DAGE-MTI DC-200 Operation & User’s Manual

Text of DAGE-MTI DC-200 User Guide:

• DAGE-MTI DC-200, Introduction The DAGE-MTI DC-200 is a compact color camera based upon a single 1/3” Interline CCD that provides a high resolution color image. The CCD employs a state of the art microlens design to increase the light gathering capability of the CCD. Digital Signal Processing (DSP) is employed to provide ultimate video enhancement and function. A convenient remote setup keypad is included to utilize the On Screen Display (OSD) commands to set white balance, shutter, gain, back-light compensation, and an eight character camera title. The DC-200 also employs automatic edge enhancement and automatic black

• DAGE-MTI DC-200, Power The red LED located on the camera front lights when power is supplied to the camera. The camera requires approximately 200mA at 12VDC. The external power supply, Dage P/N 738044-02, provides the correct power to the camera. Video The Video BNC connector provides a NTSC (or PAL) composite video signal to be terminated into 75 Ω. For improved video performance, the Y/C video output signal should be used when possible. Y/C The Y/C or sometimes referred to as “S Video” connector provides Y (luminance) and C (color) signa

• DAGE-MTI DC-200, Operation Connect the DC-200 to the OSD Remote and Monitor, then apply Power. Push the MENU button on the remote to activate the On Screen Display Menu, which should be similar to the display shown in figure 2. By pressing the MENU button again, the settings displayed will be stored and menu display will turn off. Figure 2: OSD Menu The active editable menu function will be flashing. Use the UP, DOWN, LEFT, RIGHT buttons to move through menu items and change settings.

• DAGE-MTI DC-200, For example, to change the shutter setting from off to auto: 1. Press MENU. WHITE BALANCE will be flashing. 2. Press DOWN. SHUTTER will be flashing. 3. Press RIGHT. OFF will be flashing. 4. Press UP or DOWN to scroll through the available settings, when AUTO appears, stop. 5. Press MENU to store AUTO and turn off display, or press LEFT then UP or DOWN to edit other menu items in a similar matter. NOTE: When editing MANUAL WHITE BALANCE and CAMERA TITLE, an addi

• DAGE-MTI DC-200, Auto (ATW): This setting places the camera into Auto Tracking White balance mode. In this mode the camera continuously measures the object color temperature and adjusts the white balance automatically. There must be adequate white area in the scene and illumination to perform the white balance. Manual: The Manual White Balance mode allows the user to set the white balance. Adjustment is confirmed with a monitor or vector scope. White balance must be readjusted when light intensity is changed. When using the m

• DAGE-MTI DC-200, Shutter (Electronic Shutter) Off: Camera is set to standard 1/60 (1/50 PAL) second shutter. No excessive light shuttering is performed. Camera gain can be in Auto or Manual (AGC ON or OFF) , but if illumination exceeds the minimum gain of the camera, overload of the video signal results. If viewing high illumination scenes, then set shutter to AUTO or one of the manual settings. Auto: The exposure time is controlled automatically from 1/60 (1/50 PAL) to 1/10,000 second to obtain the video level set. Camera gain can be in Auto or Manual (AGC ON or OFF) . FLCless: (Flicker less) For use in fluorescence illumination w

• Back Light If the scene has too much Back Light (light behind the subject) the AGC (Automatic Gain Control) and Auto Shutter circuits may adjust to the back light instead of the subject. Use the Pattern which provides the best picture. The Back Light function works only when AGC and/or Auto Shutter are on and the illumination level is sufficient for the automatic circuits t

• Focus Adjustment (mechanical back-focus) The Back-Focus is calibrated at the factory and should not need readjustment, however if adjustment is necessary follow the procedure below: 1. Loosen the set screws on the top and bottom of front casting with a 1.5mm hex wrench. 2. Set the lens to maximum aperture and to ∞ focus position. 3. View an object which is 20M

• Specifications: CCD Sensor: 1/3” Interline /w Micro Lenses NTSC: 768x494 Effective Pixels PAL: 752x582 Effective Pixels Sensitivity: 0.015fc, (0.15 lux) /w AGC on Horizontal Resolution: 480 TVL Vertical Resolution: 375 TVL-NTSC / 450 TVL-PAL Signal to Noise: 50dB (AGC off, Y signal) AGC Range: 30dB Digital Processing: 9 Bits Edge E

• DAGE-MTI DC-200, Troubleshooting No Picture (Check or try the following): 1. Camera Power On? a. External Power Supply Attached? b. AC Power On? c. LED on Camera Front On? 2. Monitor Connected to Camera Video Output? a. Monitor Power On? 3. Light Level Too Low? a. Open Camera Lens. b. Set Camera Shutter to Auto or Off. c. Set Camera AGC to On. Picture Saturated (Check or try the following): 1. Video Output Cable Terminated Into 75 Ω ? 2. Light Level Too High? a. Reduce Lens Setting. b. Set Camera Shutter to Auto. c. Set Back-Light Compensation to Off.

• DAGE-MTI DC-200, Warranty The DAGE-MTI DC-200 is warranted to be free of defects in material and workmanship in normal use for a period of one year from the original date of purchase from DAGE-MTI . This warranty does not apply to units which have been subject to abuse, neglect, accident, improper installation, or on which the serial number has been removed or damaged. Units that have been altered without the prior permission of DAGE-MTI are not covered by this warranty. This warranty does not apply to other equipment furnished by DAGE-MTI, which is listed or otherwise identified as manufactured by another and therefo

• DAGE-MTI DC-200, Limitations 1. This warranty is valid only if the malfunctioning unit is returned to DAGE-MTI service depot. This warranty does not cover on-location service. If warranty work is needed, the following should be contacted: DAGE-MTI, INC. Customer Service 701 N. Roeske Ave. Michigan City, IN 46360 (219) 872-5514 Fax: (219) 872-5559 [email protected] 2. This warranty does not cover: a. Problems caused by or inflicted upon associated equipment such as digitizing systems, video tape recorders, cameras, microscopes, etc. b. Damage caused by accident, misuse, improper power source, fire,

Related Products and Documents (Digital Camera):

Comparable Devices:

Similar Resources:

• Oregon Scientific DS9555 (16 pages) Get to know your camera ...................................................................................... 1 Functional parts ..................................................................................................... 1 Explanation of the status icons .............................................................................. 3 Details …

• Elmo L-1EX (68 pages) PART NAMESAND FUNCTIONSSETTING UP STORINGOPERATION PROCEDUREVARIOUS FUNCTIONS AND OPERATIONSTROUBLESHOOTINGSPECIFICATIONSEnglishDocument CameraINSTRUCTION MANUALPlease read this instruction manual carefully before using this product and keep it for future reference. …

• Xenics Bobcat-640-GigE Scientific (24 pages) User Manual Bobcat-640-GigE&CL Camera Company confidential. This document is the property of Xenics. It may not be reproduced – completely or partially – or passed to a third party without written permission from Xenics. Xenics nv T +32 16 38 99 00 Doc Ref: ENG-2012-UMN020 Ambachtenlaan 44 F +32 16 38 99 01 Issue: R000.12 BE-3 …

• SmartWitness CVR600 (4 pages) www.smartwitness.comCVR600 Recording Spy Camera keyfobCVR600 v1.0BEFORE YOU BEGINPlease unpack the box carefully and identify that all the parts are present.Do not attempt to open the casing to access the Camera. Damage caused to the product by tampering with the casing is not covered by the warranty.Do not aim the camera at the sun or similar intense light …

• Sony DSC-TX7 - Cyber-shot Digital Still Camera (219 pages) DSC-TX74-169-511-64(1)ARPR4-169-511-64(1)DSC-TX7© 2010 Sony CorporationPrinted in Japan AR PRGBCTCSMYIDTH© 2010 Sony Corporation4-169-511-64(1)C:\FM\01COV.fmmaster:RightDSC-TX74-169-511-64(1)DSC-TX7GB Digital Still Camera/Instruction ManualCTCSMY Kamera digital/Manual ArahanID Kamera Digital/Panduan PenggunaTH …

• Elmo TT-02S (46 pages) PARTNAMES ANDFUNCTIONSSETTINGUPSTORINGOPERATIONPROCEDUREVARIOUSFUNCTIONS ANDOPERATIONSTROUBLESHOOTINGSPECIFICATIONSEnglishTeacher’s ToolINSTRUCTION MANUALPlease read this instruction manual carefully before using this product and keep it for future reference. …

Comments, Questions and Opinions: