Manualios.com

EF Cypher 3D Assembly Manual And Setup Manual

  • Cypher 3D Video Game Controller
  • maOkk8nktHKEs
  • Assembly Manual And Setup Manual
  • PDF / Adobe Acrobat Reader
  • 18

EF Cypher 3D Manual Online:

3.4, 1869 votes
EF Cypher 3D User Manual
EF Cypher 3D User Guide
EF Cypher 3D Online Manual

Text of EF Cypher 3D User Guide:

  • EF Cypher 3D, 1 ASSEMBLY MANUAL AND SETUP GUIDE Congratulations - you’ve just bought an electric powered helicopter with a performance that’s going to amaze you! The Cypher 3D is here! This lightweight 3D helicopter has a powerful brushless outrunner motor and matching speed controller and features a 120° CCPM main rotor control system, belt-driven tail rotor, autorotation unit as standard, extensive use of ball races (20 pieces) and much more! Combine this with your choice of lightweight micro servos, gyro, receiver and Li-Po battery (not included) and prepare to be amazed at what this versatile EP helicopter can do! Kit Product

  • EF Cypher 3D, 2 TABLE OF CONTENTS  

  • EF Cypher 3D, 3 CUSTOMER SERVICE INFORMATION In the USA Global Services 18480 Bandilier Circle Fountain Valley, CA 92708 Phone: (714) 963-0329 Fax: (714) 964-6236 Email: [email protected] Website: http://ef.globalhobby.com  l Li-Po batteries may explode or catch re. Serious injury can result from misuse. l All instructions, warnings and cautions must be followed at all times. Failure to do so can

  • EF Cypher 3D, 4 TOOLS AND SUPPLIES REQUIRED Double-Sided Foam Tape Modelling Knife Needle Nose Pliers Small Phillips Screwdriver Adjustable Wrench  This section describes our recommendations to help you in deciding whic

  • EF Cypher 3D, 5 ❑ The swashplate is controlled by a 120° CCPM system. Choose three identical servos - we are using ballraced Cirrus 302BBs. ❑ Remove the servo horns ❑ Trim the servo horns as shown using a pair of pliers or sidecutters. You need to trim one arm off each of the left/right servo horns and three arms off the fore/aft servo horn as shown. INSTALLING THE CYCLIC SERVOS SERVO INSTALLATION TIPS ● After installing the balls onto the servo horns, apply a drop of thin C/A to the ends of the threa

  • EF Cypher 3D, 6 ❑ Now remove the two forward screws that retain the swashplate anti-rotation link. ❑ The anti-rotation link can now be rocked backwards to clear the swashplate as shown. ❑ The complete shaft assembly can now be withdrawn from the model and put to one side. ❑ Slide the main gear out of the frames. NOTE You do not need to remove the tail drive gear. If you leave it in place it helps ensure that the tail drive belt cannot twist or fall back into the boom. ❑ The fore/aft servo can now be slid under the anti-rotation link and between the main frames. Note the orientation of the servo. ❑ The servo

  • 7 ❑ Screw the servo into its mount using the screws supplied with the servo. Do not use rubber mounting grommets. ❑ Centre the servo, then t the previously prepared servo horn at 90° to vertical and pointing backwards as shown. Tighten the servo horn retaining screw through the access point in the main frame. ❑ This completes the installation of the fore/aft servo and the shaft a

  • EF Cypher 3D, 8 ❑ Re-tighten the grub screw to retain the tail drive gear on the main shaft. ❑ The ball-link from the rear of the swashplate can now be connected to the mounted ball on the fore/aft servo. ❑ Rock the anti-rotation link back into position and replace the two forward screws that were previously removed. ❑ Ensuring the servo is centred, attach the previously prepared servo horn to the left cyclic servo with the mounted ball to the rear and at 90° to the shaft as shown. Tighten the servo horn retaining screw securely. ❑ Slide the servo into its mount. ❑ The ball-link fro

  • EF Cypher 3D, 9 ❑ Screw the servo into its mount using the screws supplied with the servo. Do not use rubber mounting grommets. ❑ The ball-link from the right-hand side of the swashplate can now be connected to the mounted ball on the right cyclic servo. ❑ Prepare the tail servo horn by removing one of the arms as shown. ❑ Attach a mounted ball on the top of the servo horn 10mm out from the centre. ❑ Screw the tail servo into its mount using the screws supplied with the servo. Do not use rubber mounting grommets. ❑ Connect the tail linkage’s ball link to the servo. ❑ Ensure that the pushro

  • EF Cypher 3D, 10  ❑ Cut a length of Velcro (hook and loop material) from the strip supplied. Peel off the backing paper from one side and attach it to the underside of the ESC as shown INSTALLING THE ELECTRONIC SPEED CONTROLLER ❑ Now peel off the backing paper from the second side. ❑ Slide the motor connectors through the sideframes. ❑ Press the ESC into position between the frames as shown. ❑ Connect the three motor wires from th

  • EF Cypher 3D, 11 ❑ Cut two pieces of Velcro (hook and loop material) from the strip supplied. One piece attaches to the top of the receiver and the other is cut to match the angled shape of the sideframes on the rear. ❑ Peel off the backing paper from one side of each piece of Velcro and attach them to the receiver as shown. INSTALLING THE RECEIVER ❑ Remove the remaining backing paper from both pieces of Velcro and slide the receiver into its position to the rear of the main frames under the main gear. NOTE Do not mount the receiver too far forward to ensure that you sti

  • EF Cypher 3D, 12 ❑ Solder on your choice of connectors onto the battery wires from the ESC to suit the Li-Po battery you are using. ❑ We are using an Impulse Li-Po, so have chosen 4mm gold connectors. ❑ The battery ts into the front of the main frames and is retained with a combination of a strip of velcro (hook and loop material) and the velcro strap supplied. ❑ Attach a length of velcro to the top of the battery, remove the backing paper and press the battery rmly in place as shown. ❑

  • EF Cypher 3D, 13 ❑ With the tail rotor servo and servo horn centred, adjust the ball-end so that the tail rotor pivot arm is aligned 90º to the tail boom. INSTALLING THE MAIN ROTOR BLADES AND BODY ❑ Install the main rotor blades, making sure that the rounded leading edge of both blades is facing the same direction as the rounded leading edge of the paddles. IMPORTANT The rotor blades are balanced from the factory. No balancing is required.  INSTALLING THE MAIN ROTOR BLADES IMPORTANT Don't overtighten the socket-cap screws and lock nuts. Tighten

  • 14  ❑ Double-check that the paddles are level when all of the controls are centred. Both paddles should be even with each other, too. Before ying your helicopter for the rst time, it's important to double-check everything once more and to make sure that you've set the helicopter up

  • 15 SPARE PARTS CY0010 Main Frame Sides CY0020 Main Frame Internal Structure CY0030 Belt Guide Pulleys, Front CY0060 Undercarriage Mounting Frames CY0070 Undercarriage Set CY0040 Motor Mount CY0080 Centre Hub CY0090 Flybar Carrier CY0100 Flybar Mixing Arms CY0110 Main Blade Holders CY0120 Feathering Spindle Spacers CY0130 Feathering Spindle CY0140 Paddles CY0150 Flybar CY0170 Mixe

  • EF Cypher 3D, 16 SPARE PARTS CY0010 Main Frame Sides CY0020 Main Frame Internal Structure CY0030 Belt Guide Pulleys, Front CY0040 Motor Mount CY0050 Canopy Mounting Posts CY0060 Undercarriage Mounting Frames CY0080 Centre Hub CY0070 Undercarriage Set CY0090 Flybar Carrier CY0100 Flybar Mixing Arms CY0120 Feathering Spindle Spacers CY0110 Main Blade Holders CY0130 Feathering Spindle CY0140 Paddles CY0160 Flybar Control Arms CY0150 Flybar CY0170 Mixer Block CY0180 Mixer Arm Set CY0200 Anti Rotation Stay CY0190 Swash Plate CY0210 Main Belt Drive Pulley

  • EF Cypher 3D, 17 SPARE PARTS CY0250 Main Shaft CY0570 Main Blades (Wood) - 315mm CY0270 Tail Gearbox Case CY0280 Tail Pitch Lever CY0290 Tail Shaft with Gear CY0300 Tail Control Arm CY0320 Tail Rotor Blade Holders CY0310 Tail Rotor Hub CY0330 Tail Blades CY0340 Tail Servo Mounts CY0360 Horizontal Stabiliser Mount CY0350 Tail Pushrod Guides CY0370 Tail Fin Set CY0380 Tail Boom CY0400 Boom Support Ends CY0390 Tail Boom Supports CY0410 Tail Pushrod Set CY0420 Tail Belt CY0440 Linkage Balls (Long x 6, Short x 2) CY0430 Control Rod Ends (Long x6, Short x2) CY0260 Linkage Set CY0450 Bearings 2 x 5 x 2.5 CY0470 Bearings 4 x 8 x 3 CY0460 Bearings 3 x 6 x 2.5

  • 18 SPARE PARTS CY0480 Bearings 5 x 10 x 4 CY0500 Brushless Motor 3800kv CY0510 Brushless ESC 40A CY0520 Battery Tie CY0530 14T Pinion CY0540 15T Pinion CY0560 Instruction Manual CY0550 16T Pinion CY0580 Canopy with Screen & Decals In North America Your EF Helicopters Cypher 3D is warranted against manufacturer defects in materials and workmanship for a period of 90 days from the date

Related Products and Documents (Video Game Controller):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 LaCie LaCie Ethernet Big Disk Information sheet lacie/lacie-ethernet-big-disk-UN9.pdf 05 Feb 2023 2
2 Pacific hydrostar 37952 Assembly and operating instructions manual pacific-hydrostar/37952-FC7.pdf 25 Mar 2024 9 0.17 Mb
3 Frigidaire FGEF302TNF Wiring diagram frigidaire/fgef302tnf-917.pdf 02 Dec 2022 2
4 AEG B8140-1 Operating instructions manual aeg/b8140-1-F49.pdf 09 Nov 2022 72 1.95 Mb
5 Philips BDM3201F Operation & user’s manual philips/bdm3201f-VTX.pdf 17 Nov 2022 40
6 B&C Speakers Woofer 12 PL 32 Specifications b-c-speakers/woofer-12-pl-32-8G3.pdf 10 Jul 2022 1 0.51 Mb

Similar Resources:

  • Sony

    CUH-1215A

    (2 pages)
    For a wired connection to the Internet, connect a LAN cable (sold separately). Connect the PlayStation®4 system to a TV.Connect the HDMI cable and the AC power cord in order, from to .Getting started Turn on the TV, and then set the TV input to HDMI. Press the (power) button of the PS4™ system to turn the system on.The power indicator blinks in …
  • Hama

    00062868

    (17 pages)
    00062868-08.05Hama GmbH & Co KGPostfach 80 86651 Monheim/GermanyTel. +49 (0)9091/502-0 Fax +49 (0)9091/[email protected] 21.09.2005 9:41 Uhr Seite 2 …
  • Microsoft

    WL3-00018

    (5 pages)
    https://support.xbox.com/en-US/xbox-one/controllers/wireless-controller-solution https://support.xbox.com/en-US/xbox-one/accessories/connect-a-wireless-controller Troubleshoot your Xbox One wireless controller Your Steps 1 Welcome to the Xbox One Wireless Controller Solution Step 1: Welcome to the Xbox One Wireless Controller Solution If you’re having t …
  • LEGO

    Architecture

    (88 pages)
    Flatiron Building New York City, NY, USABookletavailableinEnglishonHeftindeutscherSpracheerhältlichaufLivretdisponibleenfrançaissurFolletodisponibleenespañolenFolhetodisponívelemportuguêsemAfüzetmagyarulezenahonlaponolvashatóLibrettodisponibileinitalianosu2 …
  • ASTRO

    MIXAMP M80

    (2 pages)
    QUICKSTART GUIDEXBOX ONE EDITIONMIXAMP M80VOLUME WHEELFRANÇAISMOLETTE DE VOLUMEESPAÑOLRUEDA DE VOLUMENPORTUGUÊSBOTÃO DE VOLUMEMUTE BUTTONFRANÇAISBOUTON SOURDINEESPAÑOLBOTÓN DE SILENCIOPORTUGUÊSBOTÃO DE SEM SOMLED ARRAYFRANÇAISSÉRIE DE TÉMOINS LUMINEUXESPAÑOLMATRIZ DE LEDPORTUGUÊSMATRIZ DE LEDEQ MODE BUTTONFRANÇAISBOUTON DE MODE ÉGALISEURESPA� …
  • SpeedLink

    DRIFT O.Z.

    (4 pages)
    DRIFT O.Z. RACING WHEEL QUICK INSTALL GUIDEVER.4.0SL-4495-BKOR-V4EL1. Τοποθετήστε το τιμόνι επάνω σε μια λεία επιφάνεια και συνδέστε το με το PS3*. Το κόκκινο LED στο τιμόνι αρχίζει να ανάβει.2. Συνδέστε το κιτ πεντάλ με τη σύνδεση το …

Comments, Questions and Opinions: