DAGE-MTI CCD-100 Operation & User’s Manual

Text of DAGE-MTI CCD-100 User Guide:

• Introduction The CCD-100 camera system is a fiscally responsible approach to any imaging situation. The camera automatically adjusts to any light situation to provide clear, crisp images for even the most demanding application. In those times when control is a necessity, the camera's automatics can be switched off, allowing control of those parameter

• DAGE-MTI CCD-100, Installation MONITOR CCD100 P/S VIDEO POWER WALL MOUNT ADAPTER Figure 1: CCD-100 Standalone Configuration MONITOR P/S CCD100 RC100 GATE REMOTE REMOTE GATE VID OUT POWER WALL MOUNT ADAPTER Figure 2: CCD-100/RC-100 Configuration MONITOR P/S CCD100 INVESTIGATER REMOTE CAMERA VID OUT POWER TABLE TOP SWITCHING P/S WALL MOUNT ADAPTER RC100 REMOTE GATE WARNING: DO NOT USE WALL MNT ADAPTER NOTE: INVESTIGATER POWER SWITCH CONTROLS CAMERA POWER. RC100 POWER SWITCH IS NON-OPERABLE. WHEN USING INVESTIGATER. (OPTIONAL) Figure 3: CCD-100/Investigater Configuration

• The CCD-100 can function in tandem with the Dage InvestiGater or independently. Figure 1 shows the CCD-100 independently. Attach the power supply to the POWER connector on the CCD-100 . Video output from the VIDEO BNC is available for viewing with a monitor. Figure 2 shows the CCD-100 with the optional RC-100 remote control. The POWER and VIDEO interconnects

• DAGE-MTI CCD-100, Operation Figure 4: CCD-100 Rear Panel POWER The green LED located at the bottom of the rear panel between the GAM switch and the POL switch lights when power is supplied to the camera either through the POWER, GATE, or REMOTE connectors. The camera requires approximately 200mA with a voltage of +10.5VDC to +18VDC. The external power supply, Dage P/N 738044-02, provides the correct power to the camera. VIDEO The BNC video connector provides a 1Vp-p composite video signal into a 75Ω termination. The output video of the camera is also available at the GATE connector. If the GATE connector is being utilized, be sur

• DAGE-MTI CCD-100, GAIN The output level of the camera is determined by the GAIN controls. The gain can be in one of three modes: MAN, AUTO, or AUTO EE . MAN GAIN When the GAIN switch is in the MAN position, the output level of the camera is determined by the rear panel GAIN pot located above the GAIN switch. This pot has a range of about 20db. AUTO GAIN The camera senses the output video level and adjusts the gain to maintain a full level signal when the GAIN switch is in the AUTO position. This position ensures that the camera is providing a nominal output, but it is not

• DAGE-MTI CCD-100, Note: When using the camera in the AUTO EE mode under certain types of lighting such as fluorescent, the camera's output signal may seem as though it is changing in level. This is due to the cyclical nature of the fluorescent light. While the human eye is not capable of viewing the light difference cycle of fluorescent lighting, the shuttered CCD is able to see it. BLACK LEVEL The black level determines the output level of the darkest portions of the image. The BLK switch allows either a manual or automatic mode to set the output video's blacks. MANUAL In the MAN bl

• DAGE-MTI CCD-100, ENHANCE This pot determines the sharpness of the output picture. To sharpen the picture, rotate the pot to the right. In low light situations where the gain of the camera is high, it may be better to not use as much enhancement since it also increases the amount of noise in the output picture. GAMMA Gamma is a non-linear process added to the output video to compensate for the characteristics of a monitor. When GAMMA is ON , the blacks will tend to be stretched in contrast, while the whites will be compressed. If the cam

• DAGE-MTI CCD-100, PIN # FUNCTION REMOTE SET POS 1 Man Gain Pot (+5V=Max; GND=Min) Center 2 Man Black Pot (+5V=Dark; GND=Light) Center 3 Gain Switch (+5V=AUTO; GND=MAN) AUTO 4 AUTO EE (+5V=ON; GND=OFF) 5 Gamma Switch (+5V=ON; GND=OFF) ON 6 Power IN (+12V @ 200mA) 7 Black Switch (+5V=AUTO; GND=MAN) AUTO 8 Enhance Pot (+5V=MAX; GND=MIN) Center Shield GND GATE The gating pulse that the camera uses to inhibit the readout of the CCD is brought in through this connec

• DAGE-MTI CCD-100, CCD for extended periods of time. The external gate pulse is placed on the GATE connector pin as shown in the timing diagram below. The camera has an internal pull-up resistor, so only a ground closure is necessary. Figure 5 shows the exact relationship between CCD readout and composite video. The gate pulse transitions must occur before the CCD transfer for gating or readout to occur. Figure 6 shows the gate pulse relationship to video output. Figure 5: Timing between CCD readout and Video Figure 6: External Gate Timing and Video Readout

• DAGE-MTI CCD-100, Specifications: Sensor: 1/3" IT CCD, 768(H) x 494(V) Resolution: Horizontal: 570 TVL Vertical: 350 TVL Signal to Noise: 57 db Gain Range: >18db Enhancement: 0db to +8db @ 5MHz. Electronic Exposure Range: 1/60 to 1/50,000 sec. Minimum Illumination: 0.007 lux for 20% video out (w/ f/1.2 lens) (No IR Filter) Back Focus Adjustment: ± 1.9mm Lens Mount: "CS" or "C" (with adapter) Input Power: +12VDC @ 200mA Dimensions: 2¼"(W) x 2½"(H) x 5"(L) Weight: 1 lb. Operating Temperature: 0ºC to +40ºC

• DAGE-MTI CCD-100, Troubleshooting No Picture (Check or try the following): 1. Camera Power On? a. External Power Supply Attached? b. AC Power On? c. LED on Camera Rear On? 2. Monitor Connected to Camera Video Output? a. Monitor Power On? 3. Light Level Too Low? a. Open Camera Lens. b. Set Camera into Auto. Picture Saturated: (Check or try the following): 1. Video Output Cable Terminated Into 75 Ω ? 2. Light Level Too High? a. Reduce Lens Setting. b. Set Camera in Auto.

• DAGE-MTI CCD-100, Warranty The DAGE-MTI CCD-100 is warranted to be free of defects in material and workmanship in normal use for a period of one year from the original date of purchase from DAGE-MTI . This warranty does not apply to units which have been subject to abuse, neglect, accident, improper installation, or on which the serial number has been removed or damaged. Units that have been altered without the prior permission of DAGE-MTI are not covered by this warranty. This warranty does not apply to other equipment furnished by DAGE-MTI , which is listed or otherwise identified as manufactured by another and therefore shall be covered by

• DAGE-MTI CCD-100, Limitations 1. This warranty is valid only if the malfunctioning unit is returned to DAGE-MTI service depot. This warranty does not cover on-location service. If warranty work is needed, the following should be contacted: DAGE-MTI, INC. Customer Service 701 N. Roeske Ave. Michigan City, IN 46360 (219) 872-5514 Fax: (219) 872-5559 [email protected] 2. This warranty does not cover: a. Problems caused by or inflicted upon associated equipment such as digitizing systems, video tape recorders, cameras, microscopes, etc. b. Damage caused by accident, misuse, improper power source, fire, flood, lightning, other acts o

Related Products and Documents (Security Camera):

Comparable Devices:

Similar Resources:

• Panasonic WV-SBV131M (200 pages) Operating InstructionsNetwork CameraModel No. WV-SBV131MWV-SBV111MBefore attempting to connect or operate this product, please read these instructionscarefully and save this manual for future use.The model number is abbreviated in some descriptions in this manual. …

• Spyclops SPY-MINIDOMEW (6 pages) SURVEILLANCE SYSTEMS ' SPY~MINIDOMEW ~ CCTV Dome Style Security Camera .t~;l. :.;f -· -_,;_~f._,;,...~~~--......... ,.~ .............. ~... ...., __ .... ~ SPYCLQ)ps~ (~· ~·. .I ( NOTE: Please read this entire Spyclops camera user guide before installation. …

• EverFocus EZ180 (13 pages) HHiigghh RReessoolluuttiioonn BB//WW WWeeaatthheerrpprrooooff CCaammeerraa EEZZ118800User’s Manual and Operation Instructions …

• Genie CCTV GD5324/2.9 (9 pages) Model : GD5324/2.9 GD5324/4 High ResolutionImpact ResistantColour Eyeball Dome CameraInstruction GuideGENIE CCTV LTD.wwwEdition GN-Nov 2012Edition GN-Nov 2012 …

• Dante DNA1425T (124 pages) DNA1425T-DNA1525T Thermal Bullet Cameras Installation and Operations Manual Model Number: DNA1425T, DNA1525T Description: Thermal Bullet Cameras with Intelligent Analytics …

• Spyclops SPY-LPDM4N124 (2 pages) Specification Model SPY-LPDM4N124 Image Sensor 1/2.9" SONY 2.4MP CMOS Sensor Resolution 1080P Signal System PAL / NTSC Minimum Illumination 0.001 Lux/F1.2 S/N Ratio More than 50dB Synchronous System Internal IR Distance 20 Meters (with 12µ x 12PCS Infrared LED) IR Power On Photodiode AUTO Control Video Output AHD/CVI/CVBS/TVI Power/Current DC12V(+/-10 …

Comments, Questions and Opinions: