Manualios.com

Dataplex DPX-213 Operation & User’s Manual

Dataplex DPX-213 Manual Online:

3.85, 1853 votes
Dataplex DPX-213 User Manual
Dataplex DPX-213 User Guide
Dataplex DPX-213 Online Manual

Text of Dataplex DPX-213 User Guide:

  • Dataplex DPX-213, INSTALLATION Section 2 2-2 Copyright (C) Dataplex Pty Ltd U1 RESET Figure 2.2 DPX-213 Jumper Locations J4: Removing this jumper reduces current consumption by disabling the front panel LEDs. J5: Removing this jumper stops the V.24 DTR input which controls the standby mode of the DPX-213. Without this jumper set, the unit will not wake up on raise of DTR and will not be held active by the DTR when the unit is placed in standby mode. J8: This jumper enables the sync clocks on the V24 interface. When Pins 1 and 2 are shorted no syn

  • Dataplex DPX-213, BEFORE YOU START Section 3 3-2 Copyright (C) Dataplex Pty Ltd 3.4 Dial-up Line and Leased Line Support The DPX-213 cannot share the same line as your normal telephone. It can only be used in isolation. NOTE: Telephones with Mode 3 connectors should not be used with this equipment. Contact Telecom if you are trying to use the modem on a small business key system such as a Commander, as these hand sets often signal to the PABX electronics with non standard tones and voltages. Damage to either the PABX or the modem could result from incorrect connection. A direct line from the local exchange may

  • Dataplex DPX-213, Section 2 INSTALLATION Copyright (C) Dataplex Pty Ltd 2-5 Table 2.2 Valid Character Formats Start Bit Data Bits Parity Stop Bits Total Bits 1 7 Mark 1 10 1 7 Even 1 10 1 7 Odd 1 10 1 7 Space 1 10 1 8 None 1 10 2.7 Making a Connection Make sure the cable and terminal software are correct, then type atK . This allows the modem to sense the terminal speed and calculate the parity being used. After this has been successfully decoded, the DPX-213 will reply with: "OK" NOTE: If the modem fails to issue the "OK" response, and you are certain the cable, terminal speed and parity are all correct,

  • Dataplex DPX-213, Section 2 INSTALLATION Copyright (C) Dataplex Pty Ltd 2-7 The called modem will turn on the ring indicator with each incoming ring (Pin 22). It will usually output the word "RING" to the terminal with each incoming ring unless this feature has been disabled with the ATQ or ATV commands. The DPX-213 can be configured so it will: • Answer at a particular ring count (typically, the answering modem will be set to answer on the first or second ring; • Never answer; • Answer if the data terminal ready lead (Pin 20) is asserted. 2.10 Trouble Shooting If you are sure

  • Dataplex DPX-213, APPLICATIONS Section 5 5-2 Copyright (C) Dataplex Pty Ltd 5.3 Asynchronous Modes Mode 0 Asynchronous This is the standard default Asynchronous Operating Mode. Enter ATDnnnnnn to dial and go on-line. DTR modes refer only to actions performed on the falling edge. Dialling is performed exclusively by AT dial commands. If AT&D0 is set, answering a call takes place as soon as the ring count in S0 is reached. If DTR is left high, the modem will answer on the number of rings stored in S0, or, as determined by the AT&D1-3 modes. ASYNC MODE DTR RISE DTR FALL DTR LOW AT&M0&

  • Dataplex DPX-213, Document No 113-213-01 Rev 1.0 2008 V CONTENTS APPENDICES Appendix A Problem Report Sheet Appendix B S Register Summary Appendix C ASCII Conversion Table Appendix D Interface Connections Appendix E AT Command Set Summary FIGURES Figure 2.1 Rear Panel Layout 2-1 Figure 2.2 DPX-213 Jumper Locations 2-2 Figure 2.3 Front Panel Layout 2-3 Figure 5.1 Telecom 604 Plug 5-5 Figure 6.1 Flow Control Buffers 6-2 Figure 7.1 Local Analog Loopback 7-2 Figure 7.2 Remote Digital Loopback 7-3 Figure D.1 RJ-11 Connector Wir

  • Dataplex DPX-213, Appendix E AT COMMAND SET SUMMARY Copyright (C) Dataplex Pty Ltd E-2 AT COMMAND SET SUMMARY Command Brief Description Section AT&W Write active configuration to NVRAM 4-22 AT&Z Store phone number to NVRAM 4-22 AT*A Alarm mode. 4-23 AT*C Configuration screen 4-23 AT*D Dumb mode 4-24 AT*E Data compression. 4-24 AT*G Interrupted calling tone. 4-24 AT*P Password security 4-25 AT*R Remote configuration 4-25 AT*Y Break handling 4-25 Dial Modifiers (See ATD comma

  • APPLICATIONS Section 5 5-4 Copyright (C) Dataplex Pty Ltd 5.5 Leased Line Operation The DPX-213 supports leased line operation. This mode (AT&L1) follows the CCITT recommendations for V.22 and V.22bis and is useful for sync and async applications with many manufacturers products. The AT&L1 command does not support Constant Speed Interface or MNP opera

  • Dataplex DPX-213, INDEX J Jack type selection See Connectors Jumper locations/setting 2-2 L Leased line / dial up operation modes 3-2,4-19,5-4 8-5 LED (front panel indicators) 2-3,7-1,7-3 Line feed character 8-3 Lines dial-up leased lines 3-2 3-2,4-19,5-4 Loading default configuration See Configuration Local analogue loopback test 4-21,7-2 Low power mode 5-6 M Make / break ratio 4-20 Manual calling / dialling 3-2 Master reset 2-7 MNP error control data compression delay (autoreliable) 6-4 3-2,4-18,4-21,6-2 to 6-6 4-16 to 4-18,6-4,8-7 8-9 Modem ba

  • Dataplex DPX-213, Section 8 S REGISTERS Copyright (C) Dataplex Pty Ltd 8-1 8.0 S REGISTERS The "S" registers, or status registers store the modem configuration parameters. The S registers (particularly the bit mapped registers) are usually only altered using the AT commands, but in exceptional circumstances may require alteration via the ATSr=n command. S registers should be altered with care, as it is possible to configure the modem with conflicting parameters producing unpredictable results. Should altering the S registers produce erratic operation, reload the factory default settings using the AT

  • Dataplex DPX-213, INSTALLATION Section 2 2-4 Copyright (C) Dataplex Pty Ltd Table 2.1 Front Panel Indicator Names and Functions. Name Function Colour Status TD Transmit Data Yellow Off for mark, On for space, flickering for data RD Receive Data Yellow Off for mark, On for space, flickering for data CD Carrier Detect Green On when CD active, Off when CD inactive. (See AT&C command) OH Off Hook Red On when modem is on line (Off hook). Off when modem is off line (On-hook). When the modem is in Loop modes this LED flashes. 2.5

  • Section 4 AT COMMAND SET Copyright (C) Dataplex Pty Ltd 4-17 AT&H HELP Parameters : 0 to 4 Default : None This command displays several levels of help screens to reduce the need for a handbook to enter field changes. AT&H0 - General help Summary. AT&H1 - Extended help Summary. AT&H2 - Help on Dial Modifiers. AT&H3 - Help

  • Section 8 S REGISTERS Copyright (C) Dataplex Pty Ltd 8-7 S30 MNP, CSI, Result Codes, Pulse Ratio, Character Size Default : BC Hex Range : 0 to 255 (Stored in NVRAM) BIT VALUE(S) AT COMMAND DESCRIPTION 0 0 1 AT&E0 AT&E1 MNP 2-4 error control disabled. MNP 2-4 error control enabled. 1 0 1 AT*E0 AT*E1 MNP 2-5 compression disab

  • Dataplex DPX-213, Section 4 AT COMMAND SET Copyright (C) Dataplex Pty Ltd 4-7 A/ Repeat Last Command Parameters : None Default : None A/ is the only command that must not be preceded by an "AT" or terminated with a carriage return ( K ). This command will repeat the preceding command string. This is useful for redialling a previously engaged phone number. ATA ANSWER Parameters : None Default : None Causes the modem to answer an incoming call (go off-hook), try to train on the incoming signal and then go on-line. There will be a 2.1 second delay to pass STD beeps, billing meter pulses and the modem's answer

  • Dataplex DPX-213, Section 10 WARRANTY and REPAIRS Copyright (C) Dataplex Pty Ltd 10-1 10.0 WARRANTY AND REPAIRS Dataplex warrants the DPX-213 to be free from defective materials or workmanship for a period of 3 months from the date of purchase. This warranty is extended to 12 months from date of purchase for users who return the warranty registration card within 30 days from the date of purchase. This warranty does cover equipment damaged by accident, abuse, unauthorised modifications, or improper use.

  • TECHNICAL SPECIFICATIONS Section 9 9-2 Copyright (C) Dataplex Pty Ltd Environmental Temperature 0 to 85 degrees C. Relative humidity < 95%, non-condensing. Physical Height - 20 mm. Width - 127.8 mm. Depth - 130 mm. Weight - 0.6 kg. MODELS AVAILABLE DPX-213-01 240VAC Standard Mains Operation DPX-213-02 7-20VDC Standard DC Operation

  • Dataplex DPX-213, Section 8 S REGISTERS Copyright (C) Dataplex Pty Ltd 8-9 S50 Redial Attempts Default : 5 Decimal Range : 0 to 256 Seconds (Stored in NVRAM) If a call is made in AT*A mode and the message is not successfully sent, the unit will attempt to redial the number of times stored in this register before giving up. This takes into account alternate number dialling. In this scenario, the modem attempts to connect using the number stored in location 0 and then the number stored in location 1 on failure to send an alarm message. For example, if alternate numbers are provided and S50 is set to four then both numbers will be dialed fou

  • Dataplex DPX-213, Appendix C ASCII CONVERSION TABLE Copyright (C) Dataplex Pty Ltd C-2 ASCII CONVERSION TABLE 128 10000000 144 10010000 160 10100000 176 10110000 192 11000000 208 11010000 224 11100000 240 11110000 80 90 A0 B0 C0 D0 E0 F0 129 10000001 145 10010001 161 10100001 177 10110001 193 11000001 209 11010001 225 11100001 241 11110001 81 91 A1 B1 C1 D1 E1 F1 130 10000010 146 10010010 162 10

  • Dataplex DPX-213, AT COMMAND SET Section 4 4-4 Copyright (C) Dataplex Pty Ltd 1. Idle State This state is entered shortly after power is applied to the modem and the power-up self test has been passed. It can also be entered after the modem has executed a non- dialling command line. In this state, the modem is waiting to autobaud an AT sequence from the DTE or awaiting a ringing signal from the telephone line. If a valid 'AT' entry is detected, the modem enters the Command State. If a valid ringing signal is detected the modem will send a RING message to the DTE at the last autobaud speed. If set to answer (S-Register

  • Dataplex DPX-213, AT COMMAND SET SUMMARY Appendix E E-1 Copyright (C) Dataplex Pty Ltd AT COMMAND SET SUMMARY Command Brief Description Section A/ Repeat command - NO AT prefix 4-7 ATA Answer 4-7 ATB Bell/CCITT select 4-7 ATD Dial command 4-8 ATDn Dial stored number 4-9 ATE Echo command 4-9 ATF Communication format/force line speed 4-10 ATH Hook command - hang up 4-10 ATI Identify modem 4-10 ATNn&Z Store string in location n 4-11 ATO On line, originate and retrain 4-11 ATP Pulse dial modifier 4-12 ATQ Result code & quiet mode 4-12 ATSr? S register inquire 4-12 ATS=n S register set command 4-13 ATT Tone dial modifier

  • Dataplex DPX-213, Section 2 INSTALLATION Copyright (C) Dataplex Pty Ltd 2-1 2.0 INSTALLATION Read this Section in order to correctly install your modem. It includes information on connector pinouts, front and rear panel details and a simple test of your setup. Before operation is possible, the modem must be setup, either to the factory defaults or with special S-register values to suit your own configuration. Most communications software packages issue a default command string to set up the modem. Before altering this default setup, chec

  • Dataplex DPX-213, AT COMMAND SET Section 4 4-18 Copyright (C) Dataplex Pty Ltd AT&K DTE Flow Control Parameters : 0 to 3 Default : 1 (Select Xon/Xoff Flow Control) This command selects the method of handshaking between the DTE and the modem during error correction, data compression or whenever the Constant Speed Interface is set at a different rate to the line speed. NOTE: Xon/Xoff flow control should NOT be used when passing binary, command or executable files since they may contain Xoff characters withou

  • Dataplex DPX-213, AT COMMAND SET Section 4 4-22 Copyright (C) Dataplex Pty Ltd Pass through means that, if Xon/Xoff flow control is enabled, the controlling character detected will be acted upon by any buffer it encounters, and then passed through to the next buffer in the link. Disabling pass through means that any Xoff character received by a buffer will be obeyed but the Xoff character will then be discarded. If line flow control is enabled, the receiving modem line buffers will be susceptible

  • Dataplex DPX-213, AT COMMAND SET Section 4 4-24 Copyright (C) Dataplex Pty Ltd AT*D DUMB Mode Parameters : 0 to 3 Default : 0 (Disabled) To prevent modem "lock up", it is advised that the escape sequence 'pause' +++ 'pause' be disabled when using the Dumb Mode (see Register S2 description for more details). AT*D0 - Allows the DPX-213 to respond to normal AT command and attention sequences. AT*D1 - Disables AT command acceptance and echo. Once the modem is configured, AT co

  • Dataplex DPX-213, AT COMMAND SET Section 4 4-2 Copyright (C) Dataplex Pty Ltd 3. Entering ats7=60K will cause the modem to wait 60 seconds for carrier from the answering modem. 4. Entering atdn5K will cause the modem to dial the number stored in location 5. Or type one concatenated string: atx3 s0=4 s7=60 dn5 K which has the same effect (spaces between commands are ignored and are optional). The above command descriptions have numeric modifiers to allow selection from one of several command options. These are usually shown as parameters 0 to 9. Where a numeric selection is omitted, the command processor assumes a zero (0) has been entered.

Related Products and Documents (Modem):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 AEG AT 143 U Operating instructions manual aeg/at-143-u-255.pdf 22 Mar 2024 36 0.32 Mb
2 Sharp MD-MT20H Operation manual sharp/md-mt20h-747.pdf 29 Feb 2024 44 1.88 Mb
3 MicroFridge 2.9MF-7TP Manual  microfridge/2-9mf-7tp-VRW.pdf 17 Feb 2023 2
4 Epson EMP EMP-1825 Operation & user’s manual epson/emp-emp-1825-CZE.pdf 13 Mar 2023 111 6.79 Mb
5 Compaq 2025 Operation & user’s manual compaq/2025-2IT.pdf 04 Jan 2023 36 1.75 Mb
6 Samsung SDC-313B Operation & user’s manual samsung/sdc-313b-7AI.pdf 22 Sep 2023 21 4.57 Mb

Similar Resources:

  • T-COM

    Speedport W 100

    (26 pages)
    109.01.2007 KA_D_154_stick.fmSpeedport W 100 Stick InstallationsanleitungBeachten Sie unbedingt auch die Sicherheitshinweise für den Umgang mit diesem Produkt, wie sie in der Bedienungsanleitung auf der CD-ROM des Lieferumfangs aufgeführt sind. Eine Haf-tung von T-Com für Schäden aus nicht bestimmungsgemäßem Gebrauch oder unsachgemäßer Handhabung des …
  • Robustel

    GoRugged M1000 XP

    (63 pages)
    Robustel GoRugged M1000 XP Industrial Serial to Cellular Gateway For GSM/GPRS/UMTS Networks User Guide Document Name: User Guide Firmware: 1.01.00 M1000 XP Configurator: 1.01.00 Date: 2016-11-16 Status: Confidential Doc ID: RT_UG_M1000 XP_v.1.1.3 …
  • 3Com

    3C871

    (15 pages)
    ® 3C OM I MPACT ISDN E XTERNAL D IGITAL M ODEM Q UICK S TART I NSTRUCTIONS Part Number 09-0700-002The following information will help you install the 3Com  Impact  ISDN External digital modem models 3C871, 3C872, 3C876, or 3C877. Refer to the 3Com Impact ISDN External Digital Modem User Guide for additional information. Site Preparation T …
  • Black Box

    RM1600

    (2 pages)
    1®© Copyright 1998. All rights reserved.Black Box Corporation.®BLACK BOXThe World’s Source for ConnectivitySMSave money, workspace,and time by centralizing yourdata-communicationsequipment.LED status indicators foreach card show errorconnection, connect rate,and connection speed.Cards support data ratesup to 33.6 kbps over dial-uplines and 2- or 4-wire …
  • Telstra

    MF910V

    (31 pages)
    Page 1 of 31 TELSTRA 4GX WI-FI (MF910V) USER MANUAL Copyright © 2016. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by Z …
  • Victron energy

    GX LTE 4G Series

    (9 pages)
    2020-08-01 15:42 1/9 GX LTE 4G - ManualVictron Energy - https://www.victronenergy.com/live/GX LTE 4G - ManualNOTE: DRAFT MANUAL. FIRST STOCK EXPECTED IN 2020 Q41. Introduction1.1 Product descriptionThe GX LTE is an accessory for GX-devices. It is a cellular 2G, 3G and 4G modem; providing a mobileinternet for the system and connection to Victron Remote Manage …

Comments, Questions and Opinions: