Manualios.com

BCS SD03 speed dome 66 Installation Manual

  • SD03 speed dome 66 Security Camera
  • mamsPB6D6Vne6
  • Installation Manual
  • PDF / Adobe Acrobat Reader
  • 25

BCS SD03 speed dome 66 Manual Online:

4.7, 1669 votes
BCS SD03 speed dome 66 User Manual
BCS SD03 speed dome 66 User Guide
BCS SD03 speed dome 66 Online Manual

Text of BCS SD03 speed dome 66 User Guide:

  • BCS SD03 speed dome 66, 2 SPEED DOME INSTALLATION 2.1 General Introduction Speed dome consists of the following components. See Figure 2-1. Speed Dome Cover Component Body Component External Cover Component Figure 2-1 2.2 Hanging Bracket Speed Dome Installation 2.2.1 Installation Requirement The hanging bracket is suitable for indoor or outdoor hard wall structure. The wall thickness shall support the expansion bolt. The wall shall support the 4x speed dome weight. 2.2.2 Hanging Bracket Installation Draw the hole position in the wall in accordance with the hanging bracket bottom installation pole. Then dig holes. Please refer to

  • BCS SD03 speed dome 66, 22 OFF OFF 9600bps ON OFF 4800bps OFF ON 2400bps ON ON 1200bps Please refer to the parity setup sheet for detailed information. 7 8 Parity OFF OFF NONE ON OFF EVEN OFF ON ODD ON ON NONE 3.2 Set address dial switch The encode mode adopts binary system. 1 to 8 is valid bit. The highest address bit is 255. You can refer to the following sheet for more information. Address 1 2 3 4 5 6 7 8 1 OFF OFF OFF OFF OFF OFF OFF OFF 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF

  • Figure 2-2 You can use socket head cap screw to fix hanging bracket and external cover component. (Please install waterproof sealing cushion) 10 M5×12 socket head cap screw Hanging Bracket External Cover Component Figure 2-3 After you installed bracket and external cover components, loosen captive screws and open the pane

  • BCS SD03 speed dome 66, Teflon tape M4 Screw Silica gel Figure 2-21 Please loosen the M4 bolt at the splicing sleeve of pole bottom (just a little will be O.K), then turn the screw thread of the upper cover splicing sleeve in. Now pull the power cable through the upper cover and then turn the upper cover to the pole splicing sleeve firmly. Fix the M4 bolt. Loosen the captive screw in the panel. See Figure 2-22. Please note, if the speed dome is installed in outdoor environment, please enlace enough Teflon tape at the screw thread of pole and then turn the pole to the connection flange firmly. Please use silica gel to secure

  • BCS SD03 speed dome 66, 4 Important Safeguards and Warnings Safety Measures Qualified Engineer Needed z The installation engineer or maintenance engineer shall have corresponding CCTV system installation certificate or maintenance qualification certificate. z The installation engineer or maintenance engineer shall have qualification certificate for work at height. z The installation engineer or maintenance engineer shall have the basic knowledge and operation technique for low-voltage cable layout and low-voltage electronic cable connection. z Please read the installation manual carefully and keep it well for future reference, z We are not liable f

  • BCS SD03 speed dome 66, 6 1 INSTALLATION 1.1 Installation Preparation Basic Requirement z All installation and operation here should conform to your local electrical safety codes. z Before installation, please open the package and check all the components are included. Please make sure the speed dome installation environment and installation mode can meet your requirement. If there is special requirement, please contact your local retailer for more information. z We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation. Check installation space and installatio

  • 2 Table of Contents 1 INSTALLATION................................................................................................... 6 1.1 Installation Preparation .........................................................................................................................6 1.2 Installation Mode.........................................................................

  • BCS SD03 speed dome 66, 5 Do not try to dismantle or modify the device z There is risk of personal injury or device damage resulting from opening the shell. z Please contact your local retailer if there is internal setup or maintenance requirement. z We are not liable for any problems caused by unauthorized modifications or attempted repair. Do not allow other object falling into the device z Please make sure there is no metal or inflammable, explosive substance in the speed dome. z The above mentioned objects in the device may result in fire, short-circuit or damage. z Please shut down the device and disconnect the power cable if there is water or liquid falling into the camer

  • BCS SD03 speed dome 66, Figure 4-3 Name Function AC24V 24V power port. Connect to the power cable. EARTH Ground port. AC24V 24V power port. Connect to power cable. Extension RS 485 port is shown as in Figure 3-4. Figure 4-4 Name Function + Extension peripheral 485 port. Such as control temperature, humidity sensor. 485 - Extension peripheral 485 port. Such as control temperature, humidity sensor. GND Ground port. +12V External device power port. Provide power the Peripheral. 4.2 Alarm Cable Connection Open the dome cover and take PTZ chip core out. Turn the core upside

  • BCS SD03 speed dome 66, Without wire slot With wire slot Figure 2-19 Loosen the M4 bolt in the flanges side. Separate the connection flange and pole and then pull the power, video/control, alarm cable out of the seal groove of flanges bottom side, and then lead them through the flanges central hole. Now you can fix the flange in the ceiling. See Figure 2-20. Please note, if the speed dome is installed in outdoor environment. Please use silica gel to secure waterproof between the flange and ceiling, and position near wire slot. Connection Flange Silica gel Figure 2-20 Now please follow Figure 2-21 to pull the power cable through the pole and t

  • BCS SD03 speed dome 66, 4 Cable Connection 4.1 RS485 and Power Cable Connection There are three cable groups: power cable, RS 485 and video cable. Draw out the cables from the dome to connect with main control devices (such as monitor, control keyboard, DVR and etc.) and power adapter. See Figure 3-1 and Figure 3-2. 23 Figure 4-1 Figure 4-2 Name Function A 485-A. It is to control dome built-in PTZ. B 485-B. It is to control dome built-in PTZ. 485 GND Ground. OUT Reserved audio port. Audio output port. GND R

  • BCS SD03 speed dome 66, Cable Heatin g Stri p Steel Safety Rope Figure 2-8 Please refer to Figure 2-9 to install bottom cover. Please line the two round grooves of bottom cover side to the two captive screws on the bottom cover side. The angel shall ranges from -5 degrees to +5 degrees. Then you can push the bottom cover up and fix the captive screws. You can find the lubricating grease in the accessories package. Round grooves Captive Screws Lubricating Grease Figure 2-9 2.3

  • BCS SD03 speed dome 66, 25 Name Function Alarm out:1-2 z Two alarm output channels. When there is an alarm from current channel, system activates relay or not. z Alarm output relay default setup is NO. You can use the jump-cap near the power board relay to set. z NO:Normal open alarm output. z NC:Normal close alarm output. GND Alarm input ground end. Alarm in:1-7 z Seven alarm input channels. It is to receive relay signal from the external alarm source. You can go to dome menu to activate specified preset or patter. z When the activation mode is NO (normal open), dome alarms when there is low voltage. High voltage will not a

  • BCS SD03 speed dome 66, Bottom cover connection: Please refer to Figure 2-8. Camera installation: Please refer to Figure 2-7. Bottom cover installation: Please refer to Figure 2-9. After you completed the above steps, the corner installation is shown as in Figure 2-13. Figure 2-13 2.4 Pole Bracket Speed Dome Installation 2.4.1 Installation Requirement The pole installation speed dome is suitable for indoor or outdoor hard structure pole environment. The diameter of pole structure shall comply with the installation dimension of clamp. Default factory clamp is six inches

  • BCS SD03 speed dome 66, 17 Figure 2-17 2.5 Suspended Bracket Speed Dome Installation 2.5.1 Installation Requirement Suspended bracket speed dome installation is suitable for indoor or outdoor hard structure ceiling. The ceiling thickness can install expansion bolt. The ceiling shall support the 4x speed dome weight. 2.5.2 Accessories Installation The installation accessories are shown as in Figure 2-18. Straight Pole Connection Stud Connection flange (With wire slot.) Connection flange (Without wire slot) Figure 2-18 Suspended bracket mainly is connection flange (

  • BCS SD03 speed dome 66, Figure 2-4 Then please follow Figure 2-5 to insert the power pin, video/control pin, alarm cable pin to the corresponding sockets in the outlet. Note: Please make sure the power is disconnected when you connect the power cable. After you connected the cable to the power, please check LED light in the power panel is on or not. You can refer to the error definition sheet for detailed information. Do remember fixing the captive screws after you closed the panel. 11

  • Please use your hand to hold the camera and then adjust the lock tab between the camera and the panel. 1— Captive screw and semi-circle groove. 2— AMP socket connector 3/4/5- three pilot spool You can refer to Figure 2-7 for detailed information. Now please turn the camera in the lock direction until the lock tab of the camera fixing bracket meets the lock

  • BCS SD03 speed dome 66, Figure 1-2 1.2.2.3 Pole Installation Pole installation is suitable for indoor and outdoor hard pole structure. See Figure 1-3. Please refer to chapter 2.4 for detailed information. 8 Figure 1-3 1.2.2.4 Suspended Installation The suspended installation has the following two types. Please refer to chapter 2.5 for detailed information. See Figure 1-4. With Pole Without Pole Figure 1-4

  • BCS SD03 speed dome 66, 2.4.2 Pole Bracket Installation Please refer to Figure 2-15 to install clamp and pole bracket. Pull the cable out of the pole accessories and then use clamp to fix the pole accessories to the pole. Finally, you can use glass cement to the output hole to secure waterproof. Figure 2-15 After you installed bracket and external cover, loosen the captive screws and open the panel, pull the power cable through the hanging bracket and then fix the hanging bracket to the wall. Please pay attention to the waterproof between the bracket and the wall. See Figure 2-16. Figure 2-16 Cable connect

  • BCS SD03 speed dome 66, z Embedded installation z In-ceiling installation z Bracket installation 1.2.2 Bracket Installation Mode The bracket installation consists of the following modes: z Hanging installation z Corner installation z Pole installation z Suspended installation The bracket installation is suitable for indoor and outdoor environment. The outdoor speed dome has a sun-shade cover and it also has an internal heater device. The outdoor speed dome IP standard is IP 66. 1.2.2.1 Hanging Installation This series instal

  • 3 Protocol, Baud Rate, Address setup Before you operate, you need to set protocol, baud rate and address. Otherwise you can not control the product! 3.1 Protocol and Baud Rate Setup Please configure the following settings before begin controlling dome: z Protocol z Baud rate z Address Note: Please reboot the speed dome to get all the setups activated! Open t

Related Products and Documents (Security Camera):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 GE PROFILE PERFORMANCE SERIES ZET837BBBB Specifications ge/profile-performance-series-zet837bbbb-UQ5.pdf 09 Dec 2022 2 0.04 Mb
2 Philips 579008716 Operation & user’s manual philips/579008716-AY3.pdf 01 Feb 2024 38 3.47 Mb
3 Mantis 7250 Specification sheet mantis/7250-589.pdf 01 Dec 2023 2
4 DeWalt DW870 Instruction manual dewalt/dw870-3OP.pdf 14 Oct 2022 27 2.1 Mb
5 Printronix SL4M Programmer's reference manual printronix/sl4m-SIX.pdf 28 Jul 2023 60
6 Lenovo ThinkCentre A57 Руководство пользователя lenovo/thinkcentre-a57-K5G.pdf 14 Jan 2023 58

Similar Resources:

  • TRASSIR

    TR-D4D2

    (2 pages)
    Indoor IR Network CameraTR-D4D2SpecificationTR-D4D21/3" CMOS 4МP4MP(2560x1440)4MP@25fps1/2 ~ 1/1 000 sMechanical ICR0.003Lux (F1.3)up to 25 m2.7 - 13.593˚ - 28˚ / 50˚ - 16˚D-WDR (105 dB)3D DNRН.265+ / Н.265 / H.264up to 8MbpsYesYesPoE (802.3af) / 12V DC4DC: 4WPoE: 4.6WPlasticØ112 x 98.1250 / 350TVS 4000V-10°C … +50°CModelImage sensorResolut …
  • Xiaomi

    Mi 360

    (169 pages)
    Mi 360° Home Security Camera 2K User Manual 1 Mi 360°-Heimsicherheitskamera 2K Benutzerhandbuch 13Manuel d'utilisation de Mi 360° Home Security Camera 2K 25 Manual de usuario de Mi 360° Home Security Camera 2K 37Manuale utente Mi 360° Home Security Camera 2K 49 Руководство пользователя IP …
  • Vicon

    V661D-312N-1

    (28 pages)
    www.vicon-security.com Installation and Operation GuideXX229-11-00V661D-312N-1 Indoor/Outdoor Analog Camera DomeVicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in th …
  • TP-Link

    TL-SC4171G

    (2 pages)
    Warning Before Installation 1MODEL NO. TL-SC4171GPhysical Description 2Package ContentsSystem RequirementQIGResource CDWireless Pan/Tilt Surveillance Camera • Do not keep the Camera exposed to direct sunlight. • Do not place the Camera in high humidity environments such as in a kitchen. • Do not place the Camera where th …
  • American Dynamics

    ADC660N

    (2 pages)
    D A T A S H E E TADC660N and ADC660P1/3-inch Black & White CCD CameraFeatures That Make a Difference: 1/3-inch interline black & white CCD 580 TV lines resolution 0.03 lux low light sensitivity Sensitive to IR illumination Supports DC-type or EE-type auto iris lenses CS lens mount Aperture correction Automatic electronic shutter Automatic gain cont …
  • Lorex

    VANTAGE LNB2151 Series

    (2 pages)
    FOR SUPPORT AND INFORMATION, VISIT WWW.LOREXTECHNOLOGY.COMProduct InformationUser ManualsQuick Start GuidesSpecification SheetsSoftware UpgradesFirmware UpgradesContents• IP Bullet Camera*• Mounting Kit*• 100ft Cat5e Ethernet Cable*Copyright © 2013 Lorex Technologies Inc. As our products are subject to continuous improvement, Lorex reserves t …

Comments, Questions and Opinions: