series ASD only and the RJ-45 type (shown on page 9) is used with the 7- and 9-Series ASD. Series-2 Transceiver Module Installation 1. Ensure that all system/ASD power is off and that the ASD Power and Charge LEDs are off. 2. Open the front door or remove the front cover (device- specific) of the ASD to gain access to the control board of the ASD. 3. R

  • Toshiba NetPac, NetPac Wireless System 13 Figure 2. Driver Selection. 4. In the event that the Software Compatibility prompt appears, click Continue Anyway. 5. In the event that the Files Needed dialog box appears, browse to the required file(s) of the CD ROM drive and click OK. Figure 3. Files Needed Dialog Box. 6. Upon completion of the installation the Found New Hardware Wizard Completion dialog box appears — Click Finish.

  • Toshiba NetPac, NetPac Wireless System 19 Index Numerics 2-Wire Operation , 17 4-Wire Operation , 17 7-Series ASD Transceiver Mod- ule Installation , 8 A Adapter Board , 8 ASD PRO Software , 18 C Charge LED , 6, 8 CNU1 , 9 D Disposal , 5 Driver Installation , 11 Driver/Port Verification , 15 E Electrical Hazard Symbol , 3 Equipment Inspection , 4 Equipment Warning Labels , 3 Explosion Hazard Symbol , 3 G General Safety Information , 1 H Hardware Installation , 7 I Installation Precautions , 6 J Jumper PCB , 8 P Personnel Protection , 6 Port Installation , 11 Port Verification , 15 Power Connections , 6 Power LED , 6, 8 Q Qualifie

Related Products and Documents (Transceiver):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Adaptec 2045 Datasheet adaptec/2045-3EY.pdf 08 May 2023 2 1.07 Mb
2 Miles Industries 1800JN Owner's manual miles-industries/1800jn-931.pdf 10 Jun 2023 68
3 Supermicro 6021H Operation & user’s manual supermicro/6021h-1KW.pdf 08 Nov 2022 112
4 Airlink101 AWLL3055 Operation & user’s manual airlink101/awll3055-V5S.pdf 14 Sep 2022 27 1.1 Mb
5 Aquatic AQ-CD-3 Specifications aquatic/aq-cd-3-X2P.pdf 28 Aug 2022 1 0.94 Mb
6 Sony DVP-F11 Operating instructions manual sony/dvp-f11-NTH.pdf 14 Jul 2023 68 0.87 Mb

Similar Resources:

  • ADTRAN

    T200 FNID

    (28 pages)
    Section 61223024L2-5AIssue 1, December 2003CLEI Code: T1L7TDHA_ _61223024L2-5A 1Trademarks: Any brand names and product names included in this document are trademarks, registered trademarks, or trade names of their respective holders.CONTENTS1. General................................................................ 12. Installation ...................... …
  • QRP Labs

    QCX

    (25 pages)
    Page 1 of 25 QCX Troubleshooting I have fixed several QCX kits. The following describes my fault-finding procedure. You can follow these steps too. Even if your QCX radio works perfectly, signal tracing through the circuit as described on this page, is a very educational experience! You will find you get a greater and deeper understanding of how the QCX wo …
  • Kenwood

    TK-2317 M3

    (52 pages)
    SERVICE MANUALThis product complies with the RoHS directive for the European market.This product uses Lead Free solder.© 2011-4 PRINTED IN JA PANB51-8972-00 (Y) PDFVHF FM TRANSCEIVERTK-2317CONTENTSGENERAL ....................................................2SYSTEM SET-UP .........................................3REALIGNMENT ................................. …
  • Dynon Avionics

    DX15 

    (30 pages)
    Rhein Tech Laboratories, Inc. Client: Dynon Avionics Inc. 360 Herndon Parkway Model: DX15 Suite 1400 FCC ID: WU6-101204-000 Herndon, VA 20170 Standard: FCC Part 87 http://www.rheintech.com Report #: 2009191 Appendix J: Manual Please refer to the following pages. …
  • Vertex Standard

    VX-1210

    (76 pages)
    1VX-1210Service ManualIntroductionThis manual provides technical information necessary for servicing the VX-1210 Transceiver.Servicing this equipment requires expertise in handling surface-mount chip components. Attempts by non-qualified persons toservice this equipment may result in permanent damage not covered by the warranty, and may be illegal in some co …
  • Icom

    ic-2300H

    (41 pages)
    SERVICE MANUAL ADDENDUM CONTENTS PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 BOARD LAYOUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 VOLTAGE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . 8Feb. 2012 …

Comments, Questions and Opinions: