B2B EL-26MC2RE Operation & User’s Manual

Text of B2B EL-26MC2RE User Guide:

• CCTV LCD Monitor User Manual For models: EL-26MC2RE EL-32MC2RE EL-42MC2RE

• 3 " “ Power : Press button to turn the power on and press again to turn the power off. 4 .” ” Up/Increase : To move the cursor upwards or to switch over the setting items or to increase the figure of the setting Selected 5 “Menu/Enter” : To enter the OSD menu or confirm the

• B2B EL-26MC2RE, the colored wires of the mains lead of this appliance do not correspond with the colored markings identifying the terminals in your plug, proceed as follows: The wire which is colored GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the Earth symbol or colored GREEN or GREEN-AND-YELLOW. The wire which is colored BLUE must be connected to the terminal in the plug which is marked with the letter N or colored BLACK. The wire which is colored BROWN must be connected to the terminal in the plug which is marked with the

• B2B EL-26MC2RE, 2 Work Safety Information Caution and Warning CAUTION !! RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No internal parts can be serviced by users. Refer servicing to qualified personnel. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS CCTV LCD MONITOR TO RAIN OR MOISTURE. “HIGH VOLTAGE EXISTS ON THE BACK LIGHT POWER LEAD OF THIS CCTV LCD MONITOR. BEFORE SERVICING, DETERMINE THE PRESENCE OF HIGH VOLTAGE BY CONNECTING THE H.V. METER BETWEEN THE BACK LIGHT POWER LEAD AND CHASSIS ONLY“

• B2B EL-26MC2RE, 4. Hardware This chapter will guide you through the correct installation procedures for the LCD monitor. 4.1. Checking the Accessories Supplied  LCD monitor body x 1 pc  Desk Stand x 1 pc  AC power cord x 1 pc  D-Sub 15-pin cable (1.8 Meter) x 1 pc  Ø 3.5mm audio line (1.5 Meter) x 1 pc  User manual (CD) x 1 pc  Remote Controller x 1 pc  Battery (AAA) x 2 pcs 5. Buttons

• B2B EL-26MC2RE, 3. Over Scan-H The format is the over scan mode that provide a 4:3 format that will create a black bar on both right and left of frame. 4. Over Scan-1 The format is over scan mode to make the image fill up the 16:9 screen and cut about 3% on both “Vertical” and “Horizontal” lines. 5. Over Scan-2 The format is another over scan mode to make the image fill up the16:9 screen and cut about 6% on both “Vertical” and “Horizontal” lines. OSD Time

• B2B EL-26MC2RE, 3 Standards and Guidelines 3.1 FCC Requirements This device complies with Part 15 of the FCC Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must tolerate any interference encountered, including interference that may cause improper operation. The equipment has been tested and found to comply with the requirements stipulated in Part 15 of FCC regulations for a Class B digital device. These requirements are designed to provide reasonable protection against harmful interf

• B2B EL-26MC2RE, 10. Technical Data Model EL - 26MC 2 RE EL - 32MC 2 RE EL - 42MC 2 RE System Panel Size 26" LCD 32" LCD 42" LCD Backlight LED, 60Hz LED, 60Hz LED, 60Hz Resolution 1920 x 1080 1920 x 1080 1920 x 1080 Pixel Pitch (H xV) 0.3(H) x 0.3(V) mm 0.36375(H) x 0.36375(V) 0.4845(H) x 0.4845(V) Contrast Ratio 1000:1 4000:1 4000:1 Luminance 400 cd/m2 400 cd/m2 400 cd/m2 Aspect Ratio 16:9 16:9 16:9 Response Time Grey to Grey =8 ms Grey to Grey =6.5 ms Grey to Grey =6.5 ms View Angel U/D: 89/89 , L/R: 89/89 U/D: 89/89 , L/R: 89/89 U/D:89/89, L/R:89/89 Video Signal Analog RGB Signal , 8 bit LVDS,

• B2B EL-26MC2RE, Backlight Press “ to select “ High / Medium / Low / Min “ to adjust backlight. “High” level will make the backlight in most high light, the “Min” will minimize the backlight. Color Temp. Select the Color Temp.” for white balance. Press “Menu/Enter” to enter color temp. option. There are 4 settings to choose from (1)Standard (2). Warm (3).Cold (4) User. To select “User” you may press “ to increase/decrease the “Pink bar” to adjust color of Red, Green and Blue. Sound Effect (Video/HDMI

• B2B EL-26MC2RE, Main Screen Press the “Menu/Enter” key to enter the Main Screen and press “ to select VGA as the main screen . When the main screen is in VGA mode, the sub screen can be Video-1/ S-Video/ HDMI. But when select Video-1/ S-Video/ HDMI as main screen, the sub screen will be VGA only. Sub Screen Press the “Menu/Enter” key to enter the Sub Screen and press “ to select VGA as the sub- screen . When the main screen is in VGA mode, the sub screen can be Video-1/ S-Video/ HDMI. Sub Size Press the “Menu/Enter” key to enter the Sub Size and press “ to select the size

• B2B EL-26MC2RE, 9. Unplug this product from the wall outlet and refer servicing to qualified service personnel in the event that: - Liquid is spilled onto the product or the product is exposed to rain or water. - The product does not operate normally when the operating instructions are followed. - The product has been dropped or the cabinet has been damaged. - The product exhibits a distinct change in performance, indicating a need for service. - The power cord or plug is frayed or damaged. - Has referred to Troubleshooting Tips and problems still

• B2B EL-26MC2RE, Function (Video/HDMI Mode) 1. Press the “Menu/Enter” key on the buttons to call out the OSD “Menu” . Press “ to select “Function” Mode and press “Menu/Enter” key again to select the “Function” option. 2. Various function settings are available from the “Function” menu. Use“ to select item that you want to adjust and press “Menu/Enter” key again until yellow bar changes to pink bar and press “ increase or decrease the figure that you wish . Press “Exit” key to return to menu and confirm the setting. Press two times of “Exit” to

• B2B EL-26MC2RE, 6. ID Remote Controller  . POWER switch. Press to turn ON or turn OFF the LCD Monitor. . VIDEO SIGNAL Selection: Press the “AV1” , “S-VIDEO”, “D-SUB”, “HDMI” , button to enter the selected video source or press the “SOURCE” button to have the cycle video selection.

• B2B EL-26MC2RE, Image Mode(HDMI-PC) When HDMI as the PC interface, there are 2 image ratio to choose (1) Full (2) 4:3 Press “ key to select the format you want. 1. Full The image fully fills up the 16:9 screen on both “Vertical” and “ Horizontal” lines to provide a true 16:9 format. 2. 4:3 The format is the under scan mode that provide a 4:3 format and there will be a black bar on both right and left of frame. Multi Screen (VGA Mode) The setup is the same as page No. 17 for Multi Screen setup of “Video/HDMI Mode”.

• B2B EL-26MC2RE, 2.3.1 For the United States and Canada In the United States and Canada the male plug is a NEMA5-15 style (Figure A2, above), UL Listed, and CSA Labeled. For units which are mounted on a desk or table, SVT or SJT type cord sets may be used. For units which sit on the floor, only SJT type cord sets may be used. The cord set must be selected according to the current rating for your unit. Please consult the table below for the selection criteria for power cords used in the United States and Canada. Code Type Size of Conductors in Cord Maximum Current Rating of Unit SJT 18 AWG 16 AWG 14 AWG 10 Amps 12

• B2B EL-26MC2RE, 3.Over Scan-H The format is the over scan mode that provide a true 4:3 format that will create a black bar on both right and left of frame. 4. Over Scan-1 The format is over scan mode to make the image fill up the 16:9 screen and cut about 3% on both “Vertical” and “Horizontal” lines. 5. Over Scan-2 The format is another over scan mode to make the image fill up the16:9 screen and cut about 6% on both “Vertical” and “Horizontal” lines. Image Mode (HDMI mode) When HDMI as the video interface, there are 5 image ratio to choose (1) Full Scan (2) Under Scan-V (3). Over Scan-H

• 7. OSD Setup Picture (Video / HDMI Mode) 1. Press the “Menu/Enter” key on the buttons to call out the OSD“ Menu” . Press “ to select “Picture” mode and press “Menu/Enter” key again to access into item option . Press “ to select item you want to adjust. 2. Various picture settings are available from the “Picture�

• 1 Introduction Thank you for purchasing the professional CCTV LCD Monitor and welcome to a fantastic new technology that will completely change the way you look at monitors. The following sections describe just a few of the major advantages of this LCD monitor. You’ll discover more of its wonderful features as you use it. Please note that this manual

• Key Lock The function is to prevent from the kid’s playing or mis-press to change the setting. Press “Menu/Enter” and select “Yes” to activate the key lock function, select “No” will close the key lock function. If you want to release the Key Lock function you can press “Menu/Enter” and “Source/Exit” key simultaneously. Anti Burn-in The function can prevent the L

• B2B EL-26MC2RE, Contrast Press “ to increase/decrease the “Pink bar” to adjust contrast. Increasing contrast will make white area of the video picture brighter. Contrast works in conjunction with “Brightness”. Brightness Press“ to increase/decrease the “Pink bar” to adjust brightness. Adjusting brightness to enhance the level of dark area in the video picture such as night scenes and shadow scenes. Increasing brightness will make dark areas more visible. Backlight Press “ to select “ High / Medium / Low / Min “ to adjust backlight. “High” level will make

• B2B EL-26MC2RE, 3.3 CE Conformity The device complies with the requirements of the directive 2004/108/EC with regard to “Electromagnetic compatibility”. 3.4 RoHS Compliance Statement This display defined in this user manual is 100% RoHS complaint and meets all the requirements set forth in European Union Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment. 3.5 Information on Disposal for Your Old Product Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment, recove

• B2B EL-26MC2RE, Sound Effect (VGA Mode) The setup is the same as page No.13 for sound setup of “Video/HDMI Mode”. Function (VGA Mode) The setup is the same as page 14 for Function adjustment of “Video/HDMI Mode”. Image Mode(VGA Mode) When the signal is in VGA mode, there are 2 image ratio to choose (1) Full Scan (2) 4:3 Press “ key to select the format you want. 1. Full Scan The image fully fills up the 16:9 screen on both “Vertical” and “ Horizontal” lines.

• B2B EL-26MC2RE, 9. Applicable Video Timing for PC- analog Video The following table list are the better display quality modes for analogy signal (PC) supported by this LCD monitor. The LCD monitor will stop working or has poor picture quality when other modes out of below list input. VGA Mode timing : Note : 1360 x 768 for D-sub mode only HDMI Mode Timing:

Related Products and Documents (Monitor):

Comparable Devices:

Similar Resources:

• LG W2453 Q Series (26 pages) Make sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference.See the label attached on the product and give the information to yourdealer when you ask for service.W2453VUser’s GuideW2453*Q …

• CTX EX1200 (14 pages) English8188♦♦♦1EnglishTABLE OF CONTENTSSAFETY INSTRUCTIONS ................................................................. 2INTRODUCTION ............................................................................ 4Package Contents .................................................................... 4Feature Highlights ............................... …

• Mitsubishi Electric SD420U (84 pages) CAUTIONBefore servicing this chassis, it is important that the service person read the “SAFETY PRECAUTIONS” and “PRODUCTSAFETY NOTICE” in this service manual.Pb Solder, Pb Joints, Pb PCAThis product uses lead-free solderon the circuit boards. For repairingcircuit boards, see "Precautions forresoldering" in this Service Manual.These mode …

• Samsung DC43H (133 pages) User ManualThe colour and the appearance may differ depending on the product, and the specications are subject to change without prior notice to improve the performance.Recommended hours of use per day of this product is under 16 hours.If the product is used for longer than 16 hours a day, the warranty may be void.DCH (DC43H DC49H DC55H)DCJ (DC43J DC49J) …

• Tatung TME19WA (27 pages) USER’S MANUAL TFT LCD MONITOR MODEL: TME19WA/TME22WA www.tatungusa.com …

• AG Neovo RX-W19 (2 pages) NeoV™ Optical Glass - e most trusted hard glass protection available. Only on AG Neovo displaysREACHwww.agneovo.comRX-W19A durable 19” widescreen display with hard glass protection, image burn-in prevention and other essential features required in modern surveillance environments.Specically designed and tested for commercial video security applicat …

Comments, Questions and Opinions: