Manualios.com

ILFOLAB 1250 RC Operating Manual

ILFOLAB 1250 RC Manual Online:

3, 793 votes
ILFOLAB 1250 RC User Manual
ILFOLAB 1250 RC User Guide
ILFOLAB 1250 RC Online Manual

Text of ILFOLAB 1250 RC User Guide:

  • ILFOLAB 1250 RC, 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 SAFETY PRECAUTIONS Your photographic equipment is powered by mains electricity, and is designed to comply with international electrical safety standards. However, basic safety precautions must always be followed when operating electrical equipment, including the following, where applicable: Read and understand all instructions and equipment labels. Close supervision is necessary when the equipment is being used by inexperienced personnel. Take care to avoid burns. Some internal parts of the equipment can become very hot with continuous use. Do not operate equipment that has been dropped or damaged, or has da

  • ILFOLAB 1250 RC, CONTENTS 1 2 2.1 2.2 2.3 2.4 3 3.1 3.2 3.3 3.4 4 5 6 6.1 6.2 6.3 6.4 6.5 7 8 1 PICTOGRAMS 2 INTRODUCTION 5 CONTROLS AND INDICATORS 7 ‘POWER’ light 7 ‘READY’ light 7 Dryer control 7 Speed control 7 INSTALLATION 9 Print receive tray 9 Location 9 Electricity supply 9 Removing yellow transit wedges 9 DRYING PRINTS 10 SWITCHING OFF 11 CLEANING AND SIMPLE REPAIRS 13 Daily routine 13 Cleaning the front roller assembly 13 Replacing a mains fuse 14 Replacing a roller tension spring 14 Removing rear rollers/adjusting print exit guide 15 FAULT FINDING 18 SPECIFICATION 21 INSERTS 94031.2A.GB Wall chart - Operating

  • ILFOLAB 1250 RC, 1 INTRODUCTION 5 See figure 1.1. The ILFOLAB 1250RC variable speed dryer is designed to dry ILFORD black and white resin coated papers to a very high standard. The dryer will dry up to 380 20 . 3x25 . 4cm (8x10 inches) prints per hour, and has a maximum feed width of 50 . 8cm (20 inches). For uniform drying and greater efficiency, prints are dried by infra-red, fan assisted heaters. The print transport speed is variable for precise control of a wide range of drying conditions and materials. This manual gives full instructions for installing and operating the ILFOLAB 1250RC drye

  • 2 CONTROLS AND INDICATORS 2.1 2.2 2.3 2.4 7 See figure 2.1. ‘POWER’ LIGHT The red ‘POWER’ light illuminates when the dryer control is selected to ‘ I ‘ or ‘RUNDOWN’. ‘READY’ LIGHT The orange ‘READY’ light indicates that the machine has warmed up and is ready for use. DRYER CONTROL The dryer control has three positions: Position ‘O’ The dryer is swit

  • ILFOLAB 1250 RC, 3 INSTALLATION 3.1 3.2 3.3 3.4 1 2 3 4 9 See figure 3.1. PRINT RECEIVE TRAY Secure the tray with the screws supplied, as shown in detail B. LOCATION Position the dryer on a firm bench or table at a convenient working height. The dimensions shown in detail A are minimum requirements to allow for adequate air circulation and for the print receive tray. Position the wet-print dish under the dryer. ELECTRICITY SUPPLY Connect the lead supplied to the dryer mains input plug and to a standard wall socket. The lead fits one way only. REMOVING YELLOW TRANSIT WEDGES See figures 3.1 and

  • ILFOLAB 1250 RC, 4 DRYING PRINTS IL887A IL888A IL889 ILFOLAB 1250 RC ILFORD 10 Fill the wet-print dish with enough cold water to cover the washed prints. Switch the electrical supply on. Turn the dryer control to ‘ I ‘. The red ‘POWER’ light illuminates. 1 2 3 Allow about 1 1 / 2 minutes for the orange ‘READY’ light to switch on. During this time, transfer the washed prints to the wet-print dish. As a guide, set the speed control to position 6 to dry resin coated paper sheets. Feed prints emulsion side up. Ensure prints are fed squarely. Feed small prints with the short edge leading. Do not overlap one print with another - allow 2 seconds between the trailing edge of one print a

  • ILFOLAB 1250 RC, 5 SWITCHING OFF IL890A IL891A 11 Turn the dryer control to ‘RUNDOWN’. If the dryer is to be used again later the same day, the control can be left in this position. To switch the dryer off completely, carry out operation 1 and wait for the fans and main drive to stop. Then turn the dryer control to ‘O’. Switch the electrical supply off. 1 2

  • ILFOLAB 1250 RC, 6 CLEANING AND SIMPLE REPAIRS 6.1 1 2 6.2 1 2 3 4 5 13 See figure 6.1. Cleaning is the only regular maintenance required on the ILFOLAB 1250RC dryer. Regular cleaning will ensure correct operation and consistently high drying quality. CAUTION During the following procedures, do not allow water to enter areas of the dryer containing electrical components. Please refer to the Safety Precautions at the front of this manual. DAILY ROUTINE Change the water in the wet-print dish daily or more frequently if necessary. Wipe the outside of the dryer with a damp cloth. CLEANING THE FRONT ROLLER AS

  • ILFOLAB 1250 RC, 6.3 1 2 3 4 6.4 1 2 3 14 REPLACING A MAINS FUSE See figure 6.2. The mains fuse is located to the right of the dryer mains input plug. Switch the electrical supply off. Remove the fuse by turning the fuseholder anti-clockwise with a screwdriver. Replace the fuse with one of the correct value (see section 8). Refit the fuse by turning the fuseholder clockwise with a screwdriver. REPLACING A ROLLER TENSION SPRING See figure 6.3. Roller tension springs are fitted on the four-roller assembly only. Springs are fitted to both ends of the roller pairs, as shown. Switch the electrical supply off.

  • ILFOLAB 1250 RC, 4 5 6 7 8 9 6.5 15 To remove a tension spring left hand side, release the socket set screws and remove the gears and locating plate, as shown on Detail A. Unhook and remove the spring from the end of the roller pair. Fit a new spring around the roller bearings, as shown. Refit the locating plate and gear. Secure each gear by tightening the socket set screw against the flat on the roller shaft. To remove a tension spring right hand side as shown on Detail B, carry out operations 5 and 6. Refit the roller assembly and close the dryer. REMOVING REAR ROLLERS/ADJUSTING PRINT EXIT GUIDE See figure 6.1. The gap between the print exit guide and t

  • ILFOLAB 1250 RC, 1 2 3 4 5 6 1 2 3 4 5 6 16 To remove the rear rollers, proceed as follows: CAUTION This operation requires access to the electrical compartment. Please refer to the Safety Precautions at the front of this manual. Switch the electrical supply off. Press the release button and open the dryer until the lid is held securely by the restraining arm. Release the four screws and remove the lower cover. Carefully remove the upper roller, complete with bearings. Carry out the following operations only if the lower roller is to be removed. Slacken the

  • ILFOLAB 1250 RC, 7 8 17 Switch the electrical supply on. When the dryer is ready, feed a number of wet sheets through, ensuring they exit the dryer without obstruction. If the sheets do not exit correctly, switch the electrical supply off and check the alignment of the print exit guide. Re-adjust the guide if necessary.

  • ILFOLAB 1250 RC, 7 FAULT FINDING 18 Sheet fed upside down Feed sheets emulsion side up Prints pulled from the exit Leave prints to emerge fully rollers from the dryer before handling them Dirty paper guides Remove roller assemblies and inspect guides. See figure 3.1. Clean guides as necessary Dirty feed tray Clean feed tray. See figure 3.1 Paper guides bent Contact your local ILFORD Selling Company Dryer speed too high Adjust speed control to a slower setting Faulty heater element Contact your local ILFORD Selling Company Rollers operati

  • ILFOLAB 1250 RC, 19 Dryer speed too high Adjust speed control to a slower setting Prints not fully wetted before Ensure prints are completely drying immersed in the wet-print dish before drying Dryer speed too low Adjust speed control to a faster setting Dryer fan impeded Remove any obstruction from dryer air grille. Observe installation procedure. See section 3.2 Dryer speed too low Adjust speed control to a faster setting Dryer speed too low Adjust speed control to a faster setting Dirty front roller ass

  • ILFOLAB 1250 RC, 20 Paper sheet too small Switch dryer off. Retrieve sheet. Sheets must be at least 5 inches (12 . 7cm) long Damaged sheet Switch dryer off. Retrieve sheet Rollers operating incorrectly Switch dryer off. Retrieve sheet. See symptom 2 Paper guides bent Switch dryer off. Retrieve sheet. Contact your local ILFORD Selling Company Exit guide misaligned Check alignment of exit guide. Adjust if necessary. See section 6.5 Symptom Possible cause Remedy Print fails to emerge 9

  • ILFOLAB 1250 RC, 8 SPECIFICATION 21 PERFORMANCE DATA Control switch selected to ‘ I ’ Minimum speed setting : 17.5cm/min (7 inches/min) Maximum speed setting : 126cm/min (49.6 inches/min) 380 20.3x25.4cm (8x10 inches) prints per hour at speed setting 12 and the control switch selected to ‘ I ‘ 70 seconds Typically 25 seconds for a 20 . 3x25 . 4cm (8x10 inches) print with the speed setting at position 6 and the control switch selected to ‘ I ‘ PRINT SIZES ACCEPTED 50 . 8cm (20 inches) 12 . 7cm (5 inches) DRYER DIMENSIONS 273mm (10 . 9 inches) 755mm (29 . 7 inches) 615mm (24 . 2 inches) including print receive tray WEIGH

  • ILFOLAB 1250 RC, DECLARATION OF CONFORMITY ILFORD ILFORD DECLARE UNDER OUR SOLE RESPONSIBILITY THAT PRODUCT ILFOLAB 1250RC dryer NAME . TYPE OR MODEL TO WHICH THIS DECLARATION RELATES IS IN CONFORMITY WITH THE FOLLOWING SPECIFICATIONS SPECIFICATION NUMBER EC DIRECTIVE Electromagnetic compatibility - emissions EN50081-1:1990 89/336/EEC Electromagnetic compatibility - immunity EN50082-1:1990 89/336/EEC Safety of information technology equipment EN60950:1988 73/23/EEC including electrical business equipment CATEGORY Domestic, commercial and light industry NAME OF AUTHORISED OFFICER POSITION OF AUT

  • ILFOLAB 1250 RC, Australia ILFORD Imaging Asia Pty Limited Monash Corporate Centre Unit 1/10 Duerdin Street Clayton North 3168 Victoria Benelux ILFORD Imaging Benelux Fotografielaan, 18 2610 Wilrijk Belgium Canada ILFORD Imaging Canada Limited 361 Steelcase Road West Unit No.4 Markham Ontario L3R 3V8 France ILFORD Imaging France SA 10 Allee des Ginkgos 69673 Bron - Cedex Germany/Austria ILFORD Imaging GmbH Heinrich-Hertz-Str 1 POB 10 11 68 D-63265 Dreieich Italy ILFORD Imaging Italia SpA Corso Italia 13 21047 Saronno (VA) Switzerland ILFORD Imaging Switzerland GmbH Route de l’Ancienne Papeterie Case Postale 160 CH-1723 Marly 1 United Kingdom ILFORD Imaging UK Limited Town Lane Mobberl

Related Products and Documents (Printer):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 HIKVISION DS-2CC5197P-DG1 Operation & user’s manual hikvision/ds-2cc5197p-dg1-I48.pdf 04 Jul 2023 45 1.07 Mb
2 Husqvarna LC153S Illustrated parts list husqvarna/lc153s-RV8.pdf 13 Apr 2023 5
3 AVer EH6108H Quick user manual aver/eh6108h-221.pdf 31 Dec 2023 21
4 Frigidaire Oven circuit Wiring diagram frigidaire/oven-circuit-2O1.pdf 19 Jan 2024 1 0.06 Mb
5 GE DPGT750EC/GC Technical service manual ge/dpgt750ec-gc-22H.pdf 12 Sep 2022 63 2.79 Mb
6 Sony BDV-IT1000ES Connection manual sony/bdv-it1000es-2Y2.pdf 13 Mar 2023 2 0.9 Mb

Similar Resources:

  • Canon

    PIXMA iX6520

    (28 pages)
    seriesESPAÑOLENGLISHAsegúrese de leer este manual antes de utilizar la impresora. Consérvelo a mano para utilizarlo como referencia en el futuro.Guía de inicioImpresora de inyección de tinta para empresas CanonLéame en primer lugarMake sure to read this manual before using the printer. Please keep it in hand for future reference.Getting StartedCanon In …
  • Mitsubishi Electric

    CP-W5000DW

    (31 pages)
    DIGITAL COLOR PRINTERMODELCP-W5000DWOPERATION MANUALTHIS OPERATION MANUAL IS IMPORTANT TO YOU.PLEASE READ IT BEFORE USING YOUR DIGITAL COLOR PRINTER.Hereby, Mitsubishi Electric Corporation, declares that this digital color printer is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. …
  • Brother

    HL-2140

    (1 pages)
    Quick Setup Guide - Brother HL-2140 - 1. Access to the following URL http://www.brother-usa.com/Support/ 2. Select “Printers (HL series)” in the Select Product Group of More Support Options. 3. Select "HL-2140” in Select Model and Click “View” button. 4. Click "HL-2140 Downloads on our Online Solution Center" link in …
  • Mitsubishi Electric

    CP-D70DW

    (93 pages)
    2010CAUTIONBefore servicing this chassis, it is important that the service person reads the “SAFETY PRECAUTIONS” and “PRODUCT SAFETY NOTICE” in this service manual.Copyright © 2010 Mitsubishi Electric Corporation All Rights Reserved.MODELCP-D70DWThis model is RoHS-compliant. Provide servicing referring to “NOTES FOR SERVICING RoHS-COMPLIANT PRODUC …
  • Xerox

    VersaLink C405

    (50 pages)
    Xerox® VersaLink® C405/B405 Multifunction Printer Security Function Supplementary Guide Document Version 1.0: March 2018 …
  • Avery Dennison

    Monarch Pathfinder Ultra Silver

    (26 pages)
    Fixed FormatsUser ManualFixed FormatsUser Manual32232SALE$25.005852349978965234151MENS SHIRTSMALL$26.33MonarchPathfinder UltraPrinter®®®SilverTC6032FFUM Rev. AE 3/08 ©2006 Paxar Americas, Inc. a subsidiary of Avery Dennison Corp.All rights reserved. …

Comments, Questions and Opinions: