Manualios.com

Cal Amp vanguard Operation & User’s Manual

Cal Amp vanguard Manual Online:

4.65, 2286 votes
Cal Amp vanguard User Manual
Cal Amp vanguard User Guide
Cal Amp vanguard Online Manual

Text of Cal Amp vanguard User Guide:

  • Cal Amp vanguard, 62  Unit ID The Unit Name to be included in the NMEA message payload.  Source Identification The Unit's IP address that will be included in the NMEA message payload Triggers – Device  Cell Temperature and thresholds Enable or disable NMEA alarm and notification when temperature goes out of range. Triggers – Analog Input  Analog Input and thresholds (1 or 2) Enable or disable NMEA alarm and notification when an analog input goes out of range. Triggers – Digital Input  Digital Input 1, Digital

  • Cal Amp vanguard, 44 Figure 28: Vanguard Router – Static Routes Static Routes  Route Name Sets the alphanumeric identifier of the static route in the Static Route Table  Destination IP Address Sets the IP address of the destination network  IP Subnet Mask Sets the subnet mask of the destination network  Gateway Sets ppp (this router's wireless internet connection), pptp (VPN), GRE Tunnel, or the local network IP address for the gateway to the destination network  Gateway IP Address This is only used if local IP addr wa

  • Cal Amp vanguard, 39  DHCP end range DHCP server ending IP address. The maximum usable number is 253  DHCP Lease Time Sets the duration, in seconds, the connected device is allowed to keep the assigned IP address. In many cases it is possible for the device to receive the same IP address after the lease time expires. Remote Administration  Web Server Port Enter the port number to be used by the web server  Remote Configure Selecting Enable will allow remote access to the modem’s configuration screens through the cellular network connection. Selecting Disable will shut off the ability to remotely access the mod

  • Cal Amp vanguard, 34  Destination Address User may enter an accessible IP address or URL that will respond to a ping command.  Secondary Address User may enter an accessible IP address or URL that will respond to a ping command. This address will be used if the entered number of consecutive ping failures using the first address is reached.  Periodic Ping Timer User may enter an interval in increments of 10 seconds. The modem will ping the destination at that interval. Enter 0 to disable this feature.  Fail Count The modem will reset if the number of consecutive ping failures is equal to or greater than this entry and the secondary address is being used. Otherwise th

  • Cal Amp vanguard, 54 New Client: If a different client attempts to connect, it will be successful and the current client will be forcibly disconnected, without any warning. Otherwise, the current client remains connected indefinitely. Timeout: A new client will be accepted only after a specified timeout. The duration of the timeout is specified by the Inactivity timeout, or the Hard timeout, or a combination of both. The default value is New Client.  Server Inactivity Timeout Time after which the current connection with Client will be terminated without warning. This time star

  • Cal Amp vanguard, 25 3.3 PROVISIONING (CDMA MODELS ONLY) When a CDMA modem is powered up for the first time, most of the provisioning information is blank or has information that needs to be changed. The device is usually shipped with the radio ready to be provisioned on a cellular carrier’s network. Features called Over-The-Air Service Provisioning (OTASP) and Internet Over-The-Air (IOTA) are supported, which allow the cellular providers to program the modem with specific information to activate the account. From the main navigation panel, select provisioning to access the primary provision screen and for access to the advanced settings tab. 3.3.1 VERIZON WIRELESS PROVISIONING INFORMA

  • Cal Amp vanguard, 5 3.10.1 Status ............................................................................................................................................................... 58 3.10.2 Settings ............................................................................................................................................................ 60 3.10.3 Labels ............................................................................................................................................................... 61 3.11 Firmware Update ......................................................

  • 60 Figure 36: Vanguard I/O Settings – Status Device Input Status  Main Voltage Displays current voltage applied to the unit, in Volts  Modem Temperature Displays temperature of the Wireless Modem, in Celsius Analog Input Status  Analog Input 1, Analog Input 2 Displays voltage of the specified analog input, in Volts. Digital Inp

  • Cal Amp vanguard, 13 antenna, with an average gain >-5dBi, if using the GPS functionality. If both RX diversity and GPS are required, install a Cellular/GPS combo antenna. This device is configured with default settings and is ready to be configured via HTML. Some configurations may be set using AT commands. Refer to Section XX for AT Commands using the Serial Port. 1.8 RS-232 SERIAL PORT INTE GRATION PARAMETERS Table 5 provides the serial cable design information to integrate the Vanguard modem into your system. Table 6 gives the default RS-232 communication parameters. Table 5 – Standard RS-232 DE-9 Pin out Pin Name Direction Description 1 CD ←

  • Cal Amp vanguard, 53  DCD The DCD parameter determines how the modem controls the state of the Carrier Detect circuit and the amber DCD LED on the front panel. The default value is Connect On. ― Always On: DCD is always on. ― Connect On: DCD is on when connected to a remote host. ― Always Off: DCD is always off.  RI The RI parameter determines how the modem controls the state of the Ring Indicator circuit. The default value is Always Off. ― Always On: RI is always on. ― Connect On: RI tracks incoming ring pulse. ― Always Off: RI is always off.

  • 9 Table 2 - Vanguard Accessories Vanguard Accessories ACC-ANTN-RBD 4” Rubber Duck Antenna ACC-ANTN-MAG 3” Mag Mount Antenna ACC-PWSP-ML2 110 VAC Input Power ACC-PWDC-MLX DC Power Cable ACC-CABL-SER DB-9 Serial Cable ACC-CABL-ETH 7’ Ethernet cable

  • Cal Amp vanguard, 42 Figure 27: Vanguard Router – Port Forwarding DMZ Support DMZ is a host on the internal network that has all ports exposed, except those ports forwarded otherwise.  DMZ Radio button selection to Enable/Disable; Select Enable to allow the modem to use DMZ routes using the address set in the Destination IP Address. Select Disable to shut down the DMZ functionality.  Friendly IP Address Optionally restricts DMZ access to only the specified IP address. If set to "0.0.0.0

  • Cal Amp vanguard, 52  Baud Rate Sets the baud rate of the serial port. Settings may range from 300 to 115,200 bits per second. The default baud rate is 115,200 bps.  Inter Character Timeout Sets the Inter Character Timeout from 1 to 65,535 ms.  DTR Defines the Data Terminal Ready behavior. Refer to Table XX for DTR descriptions. Table 7 – DTR Descriptions AT&D0 Ignore DTR. AT&D1 If in the Online Data State, upon an on-to-off transition of DTR, the modem enters Online Command State and issues an OK result code; the call remains connected. Otherwise, i

  • Cal Amp vanguard, 26  If the auto-provisioning fails, and OMA-DM manual provisioning fails, and your outside the Sprint network, follow the manual-entry activation steps below. Manual-Entry Activation  If provisioning must occur in a roaming area, make sure to have a medium to strong signal strength because manual-entry activation will be required.  Select Provisioning from the side menu bar.  Input the MDN/MTN and MSID/IMSI (MIN) given by your provider.  Put in the unlock code given by your provider.  Click the Write MDN/MSID button. Figure 19: Vanguard CDMA Provisioning Window Current Status  ESN

  • Cal Amp vanguard, 50 Figure 31: Vanguard VPN – GRE GRE Tunnel Configuration  Local IP Address The local IP address associated with the tunnel  Remote IP Address The remote IP address associated with the tunnel  Tunnel IP Address The IP address assigned to the tunnel interface. 3.8 SERIAL From the main navigation pane, select Serial for access to both external and internal serial port configuration screens. 3.8.1 EXTERNAL SERIAL The External Serial screen is used to configure the RS-232 Serial Port parameters and Packet Assembler and Disassembler (PAD) functionality. The PAD feature forwards requests that come in on a specific

  • Cal Amp vanguard, 57 Figure 34: Vanguard Diagnosics – SNMP SNMP Configuration  SNMP Selecting Enable will allow the SNMP functionality. Selecting Disable will shut off SNMP functionality.  Version With SNMP Enabled, select the corresponding version that matches the SNMP Manager. SNMP v2c  Read-only Community Name The community string used for accessing the read-only Management Information Bases (MIBs)  Read-write Community Name The community string used for accessing all Management Information Bases (MIBs) including writable objects

  • Cal Amp vanguard, 28 Click the Write MDN/MSID button when the required information has been entered. Enable/Disable OMA-DM Activation This section will only be displayed for units which are capable of automatic (OMA-DM) provisioning. You may choose to enable or disable the automatic provisioning and save your desired setting. If enabled, and the unit is not provisioned (activated), each time at power-on (only) the unit will attempt an auto-activation. This capability is dependent on whether or not it is offered by your cellular carrier.  Auto-Activation Choose Enabl

  • Cal Amp vanguard, 41 Figure 26: Vanguard LAN Settings – MAC Filtering MAC Filtering  MAC Filtering Radio button selection to Enable/Disable MAC filtering  Allowed MAC Address Enter the MAC address for a device to be allowed on the network.  Comment Here a name can be inserted describing the device using the allowed MAC address.  Clear Press to remove the MAC address from the list of allowed addresses. Press SAVE/CANCEL to implement or cancel changes. 3.6 ROUTER Select Router from the left navigation pane for user access to Port Forwarding and Static Routing tabs. 3.6.1 PORT FORWARDING Port Forwarding is a t

  • Cal Amp vanguard, 24 Figure 16 SIM Settings for PIN Required At this point the user has 3 attempts to enter the correct PIN. If the correct PIN is not entered after 3 attempts, an unlock code or PIN Unblocking Key (PUK) from the service provider will be required before the SIM card is usable again. Figure 17 shows the SIM settings after an incorrect PIN has been entered. Figure 17 SIM PIN Rejected Figure 18 shows the SIM page requiring the unlock code to be entered. At this point the user has 10 attempts to enter the correct unlock code or

  • Cal Amp vanguard, 35 The number of corrupted TCP and UDP packets received by the modem that were meant to be transmitted on the cell network.  Tx Packets Dropped The number of TCP and UDP packets received by the modem for transmit to the cell network that were not accepted. This may occur due to memory or throughput problems. Press Clear to reset the totals to 0. These totals are NOT cleared by a modem reboot. 3.4.3 DYNAMIC DNS Select Cell Connections from the left navigation pane. Select the Dynamic DNS tab to open the Dynamic DNS configuration page. Dynamic DNS is a system which allows the domain name data of a computer with a varying (dynamic) IP addr

  • Cal Amp vanguard, 27 The Electronic Serial Number is only applicable for the CDMA product line, carrier specific (Alltel, Verizon, Sprint, etc). This number is used to set up the user account with the cellular provider.  MDN/MTN The actual phone number of the device as supplied by the carrier. When the unit is successfully provisioned, the phone number for the user account will be displayed.  MIN/IMSI This number is used by the Mobile Telephone Network and will be different if ported from another carrier (not used by end user of device).  PRL Preferred

  • Cal Amp vanguard, 14 2 GETTING STARTED 2.1 PACKAGE CONTENTS  Vanguard Modem  Power Cable  Information Card 2.2 DEVICE CONNECTIONS 1. (GSM Users) Insert the SIM card into the SIM/SVC slot as shown. 2. Connect an antenna to the ANT connector on the front panel of the Vanguard modem. 3. Connect an Ethernet cable into the LAN 1 port and plug the other end into the network port of your PC. 4. Connect the Power Adapter to the modem PWR port and plug into a proper AC power socket. 2.3 LAN CONFIGURATION This device is configured via the Internet which automatically allows your computer to obtain the proper IP address. For Windows XP

  • Cal Amp vanguard, 48  NAT Mode Determines how packets are addressed. Selecting Bypass will allow packets coming from Local Subnet addresses through the NAT firewall unchanged. This may be sufficient when traffic only travels from Local Subnet to Remote Subnet. (LAN Settings > Bind to Eth IP may need to be enabled to make sure that packets generated by Vanguard services appear to originate from a Local Subnet address.) NAT changes the source address to match the Status > PPP IP Address. NAT-Traversal enables the NAT-T protocol which can support

Related Products and Documents (Network Router):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Panasonic KX-TG5240M - GigaRange Supreme 5.8 GHz DSS Expandable Cordless Phone Operating instructions manual panasonic/kx-tg5240m-gigarange-supreme-5-8-ghz-dss-expandable-cordless-phone-N7Z.pdf 28 Jun 2022 104 5.17 Mb
2 GRASS VALLEY K2 DYNO Datasheet grass-valley/k2-dyno-37V.pdf 11 Dec 2023 8 2.69 Mb
3 Ryobi RY09055 Operator's manual ryobi/ry09055-C85.pdf 16 Feb 2023 42 4.91 Mb
4 Texas Instruments Stellaris LM3S9B96 Operation & user’s manual texas-instruments/stellaris-lm3s9b96-CWX.pdf 19 Aug 2022 81
5 Polar Electro S710 Operation & user’s manual polar-electro/s710-Y21.pdf 05 Jul 2023 59
6 Lightolier SC4WC232 Specification lightolier/sc4wc232-9FS.pdf 06 Aug 2023 2

Similar Resources:

  • Delta

    DX-3001H9-V

    (67 pages)
    www.deltaww.com2020-05-14DX-3001H9-V Industrial3G/WAN VPN Router User ManualIndustrial Automation HeadquartersDelta Electronics, Inc. Taoyuan Technology CenterNo.18, Xinglong Rd., Taoyuan City, Taoyuan County 33068, TaiwanTEL: 886-3-362-6301 / FAX: 886-3-371-6301AsiaDelta Electronics (Jiangsu) Ltd.Wujiang Plant 31688 Jiangxing East Road, Wujiang Economic Dev …
  • Cisco

    1417

    (8 pages)
    Quick Start GuideINSTALLING YOUR CISCO 1417 ROUTERUNPACK THE BOXINSTALL THE ROUTERVERIFY YOUR INSTALLATIONCisco 1407/1417HubPCPCInternetADSL connectionPCPCPCPCServerServer123 …
  • NetModule

    NB2800

    (2 pages)
    www.netmodule.com 8/7/2017 © NetModule AG | Errors reserved NB2800 Overview 1 LED Status indicator. - STAT blinking: The device is busy due to startup, software or configuration update. - STAT on: The device is ready. 2 USB USB 3.0 host port 3 SIM slots Slots for 4 Micro SIM cards (3FF). SIM cards can be inserted by sliding it into one …
  • Draper

    Router

    (12 pages)
    ROUTER■ STOCK No.57853 (230V) ■ PART No.R1900V65027 (110V)03/2001• INSTRUCTIONS •IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURETHE SAFE AND EFFECTIVE USE OF THIS TOOL.GENERAL INFORMATIONThis manual has been compiled by Draper Tools and is an integrated part of the power tool equipment,which should be kept with the machine.This manual d …
  • Alcatel-Lucent

    7705 SAR

    (356 pages)
    Alcatel-Lucent 7705SERVICE AGGREGATION ROUTER OS | RELEASE 6.2.R1SYSTEM MANAGEMENT GUIDESYSTEM MANAGEMENT GUIDEAlcatel-Lucent – Proprietary & ConfidentialContains proprietary/trade secret information which is the property of Alcatel-Lucent. Not to be made available to, or copied or used by anyone who is not an employee of Alcatel-Lucent except when the …
  • Samsung

    SCH-LC11

    (46 pages)
    100031015THIS FILE MAY CONTAIN IMAGES OR ILLUSTRATIONS THAT ARE COPYRIGHT PROTECTED. CLIENT MUST OBTAIN PROPER LICENSING AND USAGE RIGHTS PRIOR TO REPRODUCTION. SUPPLIER IS RESPONSIBLE FOR CHECKING WORKING DRAWINGS BEFORE PLATES ARE MADE FOR ACCURACY IN MEASUREMENTS, PLATE TOLERANCE REQUIREMENTS, REGISTRATION AND CONSTRUCTION DETAILING. ANY …

Comments, Questions and Opinions: