CalAmp Sentry 4G-900 Operating Manual

Text of CalAmp Sentry 4G-900 User Guide:

• CalAmp Sentry 4G-900, Wireless – Access to all WiMAX parameters configuration and diagnostics options. Quick Start – Access to all parameters required for initial set up of the system, depending on the operation mode (Standalone / ASN-GW). 2.3.3 Modifying Parameters Modified parameters are updated on the Base Station under three conditions, depending on the parameter: • Some parameters do not require special operations - simply click Apply and they are updated on the Base Station. • Some parameters affect the service – these are marked by an exclamation mark (!). To update these parameters, click Stop Service and then Start Service (in the Quick Start panel). • Some par

• 2.2 Initial Setup the Base Station via Quick Start NOTE: The Quick Start menu is usually accessed for the first time via a local connection BEFORE the Base Station is mounted onto the pole. The Quick Start screen concentrates the IP address and other basic parameters required to set up the Base Station and to perform basic operations; these include Ba

• CalAmp Sentry 4G-900, © CalAmp Sentry 4G-900 Pico Base Station 52 Field Description Values: [0,113] Default: 0 TDD Split [%] Current / Configured DL frame resources [%]: Ratio (in percentage) between DL and UL. Values: [53,75] Default: 66 DL Major Groups Bitmap (0..63) Each bit 1-6 represents one Major or Minor group of DL resources (1-6 correspondingly). Note at least one major group shall be selected. Values: [0,63] Default: 63 UL Subchannels Bitmap UL Sub-channels Bitmap DCD Count Downlink Channel Descriptor Count. UCD

• CalAmp Sentry 4G-900, 3. Update the required parameters in the Pane table according to the following descriptions and click Apply. Field Description Index DIUC Index Table Index is for: 0 - IUC 0 1 - IUC 1 2 - IUC 2 : 12- IUC 12 Values: [0,11] Default: 0 Modulation and FEC code Values: 6.2.7 UL Modulation This pane provides a table with UL Coding and Modulation settings. To access the UL Modulation pane 1. Click the Wireless menu option and then the Radio and Frame sub-menu option. From the Radio and Frame sub-menus choose UL Modulation. The UL Coding and Modulation Settings pane is

• CalAmp Sentry 4G-900, 4.5.4 Managing Main Software Components This pane provides options for copying selected Main software files to a user defined URL or to the Base Station Secondary software directory. To access the Primary Bank (Main Version) pane 1. Click the Admin menu option and then the SW Upgrade sub-menu option. From the SW Upgrade sub-menus choose Primary Bank. The SW Primary Version Components pane is displayed. 2. Update the required parameters in the Pane table according to the following descriptions. Field Description Name SW Component Name (e.g. Base Station -GUI, etc.) Type Type of the SW component. Values: Package, Application, VxWorks, Blob, Scr

• 6.5 Diagnostics Information regarding the throughput values. 6.5.1 Aggregate Throughput This pane provides read only aggregated Throughput Values (i.e. Dropped Packets, CRC failures, etc.). To access the Aggregate Throughput pane 1. Click the Wireless menu option and then the Diagnostics sub-menu option. From the Diagnostics sub-menus choose Aggregate Throughput. The Aggregated Thro

• CalAmp Sentry 4G-900, © CalAmp Sentry 4G-900 Pico Base Station 49 Field Description Min / Max support Transmit Power [dBm] Min / Max support Transmit Power [dbm]. Values: Min and Max separated by comma. Example: 10,36 Number of RF Channels[2x2] Number of RF TX Channels 6.2.2 Radio Settings This pane provides Radio parameters settings. To access the Radio Settings pane 1. Click the Wireless menu option and then the Radio and Frame sub-menu option. From the Radio and Frame sub-menus choose Radio. T

• CalAmp Sentry 4G-900, 4.5.2 FTP Server Configuration Use this pane to define the location and access information of the FTP server in which software versions are stored. To define the FTP Server parameters 1. Click the Admin menu option and then the SW Upgrade sub-menu option. From the SW Upgrade sub-menus choose FTP Server. The FTP Server Properties pane is displayed. 2. Define the FTP server parameters described below and click Apply: • Server IP Address • Directory – directory in which files are located • User Name and Password – your FTP User Name and Password. © CalAmp Sentry 4G-900 Pic

• 4.5.1 Activating Software Versions ..................................................................................... 25 4.5.2 FTP Server Configuration .......................................................................................... 26 4.5.3 Downloading Software Versions ..........................................................................

• 2. The parameters displayed in the Pane are according to the following descriptions: Field Description Aggregated Dropped DL / UL Packets Total number of aggregated Dropped DL / UL Packets since last reset. Aggregated DL / UL Packets Total number of Aggregated DL / UL Packets since last reset. Aggregated DL / UL Bytes Total number of Aggregated DL / UL

• CalAmp Sentry 4G-900, © CalAmp Sentry 4G-900 Pico Base Station 39 Max Rate [Kbits/sec] Maximum rate for this SF. A value of ‘0’ provides unlimited rate. Max Latency [µsec] (UGS, RT, eRT) Relevant only for UGS, RT and eRT. A value of ‘0’ does not put a limit on latency. Maximum Latency (delay) for this SF. Set value according to the type of service (i.e. <100ms for Voice and Video applications. Unsolicited Grant [µsec] Interval (UGS, eRT) Relevant if the UGS – UGI - TBD A value of ‘0’ provides unlimited UGI. Tolerated Ji

• CalAmp Sentry 4G-900, The following operation buttons are available: • Apply – used to apply changes to selected classifier • Back – go back to the SF screen (to choose another SF). 3. Click the '+' sign to add a new row. 4. Update the required parameters in the Pane table according to the following descriptions and click apply to implement the changes for each row. NOTE: Once the classifier for the SF has been defined, the SF configuration is complete and the SF can be assigned to the desired SSs. The following table provides a descrip

• CalAmp Sentry 4G-900, 6.4 MAC The MAC configurations menus are displayed according to the Base Station operation mode: • Standalone mode – A single pane is available, providing the UCD/DCD time interval and the UCD/DCD number of notifications. • ASN-GW mode – three panes are available, describing the MAC settings, Neighbor Base Stations and DCD triggers. The following sections describe the ASN-GW mode MAC screens. 6.4.1 General Info – MAC Settings This pane provides general MAC settings such as MAC messages time intervals, formats, etc.

• The Web Manager window appears. The window consists of: • Dashboard showing the main readings – click on a reading to access the corresponding screen. • Main menu options – the relevant sub-menus are displayed in the left pane • The display area showing the currently selected sub-pane options. For a detailed explanation on navigating the Web Manager, refer

• CalAmp Sentry 4G-900, Resetting the connection of all registered SSs (in case the SF is applied to All Users): • Click the Quick Start menu option. • In the displayed Quick Start pane click the Stop Service button, and then click the Start Service button. 6. Repeat the above procedure to assign additional SFs to the SS as required. 5.4 Monitoring and Maintaining Registered SSs Connections This pane displays a table summarizing the registered SS units basic operation information, and provides basic maintenance operation buttons. To access the SS Lists pane 1. Click the Subscribers menu option and then the Subscriber Management sub-menu option. Ch

• CalAmp Sentry 4G-900, © CalAmp Sentry 4G-900 Pico Base Station 32 4.5.6.2 Running the New Software Version Run the Secondary software version: • Under SW Upgrade, choose SW Properties. • Click Run Secondary. The Base Station will reset and the Secondary files will be loaded. This will take about 2 minutes.

• CalAmp Sentry 4G-900, 3. Update the required parameters in the Pane table according to the following descriptions and click Apply. Field Description Index UIUC Index Table Index is: 0- IUC 0 (FFB) 1- IUC 1 2- IUC 2 : 10- IUC 10 Values: [0,11] Default: 0 Modulation and FEC code Values: 6.2.8 DL Zones This pane provides DL Zone settings. To access the DL Zones pane 1. Click the Wireless menu option and then the Radio and Frame sub-menu option. From the Radio and Frame sub-menus choose DL Zones. The DL Zone Settings pane is displayed. 2. To Add a row to the table click t

• CalAmp Sentry 4G-900, 4.2 Base Station Identification Information This information includes the site ID, Base Station location and antenna details. To define Base Station identification information 1. Click the Admin menu option, the General sub-menu option and then choose Installation Specific. The Installation Specifics 2. Define the Site ID as defined by the Network Operator and click Apply. Several Base Station may have the same site ID. Values: [0,1000000] 3. Enter more descriptions on the location of the Base Station: • Choose Installation Description (from the Admin menu, General sub-menus). The Installation Description pane appears.

• CalAmp Sentry 4G-900, 3.3.2 MAC Addresses Table This is a read-only pane, and displays the MAC addresses learned by the Base Station, that are used by the L2 switching mechanism. To view the Switching MAC Addresses Table 1. Click the Backbone menu option and choose Switching and then MAC Addresses Table from the sub-menus. The MAC Addresses Table pane is displayed. 2. The displayed information details are provided in the following table: Field Description Index Unique identifier MAC Address Base Station learned MAC addresses TTL Time to Live (for datagrams in the network) Interface Type of interface © CalAmp Sentry 4G-90

• CalAmp Sentry 4G-900, 4.4 Alarms and Traps Use the Web Manager to view a summary of the currently generated alarms. You can also disable irrelevant alarms. 4.4.1 Viewing a Summary of System Alarms This read-only screen provides a summary of the current system alarms. To access the Alarms pane 1. Click the Admin menu option and then the Alarms and Traps sub-menu option. From the Alarms and Traps sub-menus choose Alarms. The System Alarms pane is displayed. © CalAmp Sentry 4G-900 Pico Base Station 23

• CalAmp Sentry 4G-900, © CalAmp Sentry 4G-900 Pico Base Station 33 4.5.6.3 Setting the Version to Run from the Primary Directory Click Set as Primary. The software files will run from the Primary directory. The Software Upgrade procedure is now complete.

• CalAmp Sentry 4G-900, Sentry 4G-900 Pico Base Station Operating Manual Copyright © 2010 ALL RIGHTS RESERVED Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized except where expressly permitted. Violations are liable for damages. All rights reserved, particularly for the purposes of patent application or trademark registration. This document contains proprietary information, which is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without prior written consent. Disclaimer Of Liability We have checked the contents of thi

• CalAmp Sentry 4G-900, 3.4 ASN-GW Mode: ASN Settings When the Base Station is in ASN-GW mode, it is required to define the backbone ASN-GW parameters. These include the ASN-GW IP address, tunneling method (between the Base Station and the ASN-GW), and the Base Station ÅÆ ASN keep-alive intervals. 3.4.1 ASN-GW Link Settings This pane provides configuration options for the ASN-GW IP and R6 parameters. To access the ASN-GW Settings pane 1. Click the Backbone menu option and choose ASN Settings and then ASN-GW Settings from the sub-menus. The ASN-GW settings pane is displayed. 2. Define the required parameters according to the following desc

• CalAmp Sentry 4G-900, Table of Contents 1 Introduction .................................................................................................... 1 1.1 Overview .................................................................................................................................... 1 1.2 Features ..................................................................................................................................... 1 2 Getting Started .........................................

More Instructions:

	CalAmp Sentry 4G-900 Installation and setup manual 19-06-2023 31	DOWNLOAD
	CalAmp Sentry 4G-900 Operation & user’s manual 18-04-2023 48	DOWNLOAD

Related Products and Documents (Wireless Router):

Comparable Devices:

Similar Resources:

• Cisco Linksys WAG54G2 (96 pages) USER GUIDEWireless ADSL2+ Modem RouterModels: WAG54G2, WAG160N v2English NederlandsDeutsch PolskiFrançais РусскийΕλληνική TürkçeItalianoﺔﻴﺑﺮﻌﻟﺍENDEFRGRITNLPLRUTRAR …

• NetComm NB5540 (5 pages) Enabling Wireless Security on NB5580W / NB5540using WPA (XP SP2)Step 1.Go to One Page Setup on your NB5580 / NB5540. To do that type in http://192.168.1.1 on your web browser. Step 2.Set Wireless Security to Mandatory and click Settings. …

• Acura ACUCXTM2M (6 pages) ACUCXTM2M Router Quick Guide ACUCXTM2M Router Quick …

• Lexmark 9300 Series (198 pages) 9300 Series All-In-OneUser's GuideSeptember 2006 www.lexmark.comLexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.All other trademarks are the property of their respective owners.© 2006 Lexmark International, Inc.All rights reserved.740 West New Circle RoadLexin …

• Paradyne 6218-A1 SERIES (20 pages) PARADYNE ADSL Wireless Modem Router ManualPage 16218-A1-XXX ManualPARADYNEADSL Wireless Modem Router¾ Do not open the housing!¾ Use only the power supply provided with this device.¾ Use only the cables provided with this device and do not perform any modification on them.Rev 0.1Nov, 25, 200 4 …

• NETGEAR JNR3210 (2 pages) Espere aproximadamente 2 minutos hasta que el módem termine de encenderse.Si el módem dispone de una batería de recambio, extráigala y vuelva a instalarla antes de conectar de nuevo el módem a la toma de corriente.Contenido de la caja:Router inalámbrico N300 Gigabit con USBJNR3210Guía de instalaciónFuente de alimentaciónCable EthernetPaso 1:Desenchu …

Comments, Questions and Opinions: