Canon IMAGERUNNER 2530 Service Manual

Text of Canon IMAGERUNNER 2530 User Guide:

• Canon IMAGERUNNER 2530, 7 7 7-11 7-11 Error Code > Jam Code > Main Unit Error Code > Jam Code > Main Unit Jam Code Main Unit 550-sheet 1st cassette model S1 S5 S7 S19 S12 S42 S40 • F-7-1F-7-1 250-sheet 1st cassette model S5 S7 S19 S12 S42 S40 • F-7-2F-7-2

• Canon IMAGERUNNER 2530, 2 2 2-30 2-30 Technology > Laser Exposure System > Basic Sequence > Basic Sequence Technology > Laser Exposure System > Basic Sequence > Basic Sequence Basic Sequence Basic Sequence When the control panel power switch is turned on, the laser scanner starts to rotate; when the motor rotationreaches its target revolution, the machine turns on the laser unit. Thereafter, when the Start key is turned on, themachine generates the image request signal (PVREQ) on the printer side, and turns on the laser beam withref

• 2 2 2-21 2-21 Technology > Controller System > Controls > Flow of Image Data According to Copy Functions Technology > Controller System > Controls > Flow of Image Data According to Copy Functions Printer unit Output Image Processing Main controller PCB To DC controller PCB Compression/expansion/editing block Binary density conversion Enlarge

• Canon IMAGERUNNER 2530, 2 2 2-28 2-28 Technology > Laser Exposure System > Construction > Main Conguration Parts Technology > Laser Exposure System > Construction > Main Conguration Parts Laser Exposure System Construction Specications/Controls/Functions Laser light The number of laser light 2 Output 5mW Wave length 785nm - 800nm (Infrared laser) Scanner motor Motor type DC brushless motor The number of rotation Approx 32000rpm (1-speed control) Type of bearing Oil Polygon mirror The number of face 6 (Φ40) Controls Synchronous control Main

• Canon IMAGERUNNER 2530, 8 8 8-15 8-15 Service Mode > Details of Service Mode > #NUMERIC > Details Service Mode > Details of Service Mode > #NUMERIC > Details <025: Answering machine connection function signal detection time> Sets the signal detection time for the answering machine connection function operation. When the answering machine connection function is operating, if the function does not operate normally because the fax does not detect CNG signal sent from the line, raise this parameter to increase the signal detection time. <

• Canon IMAGERUNNER 2530, 8 8 8-22 8-22 Service Mode > Details of Service Mode > #SCAN > READER Service Mode > Details of Service Mode > #SCAN > READER Bit Name Display contents Remarks Bit1 Document tray width sensor 1 (PI1) 1: Document present Bit2 Not used. Bit3 Not used. Bit4 Delivery reversal sensor (PI6) 1: Document present Bit5 Read sensor (PI7) 1: Document present Bit6 Not used. Bit7 Registration sensor (PI8) 1: Document present Bit8 Document length sensor 2 (PI5) 1: Document present Bit9 Document length sensor 1 (PI4) 1: Document present Bit10 Not used. Bit11 Cover open/closed sensor (PI10) 1: Open Bit12 Last document detection se

• Canon IMAGERUNNER 2530, 9 9 9-29 9-29 Installation > Card Reader Installation Procedure > Registering the Card IDs Installation > Card Reader Installation Procedure > Registering the Card IDs Registering the Card IDs After installing the Card Reader, register the card numbers to be used in the service mode of the host machine. If they are not registered, cards will not be recognized when inserted. 1) Plug the power cord into the outlet. 2) Turn on the main power switch. 3) When a message appears on the control panel display, press the following keys to enter the service mod

• Canon IMAGERUNNER 2530, 9 9 9-84 9-84 Installation > Relocating the Machine > Work Procedure Installation > Relocating the Machine > Work Procedure Relocating the Machine Required Articles Have the following articles on hand: Fixing tape Drum cover removed during installation Optical system xing screws (2 pcs.) removed during installation (iR2545/2535 Series only) Preparation for Relocating the Machine When moving the machine using stairs (including steps) or transporting the machine to a different place using a truck, go through the steps described below. CAUTION: When lifti

• 1 1 1-3 1-3 Product Overview > Product Lineup > Option > Pickup delivery / image reading options Product Overview > Product Lineup > Option > Pickup delivery / image reading options Option Pickup delivery / image reading options [4] [2] [1] [3] [5] [6] [7] [8] [11] [9] [10] [12] [13] [14] [15] [16] [17] [18] [20] [19] [21] [22] [23] F-1-3F-1-3 No. Pr

• 4 4 4-34 4-34 Parts Replacement and Cleaning > Consumable Parts Requiring Periodic Replacement > Removing the Waste Toner Container Parts Replacement and Cleaning > Consumable Parts Requiring Periodic Replacement > Removing the Waste Toner Container Consumable Parts Requiring Periodic Replacement Removing the Transfer Roller 1) Open the right cover. 2) Remove the transfer roller. -

• Canon IMAGERUNNER 2530, 8 8 8-12 8-12 Service Mode > Details of Service Mode > #MENU > Deatails Service Mode > Details of Service Mode > #MENU > Deatails SSSW-SW35 List of Functions Bit Function 1 0 0 e-RDS function ON/OFF Yes No 1 Call button function ON/OFF Yes No 2 ScanToMeia function enable/disable enable disable 3 MediaPrint function enable/disable enable disable 4 IC card authentication management function ON/OFF Yes No 5 not used - - 6 not used - - 7 not used - - Detailed Discussions of Bit 0 Select whether to set the e-RDS function. When "1" is selected, the function is set. When "0" is selected, the function is not set. Detailed Discussions of Bit 1 S

• Canon IMAGERUNNER 2530, 7 7 7-3 7-3 Error Code > Error Code > Error Code Details Error Code > Error Code > Error Code Details Error Code Error Code Details Ecode Detail Code Item Description E000 0001 Title Fixing temperature abnormal rise Description The temperature detected by the main thermistor does not rise to the specied value during startup control. Remedy 1.Go through the following to clear the error: CLEAR > ENGIN > ERRCLR; and then turn OFF and then ON the power. 2.Check connection of the Connector

• Canon IMAGERUNNER 2530, 9 9 9-11 9-11 Installation > Making Pre-Checks > Selecting the Site of Installation Installation > Making Pre-Checks > Selecting the Site of Installation Connecting the cord MEMO: Install an optionally available document glass cover or the DADF on the machine. If the model is the one without the DADF, install a document cover glass. For how to install the DADF, refer to the DADF Installation Procedure. 1) Insert the connector of the supplied Power cord into the AC inlet. F-9-20F-9-20 2) Install the suppl

• Canon IMAGERUNNER 2530, 9 9 9-15 9-15 Installation > Making Pre-Checks > Selecting the Site of Installation Installation > Making Pre-Checks > Selecting the Site of Installation b.Afxing the ADF Label (only for the standard model with an ADF) 1) If the following labels are supplied, go through the steps described below. Document size label Finger pinch caution label 1 Finger pinch caution label 2 • • • 2) Align the side guide (rear) with the A4/A3 mark. A4/A3 F-9-28F-9-28 3) Afx the document size label [A] of the suitable paper size series to the feeder cover in such a manner

• Canon IMAGERUNNER 2530, 4 4 4-29 4-29 Parts Replacement and Cleaning > Main Units/Parts > Removing the Toner Supply Unit > Action to Take after Replacement Parts Replacement and Cleaning > Main Units/Parts > Removing the Toner Supply Unit > Action to Take after Replacement Removing the Toner Supply Unit 1) Remove the inside base cover.("Removing the Inside Base Cover"(page 4-17). ) 2) Remove the left cover.( "Removing the Left Cover"(page 4-16). ) 3) Remove the waste toner container. 4) Remove the drum unit.( "Removing the Waste Toner Container"(page 4-34). ) 5)Remove the toner bottle. 6) Remove the toner supply cover.( "Removing the Toner Supply

• Canon IMAGERUNNER 2530, 2 2 2-19 2-19 Technology > Controller System > Controls > Construction of the Image Processing Module Technology > Controller System > Controls > Construction of the Image Processing Module Controls Flow of Image Data - SEND - FAX - PullScan - E-Mail - PDL Print PC Original Copy A A A Print output Scan Image data Other iR machine F-2-32F-2-32 Construction of the Image Processing Module Main controller PCB Processes image data for output to the printer unit. Printer unit output image processing block DC controller PCB Reader relay PCB SO-DIMM - image memory - program (temporary storage) Processes the image da

• Canon IMAGERUNNER 2530, 9 9 9-8 9-8 Installation > Making Pre-Checks > Selecting the Site of Installation Installation > Making Pre-Checks > Selecting the Site of Installation Installing the Toner Bottle 1) Open the toner supply cover. F-9-7F-9-7 2) Raise the lock lever. F-9-8F-9-8 3) Unpack the new toner bottle, and then remove the cap. F-9-9F-9-9 4) Insert the toner bottle into the machine. F-9-10F-9-10 5) Lower the lock lever to secure the toner bottle. MEMO: Turn the lock lever until it becomes level. If the lock lever is stopped in the middle, toner cannot be supplied normally. 6) Close the toner supply cover.

• 9 9 9-50 9-50 Installation > Cst Heater Kit-J1 Installation Procedure > Installation Procedure Installation > Cst Heater Kit-J1 Installation Procedure > Installation Procedure 16) Clamp the harness in the 4 wire saddles. 17) Joint the connector of the heater DC harness to J113B on the power supply unit. x4 CAUTION: Scatter the slack of the wire and comrm which the d

• 5 5 5-3 5-3 Adjustment > Adjustment when replacing parts > Scanning System > Action to Take after Replacing the Platen Glass Adjustment > Adjustment when replacing parts > Scanning System > Action to Take after Replacing the Platen Glass Adjustment when replacing parts Scanning System Action to Take after Replacing the CIS Unit After replacing the CIS unit, make the following adj

• Canon IMAGERUNNER 2530, 2 2 2-60 2-60 Technology > Pickup Feed System > Controls > Cassette Pickup Assembly (550-sheet 1st cassette model) Technology > Pickup Feed System > Controls > Cassette Pickup Assembly (550-sheet 1st cassette model) Controls Overview Duplex Feed Control Fixing / Registration Assembly Multi-Purpose Pickup Assembly Cassette Pickup Assembly Area Detection, Control Cassette Pickup Assembly Outline Paper Level / Presence Detection Paper Size / Cassette Presence Detection Multi-Purpose Pickup Assembly Outline

• Canon IMAGERUNNER 2530, 4 4 4-9 4-9 Periodical Service > List of Parts > List of Motors Periodical Service > List of Parts > List of Motors List of Motors M31 M2 M1 M3 M7 M6 M10 F-4-8F-4-8 Symbol Part name Part number Reference M1 Main Motor FK2-9141 - M2 Fixing Motor FK2-9145 - M3 Cassette 1 Pickup Motor FK2-7327 - M6 Bottle Motor FK2-9147 - M7 Hopper Motor FK2-9147 - M10 Reversal Motor FK2-9150 - M31 Scanner Motor FK2-1066 - T-4-7T-4-7

• Canon IMAGERUNNER 2530, 9 9 9-75 9-75 Installation > Drum Heater-C1 Installation Procedure > Installation Procedure Installation > Drum Heater-C1 Installation Procedure > Installation Procedure 8) Hold the drum unit as shown in the gure. Pull up the unit a little and draw it out completely. F-9-171 9) Remove the 2 screws and release the claw to detach the toner replenish cover. Claw x2 x1 F-9-172 10) Detach 1 connector and draw the developing unit out. x1 F-9-173 11) Dismount the harness from the developing stay and remove 2 screws to detach the developing stay. (Removed developing stay is no longer use

More Instructions:

	Canon IMAGERUNNER 2530 Operation & user’s manual 13-03-2024 582	DOWNLOAD
	Canon IMAGERUNNER 2530 Copying manual 10-11-2023 114	DOWNLOAD
	Canon IMAGERUNNER 2530 Service manual digest 05-05-2023 116	DOWNLOAD
	Canon IMAGERUNNER 2530 Reference manual 07-04-2023 264	DOWNLOAD

Related Products and Documents (All in One Printer):

Comparable Devices:

Similar Resources:

• Lexmark T652 (588 pages) Lexmark™ T650, T650n, T652dn,T654dn & T656dne Printer4062-XXX• Table of contents• Start diagnostics• Safety and notices• Trademarks•IndexLexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.Edition: September 17, 2009 …

• Kyocera C5020N - FS Color LED Printer (2 pages) EF-310 Installation GuideFS-3900DN/FS-4000DN/FS-3920DN/FS-4020DN/EP 370DN/EP 470DNFS-1900/FS-1920/FS-3820N/FS-3830N/FS-C5016N/FS-C5020N/FS-C5025N/FS-C5030N1234512 3 476 …

• Brother DR8000 (2 pages) Replacing Brother DR8000 Drum Unitwww.ImageMaker.com.sg Page 1Replacing the Drum UnitThe FAX/MFC uses drum unit to create print images on paper. If LCD shows CHANGE DRUM SOON, the drum unit is near end of its life. Purchase a new Image Maker drum unit to replace the current one.Even the LCD shows CHANGE DRUM SOON, you may be able to continue to print without …

• Ricoh PRIPORT JP730 (4 pages) Replacing the Paper Feed Roller andthe Separation Pressure PadIf paper misfeeds or double-feeds are occurring frequently, first try clean-ing the paper feed roller, and then check that you are using the correctfeed roller pressure and separation pressure (refer to Operating Instruc-tions).When the problem persists even after you have done the above, replacet …

• Toshiba e-studio2330c (512 pages) SERVICE HANDBOOKMULTIFUNCTIONAL DIGITAL COLOR SYSTEMSe-STUDIO2330C/2820C/2830Ce-STUDIO3520C/3530C/4520CModel: FC-2330C/2820C/2830C/3520C/3530C/4520CPublish Date: March, 2008File No. SHE070001E0R070921E3700-TTECVer05_2009-01 …

• Epson L3160 (4 pages) Start HereIMPORTANT: Before using this product, make sure you read these instructions and the safety instructions in the online User’s Guide.1 UnpackNote: Do not open the ink bottles until you are ready to fill the ink tanks. The ink bottles are vacuum packed to maintain reliability. Remove all protective materials from the product.Note: Do not turn on t …

Comments, Questions and Opinions: