Manualios.com

3M G5 Installation Manual

3M G5 Manual Online:

3.5, 1511 votes
3M G5 User Manual
3M G5 User Guide
3M G5 Online Manual

Text of 3M G5 User Guide:

  • 3M G5, Installation 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual March 2014 – Revision 2.0 Page 27 of 74 Base Station to Base Station Wiring In any site with two base stations, the wiring between the two stations should be completed as follows and as shown in Figure 10: Important Note: Interconnected base stations must be the same revision level. • Interbase 1 terminals from base 1 connect to Interbase 1 terminals from base 2. • Interbase 2 terminals from base 1 connect to Interbase 2 terminals from base 2. • IN terminals connect to O

  • 3M G5, Installation March 2014 – Revision 2.0 Page 20 of 74 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual • Lift the cover upward and away. The display and keypad remain with the base, not with the cover. To replace the base station cover: • Verify there are no obstructions (tools, etc.) in the way of the cover being closed. • Align the top edge of the cover with the base. • Swing the bottom half of the cover down into place and gently push it against the base until it locks into pla

  • 3M G5, Index March 2014 – Revision 2.0 Page 72 of 74 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual Materials required ............................................ 10 MEN SKR ................................................. 21, 22 MIC ........................................................... 21, 22 Mic preamp gain .............................................. 53 Mode audio ............................................................ 44 order taking .....................

  • Configuration 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual March 2014 – Revision 2.0 Page 39 of 74 Change Basic Volume Settings Note: All volume settings should be adjusted during normal or peak business hours. Adjusting them during slow times will likely produce volume settings that are too low. Note: Inbound and outbound are always defined from

  • 3M G5, Installation March 2014 – Revision 2.0 Page 10 of 74 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual Installation Overview of Installation Installation involves the following main steps: 1. Design the installation 2. Install the battery charger and begin charging the batteries. 3. Install the order point speaker and microphone assemblies. 4. Install the base station(s). 5. Install the vehicle detector loop(s). 6. Install accessory boards in the base station(s). Required Materials (Not Supplied) • Standard or surface-mount condui

  • 3M G5, Installation March 2014 – Revision 2.0 Page 32 of 74 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual Figure 14 • Adjust the sensitivity of vehicle detection by manipulating the top two dip switches. • Enable or disable a two second detection delay by manipulating the third switch • Choose presence or pulse detection by manipulating the fourth switch. Figure 15 Vehicle Detector LED There are two small LEDs on the vehicle detector that can be in one of three states w

  • 3M G5, Installation March 2014 – Revision 2.0 Page 34 of 74 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual Power Up After installation is complete, you can power up the system by plugging in the base station transformer. Run Mode Menu When the system is powered up and functioning normally, the Run mode menu appears on the display. Figure 17 shows the Run mode menu. Figure 17 Navigating in the Base Station in Run Mode To navigate the base station in Run mode you only need to use Enter, Mode, and

  • Configuration 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual March 2014 – Revision 2.0 Page 51 of 74 Change Site Information Site information is useful for warranty registration and to support service calls. This information is most useful when the system has an internet connection. Tech Services can use it to identify and contact the s

  • Table of Contents March 2014 – Revision 2.0 Page 4 of 74 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual Appendix: Dual Lane Installation Instructions ..................................................................... 65 Recommended Procedure ..................................................................................................... 65 Appendix

  • 3M G5, Installation 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual March 2014 – Revision 2.0 Page 21 of 74 Figure 6 • Attach the base station to the wall using screws and possibly wall anchors. Note: Steps 3 and 7 assume that all of the communication cabling has been prepared and is available at the base station. If not, see “Base Station to Component Wiring,” page 24. • Follow local best practices and any applicable regulations to route the cables into the base station cabinet’s top, sides,

  • 3M G5, Installation March 2014 – Revision 2.0 Page 28 of 74 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual Figure 11 Notes: The cable coloring is valid for the D15 standard cable. For other cable types use the terminal definitions on page 21 as a guide. Auxiliary Detector Relays You can use the base station’s vehicle detection circuits to operate an auxiliary relay for a number of convenient uses (typically an external greeter or timer module, but could also be used to operate a vehicle approach chime or other device that is independent of the intercom system). Virtually any device that can be activated by opening or closing a switch can be linked to

  • 3M G5, Troubleshooting 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual March 2014 – Revision 2.0 Page 57 of 74 Red + 4sec blank + Red + 4sec blank…….. The Base Station you are trying to register your headset to, has more than 20 headsets registered already Follow the steps below to remove any registered headsets that are not in use any more. 1. Log into the Base Station 2. Press the Mode key till you see the System Menu 3. Select 04 Registration 4. Select 02 Remove Headsets. 5. Scroll to the number of the headset you want to un-register. 6. Press Enter. Blue (at Mic Boom tip) Solid blue, when holding the Vol

  • 3M G5, Overview 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual March 2014 – Revision 2.0 Page 7 of 74 The use of accessories not approved by 3M Company, including but not limited to batteries, antennas, wall adapters, chargers, ear pads and foam tips and convertible covers, may cause your headset to malfunction or in the case of unapproved electrical accessories may cause the devise to exceed RF energy exposure guidelines. FCC Note: This equipment has been tested and found to comply with the limi

  • 3M G5, Appendix: Dual Lane Installation Instructions March 2014 – Revision 2.0 Page 66 of 74 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual  PreAmp gain (page 54)  Outbound volume (page 39)  Inbound volume (page 34) • Thoroughly test the lane #2 intercom system. • Complete the configuration for both base stations (page 35).

  • 3M G5, Configuration March 2014 – Revision 2.0 Page 38 of 74 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual • Peer-to-Peer – a direct connection between the base station and the PC using a crossover cable • Private network – a connection between the base station and a router, switch or hub using an Ethernet cable. The PC is somewhere on the same network. • Enter the configuration mode, see page 35. • Select 16 Network Setup. • Change the values for IP address, subnet mask, default gateway, E-mail server, and Your E-Mail Address Suffix according to the table be

  • Troubleshooting March 2014 – Revision 2.0 Page 56 of 74 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual G5 Headset Indicator Light Modes Indicator Mode Description Off (no light) Indicates power is off. Headset is in sleep / hibernate mode. Picking up (or moving) the headset awakens it and the headset will begin to

  • 3M G5, Installation March 2014 – Revision 2.0 Page 14 of 74 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual 3M TM Drive-Thru Headset Charging Station, G5: Headset Charging Station, G5 uses the same power adapter as the basestation. Perform the following steps to install and use the Headset Charging Station, G5 • Select a placement location, either  A flat, dry surface such as a desktop or shelf.  An easy-to-reach wall location if you have the optional wall-mount bracket. • The po

  • 3M G5, Appendix: Dual Lane Installation Instructions 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual March 2014 – Revision 2.0 Page 65 of 74 Appendix: Dual Lane Installation Instructions This section provides a procedure for installing and configuring any system where there are two base stations (tandem, side-by-side, or dual drive thru). It is meant to be a time-saving reference that can be performed on existing drive- thrus that may be in-service during the installation. Important Note: Interconnecte

  • 3M G5, Appendix: Best Practices March 2014 – Revision 2.0 Page 62 of 74 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual Appendix: Best Practices This appendix provides best practices to help ensure successful configuration and operation of the 3M™ Wireless Communication System Model XT-1. PreAmp Setting Set the PreAmp gain setting according to the type of wiring you are using: • If you are using the provided 3M Microphone and the 20 AWG cable, set the PreAmp gain setting to 8. • If a 22 AWG cable is used, set the PreAmp gain setting to 9. Volume Control Here are s

  • Troubleshooting 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual March 2014 –Revision 2.0 Page 55 of 74 Troubleshooting Headset Indicator Lights The following table describes the operating modes of the headsets according to the indicator lights. Use it as a troubleshooting reference. XT-1Headset Indicator Light Modes Indicator Mode Description Off (n

  • 3M G5, Configuration March 2014 – Revision 2.0 Page 36 of 74 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual Interpreting Display Information Depending upon what you are doing, or what you can do, text on the display screen is handled according to the following conventions: Static or Informational Static, informational, or non- editable text has no markings on it. <Editable, not selected> Editable items that are not currently-selected appear inside of outwardly-pointing pointers. >Editable, Selected< Editable items that are curre

  • 3M G5, Configuration 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual March 2014 – Revision 2.0 Page 49 of 74 Haptics “Vibration” Alerts and Blue LED Alerts on Headsets These options allow you to enable the G5 headset to - Gently vibrate and/or -Flash a Blue LED (at the tip of the mic boom) when a vehicle is detected at the Order Point These options are, by default, set to YES. This option only applies to G5 headsets. If you currently have no G5 headsets and only XT-1 headsets, then enabling or disabling this option will not affect the normal functioning of the XT-1 headset. Im

  • 3M G5, Configuration 3M™ Drive-Thru Systems Model G5 and Model XT-1 Installation Manual March 2014 – Revision 2.0 Page 37 of 74 Mode (Exit) button In run mode, you must press and hold Mode while entering your passcode to enter user or installation service. In user and installation service modes, use the Mode button to exit from a current field that you are editing without saving any changes or to go upward (backward) in the configuration menus. Enter (Select) buttons (both buttons perform the exact same functions) Use the Enter button to execute the current

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 NewAir AWC-270E Owner's manual newair/awc-270e-4SK.pdf 14 Dec 2023 8
2 Yamaha Audiogram 6 Software manual yamaha/audiogram-6-9QU.pdf 28 Dec 2023 44 1.55 Mb
3 Audiovox CDM8930 Operation & user’s manual audiovox/cdm8930-C7R.pdf 14 Dec 2022 84
4 Xexun Tk 102-2 Operation & user’s manual xexun/tk-102-2-SYB.pdf 27 Nov 2023 16
5 Frigidaire Gas Oven Use & care manual frigidaire/gas-oven-L4R.pdf 21 Aug 2022 20 0.55 Mb
6 Sony VPL VPL-HW15 Specifications sony/vpl-vpl-hw15-16M.pdf 01 Jan 2023 2 0.44 Mb

Similar Resources:

  • Plantronics

    Savi W740

    (5 pages)
    Savi® W740 Wireless Headset System Quick Start GuideGuide de démarrage rapideGuía de inicio rápido Guia de Início Rápido1Savi WH500 Headset1 Volume Button (Press in to mute/unmute)2 Call Control Button3 Indicator Light 4 Microphone5 Headband6 Battery7 Eartips8 Earloops9 Charge Cradle89764235Savi WO2 Base1 PC Talk Button and Indicator Light 2 Mobile P …
  • Sony

    MDR-XB600

    (2 pages)
    MDR-XB600Stereo HeadphonesOperating InstructionsMode d’emploiBedienungsanleitungManual de instruccionesIstruzioni per l’usoGebruiksaanwijzingManual de Instruções Instrukcja obsługiHasználati útmutató4-430-799-21(1)English Stereo headphonesFeaturesNewly developed 40 mm driver unit reproduces natural powerful bass.Newly developed Advanced Direct Vibe …
  • RCA

    WHR120

    (8 pages)
    Thank you for choosing RCA Wireless Headphones. You have selecteda fine product designed to provide years of performance. Beforeattempting to use your Wireless Headphones, please remove all partsfrom the box and read the installation and use instructions carefully. WHR120 STEREOINFRARED HEADPHONELimited 1 Year Warranty WHR120wirelessHEADPHONESWITH FLAT TRANS …
  • Motorola

    V66I

    (192 pages)
    Welcome - 1WelcomeWelcome to the world of Motorola digital wireless communications! We are pleased that you have chosen the Motorola V66i wireless phone.Earpiece Headset JackInsert headset accessory for hands-free use.Status LightSee incoming call and service status.Volume KeysAdjust earpiece and ringer volume.Smart KeySelect menu items, send and end calls.V …
  • JBL

    Reflect Flow

    (2 pages)
    SELECT YOUR SIZE ATTACH ear tips and ENHANCERSMix and match for a perfect fit and audio performancehow to wearFirst time usepoweron &connectPairingPOWER OFFBUTTON COMMANDTECHSPECStep 1Step 3Step 2RAutomatically entering pairing mode Choose "JBL REFLECT FLOW" to connectONSettings BluetoothBluetoothDEVICESJBL REFLECT FLOWNow DiscoverableConnected …
  • Logitech

    Ultimate Ears 200

    (2 pages)
    www.logitech.com© 2011 Logitech. All rights reserved. Logitech, the Logitech logo, and other Logitech marks are owned by Logitech and may be registered. All other trademarks are the property of their respective owners. Logitech assumes no responsibility for any errors that may appear in this manual. Information contained herein is subject to change without …

Comments, Questions and Opinions: