Manualios.com

FALCOM SAMBA3G-E Operation & User’s Manual

FALCOM SAMBA3G-E Manual Online:

3.6, 2104 votes
FALCOM SAMBA3G-E User Manual
FALCOM SAMBA3G-E User Guide
FALCOM SAMBA3G-E Online Manual

Text of FALCOM SAMBA3G-E User Guide:

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 5.4 SIM-Card Reader The SIM interface controls 3 and 1.8V SIM cards. This interface is fully compliant with GSM 11.11 recommendations concerning SIM functions. Figure 6: SIM Card interface This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 18

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 1.3 Used abbreviations Abbreviation Description ETSI European Telecommunications Standards Institute GSM Global System for Mobile communications IMEI International Mobile station Equipment Identity ME Mobile Equipment EDGE Enhanced Data rates for GSM Evolution GPRS General Packet Radio Service GMSK Gaussian Minimum Shift Keying PLMN Public Land Mobile Network PIN Personal Identification Number PUK Personal Unblocking Key RP Receive Protocol SIM Subscriber Identity Module SMS Short Message Service SMS/PP Short Message Service/Point-to-Point TA Terminal Adapter TE Terminal Equipment TP Transmit Protocol MS Mobile Station USB Universal

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 D) On the next screen, select the "Install from a list or specific location(Advanced)" option and then click Next. Figure 9: Searching modem USB driver E) The "Please choose your search and installation options" dialog will appear. Select the "Include this location in the search" option under "Search for the best driver in these locations", and then use the Browse button to navigate to the unzipped USB Modem folder (e.g. "D:\Samba3G_USB_Driver"). Figure 10: Browsing to modem USB driver This confidential document is a proper

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 5 INTERFACES IN OVERVIEW The table below lists all interfaces available on the SAMBA3G-E modem: Interface specifications USB USB A-type plug connector is used to connect the modem to a a USB host. This interface USB 2.0 supports a Full Speed rate of 12 MBits/s. LED Used to show the status of the modem. SIM SIM card reader for small SIM cards (3/1.8V). AUDIO 4pin jack for headset Table 4: Modem interfaces Figure 1: View of SAMBA3G-E interfaces. 5.1 4pin audio jack The SAMBA3G-E modem has a 4pin au

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 7 APPENDIX 7.1 Accessory headset for SAMBA3G-E The retractable Headset with a 2.5mm plug (see also figure below) included in the SAMBA3G-E-SET fully compatible with SAMBA3G-E phone is designed to do two things at once, if those two things are driving and talking on the cell phone. The retractable Headset is lightweight, super-easy to use, comfortable, and has great incoming and outgoing sound quality. Retractable quality earpiece and microphone pulling out to desired length independently. The retractable cord length is 78 mm. The headset length is

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 F) Wizard copies the driver files automatically. Figure 11: Installing modem USB driver During the installation, if popup window appears, just click the “Continue Anyway”. Figure 12: Browsing to modem USB driver This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 22

  • SAMBA3G-E USER’S GUIDE VERSION 1.0.1 2.11 Non-ionizing radiation The SAMBA3G-E comes with an internal antenna. Therefore, care should be taken to install the modem in such a position that no part of the human body will normally rest within 20 cm of any part of the modem. It is also recommended to use the modem not close to medical devices as for example hearing aids and pacema

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 Figure 4: USB Y-Cable (not included, available upon request) 5.3 Status LED The actual state of the SAMBA3G-E is displayed by one LED (its functionality is given in table below). Figure 5: Status LED It is a debug aid that shows information on the network service availability. Name LED mode Function Status LED Off Modem is off Fast blinking (period 1s, Ton 0,5s) Net search / Not registered / turning off Slow blinking (period 3s, Ton 0,3s) Registered: full service Perma

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 2.5 Vehicle electronic equipment Check your vehicle manufacturer’s representative to determine if any on board electronic equipment is adequately shielded from RF energy. 2.6 Medical electronic equipment Consult the manufacturer of any personal medical devices (such as pacemakers, hearing aids, etc.) to determine if they are adequately shielded from external RF energy. Turn your SAMBA3G-E device OFF in health care facilities when any regulations posted in the area instruct you to do so. Hospitals or health care faciliti

  • SAMBA3G-E USER’S GUIDE VERSION 1.0.1 G) When the "Completing the Found New Hardware Wizard" screen appears, click Finish. Figure 13: Completing modem USB driver H) After the installation of SAMBA3G-E USB Modem, Hardware Wizard will appear 2 times more to install Telit Auxiliary Port and Telit Diagnostics Interface. You are able to install these two driv

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 2 SECURITY IMPORTANT FOR THE EFFICIENT AND SAFE OPERATION OF YOUR GSM-MODEM, READ THIS INFORMATION BEFORE USE! Your cellular engine SAMBA3G-E is one of the most exciting and innovative electronic products ever developed. With it you can stay in contact with your office, your home, emergency services and others, wherever service is provided. This chapter contains important information for the safe and reliable use of the SAMBA3G-E modem. Please read this chapter carefully before starting to use the cellular engine SAMBA3G. 2.1 Ge

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 Figure 16: HyperTerminal screen. To enter the PIN code of the used SIM card type on the terminal screen: AT+CPIN=pin<enter> // pin = PIN code of your SIM card Modem responds: OK The SAMBA3G-E will go into the search mode and the Status LED will operate as described in Table 6. For more information about AT commands, please refer to the manual "Telit_AT_Commands_Reference_Guide_UC864.pdf" available in the FALCOM website. This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 25

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 b) How to remove the SIM card:  To remove the SIM card, just press the inserted SIM card by using your finger nail or a pointed object. The SIM card will jump out when you release it. Finally, take it out. Important: Do not insert or remove the SIM card when the device is under power. Keep all miniature SIM cards out small children’s reach. The SIM card and its contacts can be damaged by scratches or bending, so be careful when handling, inserting or removing the SIM card. 2 - How to use SAMBA3G

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 3 SAFETY STANDARDS Your GSM mobile complies with all applicable RF safety standards. The GSM mobile meets the safety standards for RF receivers and the standards and recommendations for the protection of public exposure to RF electromagnetic energy established by government bodies and professional organizations, such as directives of the European Community, Directorate General V in matters of radio frequency electromagnetic energy. This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 12

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 3 - Plug a headset to the audio jack on modem: If you are using the included headset (refer to the chapter Appendix for more details), then plug the 2.5 mm plug of the headset into the 2.5 mm jack of the modem (see figure below). Figure 15: Connect the headset to the modem 4 - Setup HyperTerminal program To communicate with the SAMBA3G-E modem, start the HyperTerminal program or another terminal program, and then use the AT commands avail

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 Authentication Protocol) commonly used for PPP connections. ➢ Supports of Packet Switched Broadcast Control Channel (PBCCH) allows you to benefit from enhanced GPRS performance when offered by the network operators. CSD ⇒ ➢ Downlink/Uplink up to 14.4 kbps.  Additional features: ➢ Voice and SMS ➢ Embedded TCP/IP stack with IP and UDP protocols, access via AT commands ➢ Standard and extended AT command set ➢ Minimal power consumption ➢ Firmware upgradeable via

  • SAMBA3G-E USER’S GUIDE VERSION 1.0.1 1.2 Scope of delivery Check the contents of the ordering item. The following listed parts of chosen item should be included. In case of damaged or missing any part, please contact your dealer immediately. SAMBA3G-E SAMBA-USB-KIT KA18 (Y-Cable) KA19 Ordering D

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 4 TECHNICAL DATA 4.1 General specifications of SAMBA3G  Power supply: ➢ +5 VDC through USB port, compliant with USB 2.0 specification.  Extended Temperature range: ➢ Operational: -30 °C to +80 °C ➢ Storage temperature: -40 °C to +90 °C  Physical characteristics: ➢ Size: 88.7mm x 37.6mm x 14.1mm (L x B x H) ➢ Weight: 35 g  Frequency bands: ➢ GSM 900, DCS 1800 MHz ➢ WCDMA 2100 MHz ➢ Compliant to GSM Phase 2/2+  Transmit

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 Version history: This table provides a summary of the document revisions. Version Author Changes Modified 1.0.1 F. Beqiri - The SAMBA 3G modem is designed for industrial M2M applications. - Updated chapter "Scope of delivery" - Replaced Fig.8a, Fig.8b and Fig.8c by Fig. 8. - Added CAUTION. 11/12/2009 1.0.0 F. Beqiri - Initial version 24/10/2008 This confidential document is a property of FALCOM GmbH and may not be copied or circulated without previous permission. Page 3

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 Table of contents 1 INTRODUCTION.......................................................................5 1.1 GENERAL..........................................................................................................................5 1.2 SCOPE OF DELIVERY............................................................................................................6 1.3 USED ABBREVIATIONS...........................................................................................................7 1.4 RELATED DOCUMENTS................................................

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 6 SYSTEM REQUIREMENTS Check your hardware and software and see if they satisfy the requirements below. If you are not sure, please consult your vendor or operator. 6.1 Hardware & software requirements Hardware & software requirements  A valid SIM card (with UMTS enabled).  2 x Free compatible USB port  Approximately 6 Mb of free hard disk space.  Pentium 90 or higher.  Operating system: Windows® XP  CD-ROM drive. For data applications.  Browser and em

  • SAMBA3G-E USER’S GUIDE VERSION 1.0.1 Cautions Information furnished herein by FALCOM is believed to be accurate and reliable. However, no responsibility is assumed for its use. Please, read carefully the safety precautions. If you have any technical questions regarding this document or the product described in it, please

  • FALCOM SAMBA3G-E, SAMBA3G-E USER’S GUIDE VERSION 1.0.1 1 INTRODUCTION This manual is focussed on the GSM/GPRS/EDGE/UMTS data solutions of the enhanced performance SAMBA3G-E USB modem from FALCOM Wireless Communications GmbH. 1.1 General The SAMBA3G-E portable USB modem is a 3.5G wireless data modem, compact, light- weight that features a single-band 2100MHz UMTS/HSDPA radio for data connectivity. The SAMBA3G-E is fully backward compatible to existing EDGE and GSM/GPRS networks and maintains the same form-factor of the well-known SAMBA55-56/SAMBA75 modems. The major benefit over earlier SAMBA55-56/SAMBA75 is that it supports HSDPA/UMT

Related Products and Documents (Modem):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Xclaim Xo-1 Quick setup manual xclaim/xo-1-9E7.pdf 28 Aug 2023 4
2 Transition Networks CPSMC0100-200 Operation & user’s manual transition-networks/cpsmc0100-200-HSR.pdf 13 Aug 2022 5 0.32 Mb
3 LaCie big disk extreme + Quick install manual lacie/big-disk-extreme-362.pdf 22 Dec 2023 24
4 Buffalo WZR-G108 Brochure & specs buffalo/wzr-g108-K8T.pdf 29 Nov 2022 2 0.22 Mb
5 Olympus E-5 Instruction manual olympus/e-5-E2X.pdf 12 Jul 2022 172
6 Philips SWV2547T Specifications philips/swv2547t-7N9.pdf 18 May 2023 2

Similar Resources:

  • AT&T

    RM 5400

    (10 pages)
    Equipment information and assembly guide for your AT&T Service© 2013 AT&T Intellectual Property. All rights reserved. AT&T, Globe logo and other marks are trademarks of AT&T Intellectual Property. Please ensure that you have set-up the equipment before the date scheduled with your AT&T Order Manager for Test and Turn Up of your site …
  • NETGEAR

    CBVG834G

    (82 pages)
    202-10338-01 v1.0February 2008NETGEAR, Inc.4500 Great America Parkway Santa Clara, CA 95054 USAWireless Cable Voice Gateway Model CBVG834G Adminstrators User Manual …
  • Cisco

    DPC3000

    (36 pages)
    Cisco Model DPC3000 and EPC3000 DOCSIS 3.0 Cable Modem User Guide In This Document  IMPORTANT SAFETY INSTRUCTIONS ...............................................................2  What's in the Carton? ...............................................................................................11  Front Panel Description ............. …
  • BroadMax Technology

    HSA300A-2

    (2 pages)
    Ethernet PortLINE10BASE-T6V DCThis guide details how to connect your BroadMax HSA300A-2 UHPmodem. For complete instructions and support information, please seethe EarthLink DSL Internet Quickstartguide provided in your kit.3322BroadMax HSA300A-2 ModemReference GuideConnecting Your BroadMax HSA300A-2 Modem: …
  • Wetelecom

    WM-D300

    (30 pages)
    USB modem Wetelecom WM-D300 Installation and connection manualMTS Connect 3G� …
  • ICP DAS USA

    GTM-201-RS232

    (8 pages)
    GTM-201-RS232 Quick Start Industrial Quad-band GPRS/GSM Modem GTM-201-RS232 Quick Start Manual Package Checklist The package includes the following items: z One GTM-201-RS232 hardware module z One Quick Start Manual (this manual) z One companion CD z One RS-232 9-pin Male-Female D-sub cable (CA-0915) z One GPRS ante …

Comments, Questions and Opinions: