ACTi B41 Manual Manual

Text of ACTi B41 User Guide:

• ACTi B41, www.acti.com Hardware Manual 4 Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment. Servicing Do not attempt to service this video device yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Trademarks All names used in this manual are probably registered trademark

• ACTi B41, www.acti.com Hardware Manual 32 How to Use the Male Conduit Gland This section describes how to waterproof the cable(s) using the bundled male conduit gland and flexible conduit. This is the recommended solution if other devices, such as an audio or digital input/output device will be connected to the camera or when the use of a power adapter is necessary. All the device cables including the power adapter and Ethernet cable can be housed inside the flex conduit. The camera may or may

• ACTi B41, www.acti.com Hardware Manual 13 Installation Procedures This section describes the procedures in installing the camera on the wall using the integrated bracket. IMPORTANT! Before installation, make sure the wall can bear more than the weight of the camera and its bracket. NOTE: The following procedures and pictures are based on the cable going along the wall; same procedures apply when the cable will pass through the wall, unless otherwise specified. Step 1: Prepare for Installation 1. Depending on the wall material, purchase applicable screws and screws plugs (as needed) that can hold the camera and brac

• ACTi B41, www.acti.com Hardware Manual 37 3. Connect the wire with the white stripe to the 12V pin and the other to the GND pin. 4. Tighten the screws of the 12V pin and the GND pins to secure the wire connection. 5. Set the prepared power adapter for connection later. Below is an example of a power adapter with an attached terminal block. NOTE: The power adapter is not bundled in the package.

• ACTi B41, www.acti.com Hardware Manual 16 Step 5: Connect to Network Connect the other end of the network cable to a switch or injector. Then, connect the switch or injector to a network or PC and a power source. See Power-over-Ethernet (PoE) example connection diagram below. Network AC Power Source PoE Injector / PoE Switch Power Cable Ethernet Cable Ethernet Cable (Data + Power) Ethernet Cable (Data) Camera In case of using a non-PoE switch, po

• ACTi B41, www.acti.com Hardware Manual 24 6. On the “pigtail” side, insert the washer into the “pigtail”. 7. Connect the Ethernet cable connector to the “pigtail” connector. 8. Attach the gland body to the “pigtail”. NOTE: Make sure the gland body is tightly attached to the “pigtail” and the washer is secured between them.

• ACTi B41, www.acti.com Hardware Manual 33 2. Attach the gland body to the hole of the cover. 3. Pull enough length of the device cables without connectors through the flex conduit. The terminal blocks will be attached once the cable passes through the gland body and cover later. 4. Insert the clamping nut through the flex conduit.

• www.acti.com Hardware Manual 26 Waterproof Solution Using the Camera Connectors For more flexible applications, use the connectors at the back of the camera to connect a power adapter or other devices. Or in some cases, users may require the use of specific cables with customized length. In such cases, use one of the following solutions:

• ACTi B41, www.acti.com Hardware Manual 20 2. Insert the clamping nut into the Ethernet cable. 3. Insert the sealing insert with claw. 4. Insert the gland body into the Ethernet cable. 5. On the “pigtail” side, insert the washer into the “pigtail”.

• www.acti.com Hardware Manual 10 Physical Description Exterior View Connectors View NOTE: The connectors are hidden under the housing cover. 1) Ethernet Ports The Ethernet port (1a) of the cable-out or “pigtail” connects to a network using an Ethernet cable. The Ethernet port (1b) on the housing connects the cable-out or “pigtail” t

• ACTi B41, www.acti.com Hardware Manual 15 Step 3: Install the Camera 1. If the “pigtail” will pass through the wall, follow Waterproof Solution Using the “Pigtail” on page 18 first and then route the cable through the wall. If the “pigtail” will go along the wall, route the cable through one of the cable gaps on the bracket. 2. Install the camera to the wall using four (4) screws applicable for the wall material (purchased separately). NOTE: Make sure the wall can bear more than

• ACTi B41, www.acti.com Hardware Manual 17 Step 7: Adjust the Viewing Angle Based on the camera live view, adjust the camera viewing angle. Do the following: Using the bundled bracket wrench, do the following: 1. Loosen the tilt adjustment screws, adjust the camera tilt, and then tighten back the screws to fix the tilt position. 2. Loosen the pan adjustment screw, move the pan direction, and then tighten back the screw to fix the pan position. Pan Adjustment Screw Tilt Adjustment Screw

• ACTi B41, www.acti.com Hardware Manual 51 Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web browser and typing the following address into Web browser’s address bar: http://192.168.0.100 Upon successful connection to the camera, the user interface called Web Configurator would appear together with the login page. The HTTP port number was not added behind the IP address since the default HTTP port of the camera is 80, which can be omitted from the address f

• ACTi B41, www.acti.com Hardware Manual 34 5. Insert the sealing insert and attach it at the end of the flex conduit. 6. Pull the device cables through the gland body. 7. Attach the terminal blocks, see Other Connections on page 36 for more information. 8. Connect the cables to the corresponding connectors on the camera.

• ACTi B41, www.acti.com Hardware Manual 2 Table of Contents Precautions ............................................................. 4 Safety Instructions .................................................................................... 6 Introduction ............................................................. 7 The List of Models ..................................................................................... 7 Package Contents ...................................................................................... 8 Physical

• ACTi B41, www.acti.com Hardware Manual 45 How to Insert a Memory Card The camera supports local video recording or saving of snapshots to a memory card. NOTE: Supports microSDHC and microSDXC cards. How to Insert the Memory Card 1. Open the back cover of the camera. 2. Insert a memory card into the card slot with the metallic contacts facing down. Push the card until it clicks into place. How to Remove the Memory Card In case there is a need to remove the card, make sure to access the camera Web Configurator to safely “unmount” the card first (see the camera Firmware manual for more information). On

• www.acti.com Hardware Manual 42 Other Adjustments and Accessories How to Remove the “Pigtail” For applications that may require the use of the Ethernet port at the back of the camera, remove the “pigtail” from the camera. Follow the procedures below: 1. Loosen the four (4) screws to remove the back cover of the camera. 2

• ACTi B41, www.acti.com Hardware Manual 25 9. Push the flex conduit and insert the sealing nut into the gland body. NOTE: Make sure the clamping nut is tightly attached to the cable gland body and the sealing insert is squeezed tightly. 10. Attach the clamping nut to complete the cable solution.

• ACTi B41, www.acti.com Hardware Manual 36 Other Connections This section describes the procedures in preparing the external devices that you can connect to the camera. The camera supports DC12V power input, Digital Input and Output (DI/DO) and Audio Input and Output devices using the bundled terminal blocks. The use of these devices, however, is optional. Connecting a Power Adapter (Optional) In case of using a non-PoE switch or your PoE switch has limited power supply, you ca

• ACTi B41, www.acti.com Hardware Manual 23 2. Pull the Ethernet cable through the flex conduit. Leave enough length of the cable outside the flex conduit. 3. Insert the clamping nut into through the flex conduit. 4. Insert the sealing nut and fix it at the end of the flex conduit. 5. Insert the gland body into the Ethernet cable.

More Instructions:

	ACTi B41 Hardware manual 27-08-2023 52	DOWNLOAD
	ACTi B41 Installation manual 04-08-2022 30	DOWNLOAD

Related Products and Documents (Security System):

Comparable Devices:

Similar Resources:

• Watchguard WGSIR-500W (4 pages) Watchguard™ Wireless Siren & StrobeInstallation ManualModel: WGSIR-500WProduct Features• Easily connect the wireless transmitter at up to 100m range• Loud siren sound with high-visibility strobe flashes• Dual tamper switch protection for outer casing & wall mount removal• Internal 7.2V rechargeable backup batteryThis wireless outdoor s …

• Eaton i-on series (63 pages) i-on Series Security System Administration and User Manual for i-on Compact, i-on30R+, i-on40H+, i-onG2SM and i-onG3MM Issue 3 Control unit software version 6.00.xx …

• Honeywell Friedland HISK1 (2 pages) ABCDEØ6Ø5No.0No.1No.2Windows PCInternet ExplorerBroadband Router5V 12VGlobalGuard Change PIN code1234PIN code****PIN codedownloadand installGlobalGuardSettingSystemUserRouter - LAN5V2 mingreenglobalguard.friedland.co.ukPC/laptopConfi gure1E21xfollow instructions1x......1x1xfollow instructionsBack doorPatio doorDining roomLiving roomNoneFront doorLocationB …

• Control Products WA-1000 (65 pages) Wireless WaterAlarm User Manual for Wireless WaterAlarm (WA-1000) Thank you for purchasing our Wireless WaterAlarm. This instruction manual covers installation for model WA-1000. General Description The Wireless WaterAlarm automatically calls up to three phone numbers when water is detected by one of the wireless water sensors. It also calls if the powe …

• U-Prox U-Prox Valve (3 pages) www.u-prox.systems/doc_valveENU-Prox Valve - is a wireless device designed to control a valve actuator for water supply, irrigation etc or other external devices.1. U-Prox Valve; 2. Two CR123A batteries (pre-installed); 3. Quick start guideThe device is connected to the control panel and is configured with the U-Prox Installer mobile application.1. Device c …

• Smanos W020 (53 pages) EN NO SE PLPrinted in ChinaPA: W020-UM-EN-NO-SE-PT-V1.0© 2017 SMANOS HOLDING LTD. All Rights Reserved. W020WiFi Alarm SystemMULTILINGUALUSER MANUALMULTILINGUALUSER MANUAL …

Comments, Questions and Opinions: