DCA Intertel s’print BT Operation & User’s Manual
|
DCA Intertel s’print BT, 40DCA Intertel DCA Intertel DCA Intertel 41 DCA Intertel 3. Prining Functions 3.1 CONTROL CHARACTERS The command table lists all the commands for the management of the printer functions. These commands can be transmitted to the printer with the serial interface. The commands can be transmitted to the printer at any moment, but they will only be carried out when the characters previously transmitted have been printed or the commands previously transmitted have been carried out. There are no commands with priority status; all the commands are carried out when the circular buffer is fre
DCA Intertel s’print BT, 14DCA Intertel DCA Intertel DCA Intertel 15 DCA Intertel 1.2.2 Information regarding battery use - Please note that the new NiMH battery reaches maximum performance levels only after having been completely discharged and recharged at least two or three times. - Never use battery rechargers and/or batteries that are damaged or worn. - Battery life varies greatly depending, for example, on print density and the text to be printed. - Recharge times vary depending on depletion levels, type of battery and battery recharger used. Batteries may be recharged and discharged hundreds of
DCA Intertel s’print BT, 6DCA Intertel DCA Intertel DCA Intertel 7 DCA Intertel D. The printer is not functioning normally despite the fact that all instructions in the users manual have been followed. E. The printer has been dropped and its outer casing damaged. F. Printer performance is poor. G. The printer is not functioning. UNPACKING THE PRINTER Remove the printer from its carton being careful not to damage the packing material so that it may be re-used if the printer is to be transported in the future. Make sure that all the components illustrated in gure are present a
DCA Intertel s’print BT, 28DCA Intertel DCA Intertel DCA Intertel 29 DCA Intertel EXAMPLE: To use this protocol to print the text “CUSTOM” in double height and width, send the following data to the printer Start Command Data Stop Command Mode Line Feed 0x1B 0x002 0x03 0x43 0x55 0x53 0x54 0x4F 0x4D 0x0A 0x1B 0x03 C U S T O M NOTE The LED is always switched on (not ashing) when using the infrared port. 2.2.2 InfraRed communication protocol To utilize the IR communication protocol, the “IR Protocol” must rst be set to “Enabled” under setup
20DCA Intertel DCA Intertel DCA Intertel 21 DCA Intertel 1.4 HEXADECIMAL DUMP This function is used to display the characters received from the communications port; after the reception of each 6 characters from the communications port, the printer prints out both the hexadecimal code received as well as the corresponding ASCII code. Shown below is an example of a Hexadecimal Dump: 48
36DCA Intertel DCA Intertel DCA Intertel 37 DCA Intertel 2.4 BLUETOOTH PROTOCOL OVERVIEW (Only mod. DPT100-BT) In the following paragraph there is a brief description of Bluetooth protocol implemented in the printer and differented elements that composed Bluetooth protocol. To Use the Bluetooth communication protocol is necessary that in the set up the parameter “I
42DCA Intertel DCA Intertel DCA Intertel 43 DCA Intertel [Notes] • The commands 00H - 09H do not cancel the print buffer • The commands which modify the direction of the characters are only active at the beginning of the line [Default] Setting in option register by means of front keys [Reference] 00H, 02H, 03H, 04H [Example] 02H [
DCA Intertel s’print BT, 30DCA Intertel DCA Intertel DCA Intertel 31 DCA Intertel 2.2.3 Printing instructions 1) To use the printer’s infrared port, a computer or Personal Digital Assistant (PDA) with IR port is required. 2) Position a computer conforming to the specications in point 2) not more than a meter away from the printer’s infrared port. Make sure the two ports are in front of each other with an angle of not more than 15° on the fou sides. Send the print command from the computer (see g.2.5). 3) Send the following data printing, like descript in to paragraph 2.2.1 and 2.2.2 for mod. DPT100-B or like descript in to paragraph 2.3 for mod. DPT10
DCA Intertel s’print BT, 38DCA Intertel DCA Intertel DCA Intertel 39 DCA Intertel 2.4.1 Supported Protocols The gure 2.10 shows the protocols that are previews in the standard Bluetooth, and the proles that have been implemented in the printer (Object push prole e Serial port prole).
DCA Intertel s’print BT, 6DCA Intertel DCA Intertel DCA Intertel 7 DCA Intertel INTRODUCTION MANUAL ORGANIZATION In addition to the Introduction which includes a description of the explanatory notes used in the manual, general safety information, how to unpack the printer and a brief description of the printer including its basic features, this manual is organized as fol- lows: Chapter 1: Contains the information required for correct printer installation and its proper use, as well as interface specications Chapter 2: Contains information on int
DCA Intertel s’print BT, 14DCA Intertel DCA Intertel DCA Intertel 15 DCA Intertel To replace batteries, proceed as follows: - Remove the cover on the battery compartment (1) by unscrewing the screws (2) and, using a at-head screwdriver, pry open at points A and B (see g.1.5). - Remove the battery pack (2) by lifting the battery removal tape (1) (see g. 1.6).
DCA Intertel s’print BT, 42DCA Intertel DCA Intertel DCA Intertel 43 DCA Intertel 07H [Name] Cancel print data buffer [Format] ASCII - Hex 07 Decimal 7 [Description] Deletes all the print data in the current print buffer. [Notes] • If data that existed in the previously specied printing area also exists in the currently specied printing area, it is deleted. [Default] [Reference] [Example] 0AH [Name] Forward feeds one line [Format] ASCII - Hex 0A Decimal 10 [Description] Forward feeds one line equivalent to a line of print [Notes] • This command
DCA Intertel s’print BT, 10DCA Intertel DCA Intertel DCA Intertel 11 DCA Intertel The red LED displays printer operating status and this check is performed “on-line”. Table 1 lists operating statuses and the LED signals connected to them: LED Status Description Always off Printer off Always on Printer on - no fault with batteries recharing very slow blinking (one blink every three seconds) Printer on - no fault with batteries recharing slow blinking (one blink every second) Paper out message fast blinking (one blink every half second) Resettable error (heat overheating, battery voltage error) Very fast blinking (seven blinks per second) In proces
DCA Intertel s’print BT, 46DCA Intertel DCA Intertel DCA Intertel 47 DCA Intertel ESC # n [Name] Transmit printer ID [Format] ASCII ESC # n Hex 1B 23 n Decimal 27 73 n [Range] 1 d”?n d”?3, 49 d”?n d”?51 [Description] Transmits the printer ID specied by n follows: [Notes] • This command is executed when the data is processed in the data buffer. Therefore, there could be a time lag between command reception and data transmission, depending on data buffer status. [Default] [Reference] [Example] ESC 0 [Name] Turning the printer off [Format] ASCII ESC 0 Hex 1B
DCA Intertel s’print BT, 18DCA Intertel DCA Intertel DCA Intertel 19 DCA Intertel 1.3.2 Conguration Mod. DPT100-BT The printer set up print out (see g. 1.10) includes a range of information, and among these should be pointed out the HEAD VOLT parameter that indicates the battery charge level, i.e., the print head battery voltage. The printer’s congurable parameters, with Bluetooth interface selected, are: • Interface: BTD, RS232. • BT Name ID(14): NO IDD, #0, #1, #2, #3, #4, #5, #6, #7, #8, #9. • Authentication(15): Enabled, DisabledD. • Autofeed: CR disabledD o CR enabled. • Battery:
DCA Intertel s’print BT, 44DCA Intertel DCA Intertel DCA Intertel 45 DCA Intertel ESC (STX) [Name] Enable infrared port [Format] ASCII ESC (STX) Hex 1B 02 Decimal 27 2 [Description] Enable infrared port. [Notes] • if the printer doesn’t receive this command all data sent to infrared port are ignored. • After receiving this command the infrared led is always switched on. [Default] [Reference] ESC (ETX) [Example] ESC (ETX) [Name] Close down the communication with infrared port [Format] ASCII ESC (ETX) Hex 1B 03 Decimal 27 3 [Description] Close down the communication with
DCA Intertel s’print BT, 38DCA Intertel DCA Intertel DCA Intertel 39 DCA Intertel 2.4.1.1 Serial Port Prole The Serial Port Prole provides RS232 serial cable emulation for Bluetooth devices. In this way, legacy applications do not have to be modied to use Bluetooth; they can simply treat a Bluetooth link as a serial cable link. The Serial Port Prole uses RFCOMM to provide serial port emulation. The device which sets up the RFCOMM connection is called the initiator, while the other is referred to responder. A few passages are requested to set the virtual serial port and to establish a connection, so it is necessar
12DCA Intertel DCA Intertel DCA Intertel 13 DCA Intertel 1.1.2 Turning the printer On and Off How to turn the printer On • by briey pressing the multi-function key • by sending a characters set on the serial line—it is better to send characters that are not read as printer controls (ex. 0x0E) • with the battery recharger connected How to turn the printer Off (1) • by briey pre
DCA Intertel s’print BT, 48DCA Intertel DCA Intertel DCA Intertel 49 DCA Intertel [Reference] [Example] ESC c [Name] Management of bar code printing [Format] ASCII ESC c [code] [height] [position] [options] [length] [data] Hex 1B 63 Decimal 27 99 [Description] [ASCII code] Type of bar code I Interleved 2/5 C Code 39 B CodaBar e EAN8 E EAN13 [height] Number of dot lines in 1/8 mm. units. [position] Left hand margin, expressed in 1/8 mm. units [options] bit bit 0 bit 1 bit0: check digit is not printed is printed bit3,2: HR
34DCA Intertel DCA Intertel DCA Intertel 35 DCA Intertel types of frames and is also used to count frames. Frames can carry status, data, or commands. The IrLAP protocol has a command syntax of it’s own, and these commands are part of the control byte. Lastly, IrLAP frames carry data. This data is the information or “I” eld. The integrity of the frame is ensured with a 16-bit CRC, refe
DCA Intertel s’print BT, 2DCA Intertel DCA Intertel DCA Intertel 3 DCA Intertel TABLE OF CONTENS PRINTER COMPONENTS 6 A. DPT100-B – Front external view 6 B. DPT100-B – Under view 7 INTRODUCTION 8 MANUAL ORGANIZATION 8 SYMBOL USED IN THIS MANUAL 8 GENERAL SAFETY INFORMATION 8 UNPACKING THE PRINTER 9 PRINTER FEATURES 10 PRINTER DESCRIPTION 11 1. INSTALLTION AND USE 13 1.1 CONNECTIONS 13 1.1.1 Battery Recharger 13 1.1.2 Turning the printer On and Off 14 1.2 BATTERIES 15 1.2.1 Recharging batteries 15 1.2.2 Information regarding battery use 16 1.2.3 Replacing batteries 16 1.2.4 Disposing of batteries 18 1.3 CONFIGURATION 19 1.3.1 Conguration Mod. DPT10
DCA Intertel s’print BT, 36DCA Intertel DCA Intertel DCA Intertel 37 DCA Intertel 2.3.1.5.3 IAS entry and hint bits An entity advertising 3-Wire raw must set up the IAS entry in one of two forms: • Classname IrDA:IrCOMM with two attributes, called IrDA:IrLMP:LsapSel, and Parameters. The Parameters attribute has at least the service type parameter with at least the 3-Wire raw bit set in it. Optionally IrDA:IrLMP:InstanceName can be used to distinguish between two instances of this service. The Discovery frame must have the IrCOMM hint bit set. It should also have the printer bit set if this is a printing service. • An alternate entry provided for backwards compatibility with some e
DCA Intertel s’print BT, 44DCA Intertel DCA Intertel DCA Intertel 45 DCA Intertel [Default] [Reference] 0FH [Example] 0FH [Name] Set CRLF mode [Format] ASCII - Hex 0F Decimal 15 [Description] Inhibits the command $0D maintaining enabled only the command $0A for printing [Notes] • To disable this option, reset the printer • This command clears the line buffer • On switching on the default value is in the Option Register [Default] Setting in the option register by means of the front keys [Reference] 0DH [Example] 11H [Name] Grap
DCA Intertel s’print BT, 48DCA Intertel DCA Intertel DCA Intertel 49 DCA Intertel ESC Q [Name] Enable underlined printing [Format] ASCII ESC Q Hex 1B 51 Decimal 27 81 [Description] After this command has been received, the characters are printed underlined [Note] [Default] [Reference] ESC q [Example] ESC R [Name] Set reverse mode printing [Format] ASCII ESC R Hex 1B 52 Decimal 27 82 [Description] Selects printing in reverse mode: the receipt feeds out of the printer with the printing in no
Kyocera KM-3050 Printer Operation manual
KM-3050 |
Epson 7880 - Stylus Pro Color Inkjet Printer Printer Brochure & specs
7880 - Stylus Pro Color Inkjet Printer |
HP D5460 PhotoSmart Inkjet Printer Start here
D5460 PhotoSmart Inkjet |
Brother MFC-9330CDW Printer Specfications
MFC-9330CDW |
UBI EasyCoder 101 Printer Operation & user’s manual
EasyCoder 101 |
Lexmark All in One Printer Printer Operation & user’s manual
All in One Printer |
Panasonic UF-4100 Printer Specifications
UF-4100 |
Xerox 8200DX - Phaser Color Solid Ink Printer Printer Manual
8200DX - Phaser Color Solid Ink Printer |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Clarinet Systems | ES608 | Manual | clarinet-systems/es608-P5F.pdf | 31 Jan 2024 | 13 | 0.14 Mb |
2 | Zanussi | 726141 | Specifications | zanussi/726141-23V.pdf | 14 Jun 2023 | 4 | 0.18 Mb |
3 | AOpen | DX37-U | Installation manual | aopen/dx37-u-8XJ.pdf | 19 Jun 2023 | 8 | 0.89 Mb |
4 | Kambrook | KT110 | Instruction booklet | kambrook/kt110-EQ8.pdf | 26 Nov 2022 | 12 | |
5 | MB QUART | Discus DUA 210 | Installation manual | mb-quart/discus-dua-210-Z81.pdf | 04 Apr 2023 | 4 | |
6 | GE | ASM14AL | Owner's manual and installation instructions | ge/asm14al-XNL.pdf | 22 Jul 2023 | 40 | 1.26 Mb |
Kyocera
First edition 2008.11Printed in China 303ML56020DF-650(B)/MT-1(B)/BF-1(B)/PH-4(A)/PH-4(C)Operation GuideManuel d'utilisationGuía de usoEinführungGuida alle funzioni620/820DF-650(B)/MT-1(B)/BF-1(B)/PH-4(A)/PH-4(C)
…
TASKalfa 620(176 pages) |
Samsung
Color Laser PrinterCLP-315/XAZSERVICEManualSamsung Color Laser Printer The keynote of ProductThe smallest / The lowest noiseHigh Quality Muti-path CLBP- Model : CLP-31x series- Speed(Color/Mono) : 4/16 ppm(A4). 4/17ppm(Let)- Printing resolution : Max. 2,400 x 600 dpi- Emulation : SPL-C- Memory : 32 MB (Network model : 32MB )- Processor : 360MHz- Interface : …
CLP-310N(172 pages) |
Canon
ENGIMPORTANT:Read this manual carefully before using your printer.Save this manual for future reference.User's GuideUser's GuideDownloaded from ManualsPrinter.com Manuals
…
lpb3360(338 pages) |
Epson
Start Here2 Slide the edge guides outward. Note: If loading legal-size paper, extend the cassette as shown. 3 Insert the paper with the printable side facedown. Note: Make sure the paper is loaded against the edge guide and not sticking out from the end of the cassette.4 Slide the edge guides against the paper, but not too tight. Make sure the p …
WorkForce Pro WP-4540(4 pages) |
Epson
CAUTIONEpson Stylus Photo 1500WINSTALLATION GUIDEMacProleMAC OS Xv20121015DO NOT INSTALL THE EPSON (OEM) INKS THAT WERE PROVIDED WITH THE PRINTER STORE THESE CAR-TRIDGES IN A SAFE PLACE AS THEY MAY BE REQUIRED IN THE FUTUREPOWER LOSS MAY CAUSE CARTRIDGE CHIP FAILURE. USE AN UNINTERRUPTIBLE POWER SUPPLY (UPS) TO AVOID ACCIDENTAL POWER LOSS.
…
Stylus Photo 1500W(16 pages) |
Epson
Great for slides, negatives and photos.Great for traditional and digital photography,the Epson Stylus Photo RX620 is the only all-in-one that restores and prints photos, slides and negatives without a PC.Key FeaturesView, select, crop and enlarge photos- Premium photo viewer and photo proof sheet make it easy to choose the photo, quantity, size, and paper ty …
RX620 - Stylus Photo Color Inkjet(2 pages) |
Miele Dishwasher G 686-3 Plus#14874O G 686-3 Plus: Miele Dishwasher Owner Documentation G 686-3 Plus, 68 |
CUMMINS Portable Generator DSKAACUMMINS Portable Generator Installation manual (File: cummins-dskaa-portable-generator-45, 22/08/2023) DSKAA, 45 |
Onkyo CD Player DV-C600Onkyo DV-C600 CD Player Instruction manual DV-C600, 44 |
Osram Light Fixture KREIOS FLOsram KREIOS FL Manual (Doc Type: Light Fixture Installation and safety instructions) KREIOS FL, 5 |
SICK Measuring Instruments GM901#8XB52G: GM901 Measuring Instruments Manual GM901, 24 |
Ruckus Wireless Gateway MediaFlex 7211Quick setup manual for Ruckus Wireless MediaFlex 7211 Gateway MediaFlex 7211, 2 |
Karcher Steam Cleaner SC 5.850 CSteam Cleaner Quick reference (Karcher SC 5.850 C) SC 5.850 C, 314 |
InStep Stroller RocketInStep Stroller Owner's manual (File: instep-rocket-owner-s-manual-12, Monday 18-09-2023) Rocket, 12 |
Toshiba Storage MK1216GSGSpecifications for Toshiba MK1216GSG Storage MK1216GSG, 2 |
Teac MP3 Player DV-RA1000HDTeac DV-RA1000HD MP3 Player Brochure DV-RA1000HD, 9 |
Mirage Speaker System NANOSATMirage NANOSAT Speaker System Owner's manual NANOSAT, 12 |
Napoleon Transmitter F-40User Guide: Napoleon F-40 (VZ9U8E, Upd.02/09/2023) F-40, 3 |