IDS X64 Installer Manual
|
IDS X64, IDS X64 Remote Receiver 700-408-02A Issued August 2010 3 Contents 1. Overview .......................................................................................................................... 4 1.1 Introduction .............................................................................................................................. 4 1.2 Features ................................................................................................................................... 4 1.3 Wiring and Configuration ........
Section: 1 IDS X64 Remote Receiver 700-408-02A Issued August 2010 4 1. Overview 1.1 Introduction The IDS X64 Remote Receiver is a 433.92 MHz RF receiver that is designed to connect to an IDS X64 Alarm Pane
IDS X64, Section: 1 IDS X64 Remote Receiver 700-408-02A Issued August 2010 5 1.3 Wiring and Configuration NOTE: The amber LED will be a steady on when it is connected to the Bus. If it is off, then there is a problem. The green LED flashes when in standby mode. 1.4 Installation Choose a location for the Remote Receiver: as high as possible accessible for installation and maintenance accessible for X64 wiri
IDS X64, Section: 1 IDS X64 Remote Receiver 700-408-02A Issued August 2010 6 D+ WHITE D- GREEN (These colours are only a guideline). 5. Equipment to be remotely switched should be connected to the RELAY1 and RELAY2 terminals of the Remote Receiver. The relay current ratings (see section 1.5) must not be exceeded. If the Remote Receiver relays are configured as "secure", the effective terminals for "NC" (Normally Closed) and "NO" (Normally Open) will be swapped. 6. Keep the Remote Receiver cover off during configuration, so that the DIPswitches are accessible and the LEDs are visible. 7. When configu
IDS X64, Section: 2 IDS X64 Remote Receiver 700-408-02A Issued August 2010 7 Button 3: Stay Arm Button 4: no function NOTE: When any button is held down for 3 seconds, the panel goes into panic mode. Pressing the arm/disarm button does NOT cancel the panic. The panic needs to be cancelled at the keypad. 2.2 Management Button The management button allows for the ability to assign more than one user per remote. You can also have two users from two different partitions on the same remote. This is done by the Remote Receiver's "Add Remote to Panel - Advanced" menu, by specifying the
IDS X64, Section: 2 IDS X64 Remote Receiver 700-408-02A Issued August 2010 8 UUUU – User Code RR – Remote Receiver Record Number UUU – Number of Users TTTT – Pulse Time RT – Remote Receiver These terms will be used in bold in the document so that they can stand out. 2.4 Number Assignment Each Remote Receiver must be assigned a number to specify the destination of commands from the panel. Allowable Remote Receiver numbers are 1, 2, 3, or 4. Each Remote Receiver must have a different number; multiple assignmen
IDS X64, Section: 2 IDS X64 Remote Receiver 700-408-02A Issued August 2010 9 2.5 Add Remote to Panel Use the following steps to add Remote Transmitters to the Remote Receiver connected to an IDS Alarm Panel via the keypad Bus. [*] [Master Code] [*] [2] [0] [*] [Receiver Number] [*] [User Code] [*] [*] [Press RT Button] [#] LCD Keypad 1. Defaulting of the Remote Receiver is only for new installations of the Remote Receiver. 2. On the Alarm Panel, ADD the user codes that will be assigned to the Remote Receivers (one for each). Do this only if the codes have not already been entered before. 3. Hold the [*] key until the
IDS X64, Section: 2 IDS X64 Remote Receiver 700-408-02A Issued August 2010 10 Remote Receiver 4 is indicated by zone LED 3 coming on. 11. Enter [USER CODE] followed by the [*] key. 12. The READY and POWER LEDs flash simultaneously, and the ARM and AWAY LEDs are on. 13. Press the [*] key to proceed, or the [#] key to abort. 14. Press and hold the remote button. 15. The ARM and AWAY LEDs flash simultaneously, and the READY and POWER LEDs flash simultaneously. 16. Release the remote button. 17. The ARM and AWAY LEDs flash simultaneously, and the READY and POWER
Section: 2 IDS X64 Remote Receiver 700-408-02A Issued August 2010 11 18. The keypad displays “Success”, “Rt User R M B”. 19. Press the [*] key to return to steps 9-18 if you wish to add more remotes. 20. Once you have finished, press the [#] key to exit programming. NOTE: If you were unsuccessful, the keypad will display “fail”. I
IDS X64, Section: 2 IDS X64 Remote Receiver 700-408-02A Issued August 2010 12 deleted before reprogramming. If the users are not deleted then the Remote Transmitter will continue to operate in management button mode. 2.7 Delete Remote from Panel Use the following steps to add Remote Transmitters to the Remote Receiver connected to an IDS Alarm Panel via the Keypad Bus. [*] [Master Code] [*] [2] [2] [*] [Receiver Number] [*] [User Code] [*] [#] LCD Keypad 1. Hold the [*] key until the beep (3-4 seconds). 2. The keypad displays “Master Code + *”.
Section: 2 IDS X64 Remote Receiver 700-408-02A Issued August 2010 13 10. The ARM and AWAY LEDs flash simultaneously, and the READY and POWER LEDs flash simultaneously. 11. Once you have finished, press the [#] key to exit programming. 2.8 Set Remote Receiver Button Properties Use the following steps to se
IDS X64, Section: 2 IDS X64 Remote Receiver 700-408-02A Issued August 2010 14 Zone LED Property Zone LED Property 1 Relay 1 9 2 Relay 2 10 3 Arm / Disarm 11 4 Stay Arm 12 5 Panic 13 6 14 7 15 8 16 11. Enter [PROPERTY NUMBER] you would like to toggle, followed by the [*] key. NOTE: Arm/disarm, stay arm, and panic are mutually exclusive, selecting one de-selects the others. To confirm if arm/disarm is set for button 1, LED 3 will be on and LED 4 will be off. If stay is set for button 1, then LED 3 will be off and LED 4 will be on. I
IDS X64, Section: 2 IDS X64 Remote Receiver 700-408-02A Issued August 2010 15 LED Keypad 1. Hold the [*] key until the beep (3-4 seconds). 2. The READY and ARM LEDs flash alternately. 3. Enter [MASTER CODE] followed by the [*] key. 4. The READY LED flashes. 5. Enter [2] [4] followed by the [*] key. 6. The READY and ARM LEDs flash simultaneously. 7. Enter [RECEIVER NUMBER], which could be 1, 2, 3, or 4, followed by the [*] key. 8. The READY and AWAY LEDs flash simultaneously, and the ARM LED is on. 9.
IDS X64, Section: 2 IDS X64 Remote Receiver 700-408-02A Issued August 2010 16 8. The keypad displays “Remote Receivr N”, “R MM:SS”. 9. Enter [RELAY PULSE TIME] followed by the [*] key. 10. The keypad displays “R time”. 11. Once you have finished, press the [#] key to exit programming. LED Keypad 1. Hold the [*] key until the beep (3-4 seconds). 2. The READY and ARM LEDs flash alternately. 3. Enter [MASTER CODE] followed by the [*] key. 4. The READY LED flashes. 5. Enter [2] [5] followed by the [*] key. 6. The READY and ARM LEDs flash simultaneously. 7. Enter [RECEIVER NUMBER], which could be 1, 2, 3
IDS X64, Section: 2 IDS X64 Remote Receiver 700-408-02A Issued August 2010 17 5. Enter [2] [6] followed by the [*] key. 6. The keypad displays “Receiver Num + *”. 7. Enter [RECEIVER NUMBER], which could be 1, 2, 3, or 4, followed by the [*] key. 8. The keypad displays “Remote Receivr N”, “Confirm with *”. 9. Press the [*] key. 10. The keypad displays “Receiver Num + *”, “Defaulted Rx N”. 11. To default additional receivers, repeat steps 7-10. 12. Once you have finished, press the [#] key to exit programming. NOTE: The keypad will beep 3 times and then repeat the be
IDS X64, Section: 2 IDS X64 Remote Receiver 700-408-02A Issued August 2010 18 5. Enter [2] [7] followed by the [*] key. 6. The keypad displays “Receiver Num + *”. 7. Enter [RECEIVER NUMBER], which could be 1, 2, 3, or 4, followed by the [*] key. 8. The keypad displays “Receiver Num + *”, Identifying Rx N”. NOTE: The keypad will beep 3 times and then repeat the beeps if the receiver is not registered. The receiver will flash both its green and red LEDs in sync. The LEDs will be pulsed on for 200ms, and then off for 200ms. This will
Section: 2 IDS X64 Remote Receiver 700-408-02A Issued August 2010 19 LCD Keypad 1. Hold the [*] key until the beep (3-4 seconds). 2. The keypad displays “Master Code + *”. 3. Enter [MASTER CODE] followed by the [*] key. 4. The keypad displays “Option Menu”, “Add User Code”. 5. Enter [2] [8] followed by the [*] key. 6. The keypad displays “Receiver
IDS X64, Section: 2 IDS X64 Remote Receiver 700-408-02A Issued August 2010 20 LED Keypad 1. Hold the [*] key until the beep (3-4 seconds). 2. The READY and ARM LEDs flash alternately. 3. Enter [MASTER CODE] followed by the [*] key. 4. The READY LED flashes. 5. Enter [2] [9] followed by the [*] key. 6. The READY and ARM LEDs flash simultaneously. 7. Enter [RECEIVER NUMBER], which could be 1, 2, 3, or 4, followed by the [*] key. 8. The READY and ARM LEDs flash simultaneously. Zone Led Receiver No. Zone Led Capacity
IDS X64, Section: 3 IDS X64 Remote Receiver 700-408-02A Issued August 2010 21 3.2 Warnings All known Remote Transmitters send the same set of button codes, but the button position for a given button code varies between manufacturers. NOTE: If Remote Transmitters of various types are used on a system, a person operating someone else's Remote Transmitter might get unexpected results. It is therefore recommended that all Remote Transmitters used on a system be identical. Remote Receivers in a system could
IDS 400 Receiver Operation & user’s manual
400 |
IDS X64 Receiver Installer manual
X64 |
IDS X Series Receiver Operation & user’s manual
X Series |
IDS 816 Receiver Installer manual
816 |
IDS IDS805 Receiver Quick start manual
IDS805 |
IDS LCD Digital Keypad Receiver Operation & user’s manual
LCD Digital Keypad |
IDS 1632 Receiver Operation & user’s manual
1632 |
IDS 1632 Receiver Installer manual
1632 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Bose | LIFESTYLE T10 | Operating manual | bose/lifestyle-t10-4LW.pdf | 12 Dec 2022 | 92 | 15.77 Mb |
2 | Altec Lansing | 1569A | Operating instructions | altec-lansing/1569a-4GL.pdf | 09 Nov 2022 | 4 | |
3 | Toshiba | IK-WB02A - PoE Network Camera | Specifications | toshiba/ik-wb02a-poe-network-camera-2QO.pdf | 16 Aug 2022 | 2 | 1.02 Mb |
4 | RTC | DFC | Manual | rtc/dfc-TQK.pdf | 16 Oct 2022 | 7 | |
5 | 3M | FAP01-RS | Operation & user’s manual | 3m/fap01-rs-73H.pdf | 18 Jun 2023 | 4 | 0.28 Mb |
6 | Kenwood | KCA-RC55MR | Instruction manual | kenwood/kca-rc55mr-S26.pdf | 30 Jun 2023 | 5 |
Schwarzbeck
RC Option Datasheet 1/6 Rev. C 0705.140116 NSLK/NNLK 81xx Netznachbildungen mit Option RC für Messempfänger NSLK/NNLK 81xx LISN with option RC for EMI measurement receivers Beschreibung: Description: Mittels der Option RC kann die Netznach-bildung per Fernsteuerung von einem geeigneten Messempfänger umgeschaltet werden. Die Option …
NSLK 81 Series(6 pages) |
Sony
1SERVICE MANUALUS ModelCanadian ModelSTR-DE595AEP ModelUK ModelE ModelAustralian ModelKorean ModelSTR-DE495/DE595STR-DE495/DE595FM STEREO/FM-AM RECEIVERAUDIO POWER SPECIFICATIONSPOWER OUTPUT AND TOTALHARMONIC DISTORTION:With 8 ohm loads, both channels driven, from40 – 20,000 Hz; rated 90 watts per channelminimum RMS power, with no more than0.09 % total har …
STR-DE495(14 pages) |
SwissPhone
1User manualDear customer,congratulations to the DiCal-ToM, the new Swissphone-POCSAG-Desktop-Receiver. It’s a state-of-art device with a 7” Touch-Screen monitor. The ToM impresses by a combination of intuitive usage, text visualization in different sizes and styles, MP3 sounds, printing-, audio- and relay-output capabilities.The parameters for the …
DiCal-ToM(24 pages) |
STEINEL
21 3FE 8100i9540600GerätebeschreibungDer FE 8100 empfängt Funksignale von bis zu 8 STEINEL-Funk-Sendern mit verschiedenen Adressen undschaltet dann den angeschlossenen Verbraucher (z. B. eine Leuchte). Der Funk-Empfänger reagiert nur aufSender, die ihm vorher zugeordnet worden sind. Weitere Informationen zur Einstellung von Sendern undEmpfängern entnehme …
FE8100(3 pages) |
Zodiac
DZR-1700FTA PLUSFree-To-Air Ricevitore Satellitare Digitale Ricevitore Satellitare Digitale Digital Satellite Receiver Receptor Satélite Digital Récepteur Satellite Numérique Manuale d’uso User’s manual Manual de Empleo Manuel d'utilisation
…
DZR-1700FTA PLUS(87 pages) |
Samson
U H F W I R E L E S S S Y S T E M• AL1 Presentation Transmitter• AX1 Handheld Transmitter• CR77 ReceiverOWNERS MANUAL PRESENTATIONTRANSMITTERHANDHE LD TR ANS MIT TER
…
CR77 Receiver(84 pages) |
Roper Cooktop RangeInstallation instructions manual for Roper Range Cooktop Range, 7 |
Polaroid Car Video System Overhead DVD PlayerOverhead DVD Player Operation & user’s manual - 2N5154 Overhead DVD Player, 29 |
Flymo Lawn Mower GT500User Guide: Flymo GT500 (VC5MD5, Upd.19/01/2024) GT500, 14 |
Directed Audio Amplifier 1500X1500X Owner's manual - 361A4V 1500X, 15 |
Carson Toy FY5 DestroyerlineCarson FY5 Destroyerline Toy Instruction manual FY5 Destroyerline, 40 |
Whirlpool Refrigerator 2199011Refrigerator PDF Refrigerator use & care manual 2199011, 43 |
Vitek Other VTQ-C04 - 09-2001Other #51VK72 VTQ-C04 - 09-2001, 4 |
Craftsman Accessory 225.582590Manual: Craftsman 225.582590 (Z73D5H, Upd.29th Jan 2024) 225.582590, 58 |
Nortel PBX Meridian Mail#J9W1F7 Meridian Mail: Nortel PBX Owner Documentation Meridian Mail, 2 |
Dayton Fan 2ATX6PDF Guide (@6S1SWU), Dayton 2ATX6 Fan (24.12.2023) 2ATX6, 12 |
Elkay Indoor Furnishing Lustertone LFRQ1313Elkay Indoor Furnishing Lustertone LFRQ1313 Specifications Lustertone LFRQ1313, 1 |
Sammic Food Saver TS-150Manual: Sammic TS-150 (KB2S8K, Upd.13th Dec 2023) TS-150, 12 |