ADDON NHP5010 Operation & User’s Manual

Text of ADDON NHP5010 User Guide:

• ADDON NHP5010, NHP5010 User Manual 114 6.2 Joining an AVLN Network Assume that a network exists, a new device, the ‘joiner’, wants to join the network. Any device on the existing network can become the ‘adder’. Step1 Press the Security pushbutton on the ‘joiner’ for at least 10 seconds. The device will reset and restart with a random NMK. Step2 Press the Security pushbutton on the ‘joiner’ for less than 3 seconds. Step3 Press the Security pushbutton on any network device for less than 3 seconds, making it the ‘adder’. Please press this pushbutton within 1 m

• ADDON NHP5010, NHP5010 User Manual 7 3.3.2 Before You Begin Before you install the device, please pay attention to the following items:  When the device is connected to a computer, hub, router, or switch, the Ethernet cable should be shorter than 100 meters.  Place this device on a stable surface or support. Do not put this device on the ground.  Keep the device clean. Keep away the device from direct sunshine. Avoid any metal in the device.  Place the device in the center of the placement a

• ADDON NHP5010, NHP5010 User Manual 38 Field Description IP address Enter the WAN IP address provided by the ISP. It cannot be null. Subnet mask Enter the WAN subnet mask provided by the ISP. It varies depending on the network type. Usually, the subnet mask is 255.255.255.0 (Class C). Default Gateway IP Enter the IP address of the gateway provided by the ISP. This IP address is used for connecting to the ISP. MTU Set the maximum transmission unit. It is 1500 bytes for most Ethernet networks. But

• NHP5010 User Manual 33 5.2.2 Internet Setup Choose SETUP > Internet Setup, and the following page appears. This device supports Internet access modes. In this page, you can add multiple WAN connections and set the default gateway mode. You can manually or automatically set the default gateway mode. If you select Manual, you need to select a proper W

• ADDON NHP5010, NHP5010 User Manual 70 The following table describes parameters in this page: Field Description Transmission Rate Set the proper transmission rate. Transmit Power Select the proper transmission power from the drop- down list. You can select 100%, 80%, 60%, 40%, or 20%. Beacon Period Beacon period indicates the frequency of the PLC wireless router that sends the Beacon frame. By default, the PLC wireless router sends the beacon frame every other 100 ms. The range is 20~1024. RTS Threshold

• NHP5010 User Manual 103  HTTP Upgrade Mode If you select HTTP from the drop-down list of upgrade mode, the following page appears. The following table describes parameters in this page: Field Description Upgrade Mode Select HTTP. Server IP Address Enter the IP address of HTTP server. Server Port Enter the port number of HTTP server. User Name Enter th

• ADDON NHP5010, NHP5010 User Manual 10  Note: If multiple network cards are installed on your PC, a window other than the Local Area Connections Properties window may appears. Step 3 Double-click Internet Protocol (TCP/IP) and the Internet Protocol (TCP/IP) Properties window appears.

• ADDON NHP5010, NHP5010 User Manual 54 Field Description your router. Domain Name Server (Primary) IP Enter the IP address of the primary DNS server. Domain names should be resolved first by the primary DNS server. Domain Name Server (Secondary) IP If the ISP provides another DNS server, enter the IP address of DNS server. If the primary DNS server fails to resolve the domain name, the secondary will resolve it. After setting the parameters, click Apply to save the settings. 5.2.5 Time and Date Choose SETUP > Time and Date, and the following page appears. In this page, you can set the

• ADDON NHP5010, NHP5010 User Manual 61 The following table describes the paramters for configuring an IP address reserved for a MAC address: Field Description IP Enter an IP address for binding to a MAC address. MAC Enter a MAC address for binding to an IP.  Black List The black list means that if a MAC address of a LAN device is not consistent with the specified MAC address, the PLC wireless router does not assign the bound IP address to the device. Click Add under the BLACK LIST to display the following page.

• ADDON NHP5010, NHP5010 User Manual 46 The following table describes parameters related to the WEP mode: Field Description WEP Key Length Select the encryption length of WEP key. You can select 64 bit or 128 bit. Default Tx Key Select one from the four keys as the default key of the wireless network. WEP Key Format  When the key format is 64 bit, you need to enter 5 ASCII characters or 10 hexadecimal digits.  When the key format is 128 bit, you need to enter 13 ASCII characters or 26 hexadecimal digits. WEP Key 1/2/3/4 Set 64-bit or 128-bit key according to the key format. Authentication Select the proper authentication

• ADDON NHP5010, NHP5010 User Manual 59 The following table describes parameters in this page: Field Description MAC Enter the MAC address of the device that is not allowed to access the Internet. Comment Enter the comment about the MAC filtering rule. After setting the parameters, click Apply to save the settings. 5.3.2.2 DHCP Filtering DHCP Filtering is used to control network access based on the IP address of the network device. Choose Access Control > DHCP Filtering on the left pane or click DHCP Filtering in the ACCESS CONTROL page to display the foll

• ADDON NHP5010, NHP5010 User Manual 110 In this page, you can view basic information of the PLC wireless router, such as the information of WAN and LAN interfaces, wireless LAN information and DHCP server Information. Click Refresh to refresh the information in this page. 5.5.2 LAN Client Choose STATUS > LAN Clients, and the following page appears. In this page, you can view the status information of wireless clients, Ethernet clients, and DHCP clients. Click Refresh to refresh the information in this page. 5.5.3 Routing Table

• ADDON NHP5010, NHP5010 User Manual 90  Remote Device Configuration The Remote Device Configuration allows you to view the configuration information of the remote PLC devices and to set the network passwords of the remote devices. You can search current remote PLC devices by clicking the Scan button. Select Enable from the drop-down list of Change Remote NetworkPwd to display the following page. You can set the passwords of remote PLC devices according to their MAC addresses and DEKs (Device Equipment Key). The following table describes parameters in this page: Field Description Device Name Enter the device names of the remote devices. Remote

• ADDON NHP5010, NHP5010 User Manual 40 Field Description PPPoE Account Enter the user name provided by the ISP for PPPoE dialup. PPPoE Password Enter the password provided by the ISP for PPPoE dialup. Confirm Password Enter the PPPoE password again. Authentication Method You can select AUTO, PAP, CHAP, MS-CHAP, or EAP from the drop-down list. MTU Set the maximum transmission unit. It is 1500 bytes for most Ethernet networks, 1492 bytes for PPPoE connection. But some ISPs may require smaller MTUs. Do

• ADDON NHP5010, NHP5010 User Manual 97 The following table describes parameters in this page: Field Description Firmware Version Display current firmware version. Upgrade Mode Select FTP. Server IP Address Enter the IP address of FTP server. Server Port Enter the port number of FTP server. User Name Enter the username for connecting to the FTP server. Password Enter the password for connecting to the FTP server. Directory Enter the firmware directory. Clear Config If you check Clear Config, the PLC router restores to the default settings after upgrade. Otherwise, the PLC router keeps the current settings. �

• ADDON NHP5010, NHP5010 User Manual 27 Field Description  Mixed 802.11b/g: It is compatible with 802.11b and 802.11g.  Mixed 802.11n/g: It is compatible with 802.11n and 802.11g.  Mixed 802.11b/g/n: It is compatible with 802.11b, 802.11n, and 802.11g. Band Width You can set the band width only in the 802.11 mode that is compatible with 802.11n. For 20M bandwidth, the maximum rate is 130Mbps (150Mbps for short preamble); for 40M Upper (+) or 40M Lower (-) bandwidth, the maximum rate is 270Mbps (300Mbps for short preamble). Wireless Channel Select the working channel of the wireless network. The default is Auto Scan, which indicates that the w

• ADDON NHP5010, NHP5010 User Manual 29 Field Description WEP Key Length Select the encryption length of WEP key. You can select 64 bit or 128 bit. Default Tx Key Select one from the four keys as the default key of the wireless network. WEP Key Format  When the key format is 64 bit, you need to enter 5 ASCII characters or 10 hexadecimal digits.  When the key format is 128 bit, you need to enter 13 ASCII characters or 26 hexadecimal digits. WEP Key 1/2/3/4 Set 64-bit or 128-bit key according to the key format. Authentication Select the proper authentication mode. You can select Open or Share Key. (3) WPA-PSK S

• ADDON NHP5010, NHP5010 User Manual 57 5.3.2.1 MAC Filtering MAC (Media Access Control) address filter is used to filter the transmission data according to the physical address of wireless network card. Choose Access Control > MAC Filtering on the left pane or click MAC Filter in the ACCESS CONTROL page to display the following page.

• ADDON NHP5010, NHP5010 User Manual 58 In this page, you can add the MAC addresses of devices to the MAC filtering list. The devices in the MAC filtering list are not allowed to access the Internet. Check Enable MAC Filtering, and the following page appears. Click Add to display the following page.

• NHP5010 User Manual 4 The following table describes the status of LED indicators on the front panel: LED Indicator Color Status Description Power Green On System runs normally. Green Blink System is resetting. System is in the process of password synchronization. - Off Device is powered off or system is down. LAN1 Green On Connection via the LAN1

• ADDON NHP5010, NHP5010 User Manual 45 None means data encryption is not adopted and the network is not secure. Any station can access the network. This option is not recommended. (2) WEP Select WEP from the drop-down list of wireless security mode to display the following page.

• ADDON NHP5010, NHP5010 User Manual 96 The following table describes parameters in this page: Field Description Firmware Version Display current firmware version. Upgrade Mode Select TFTP. Server IP Address Enter the IP address of TFTP server. Server Port Enter the port number of TFTP server. Directory Enter the firmware directory. Clear Config If you check Clear Config, the PLC router restores to the default settings after upgrade. Otherwise, the PLC router keeps the current settings.  FTP Upgrade Mode If you select FTP from the drop-down list of upgrade mode, the following page appears.

• NHP5010 User Manual 98 The following table describes parameters in this page: Field Description Firmware Version Display current firmware version. Upgrade Mode Select HTTP. Server IP Address Enter the IP address of HTTP server. Server Port Enter the port number of HTTP server. User Name Enter the username for connecting to the HTTP server. Password Enter the

• ADDON NHP5010, NHP5010 User Manual 65 Click Add to display the following page. The following table describes parameters in this page: Field Description Port Range Enter the port filtering range. TCP/UDP You may select TCP, UDP, or Both. Remark Enter the comment about the port filtering rule.

Related Products and Documents (Network Router):

Comparable Devices:

Similar Resources:

• E-Lins EV700 Series (7 pages) E-Lins EV700 Series Router Quick Start E‐LinsTechnologyCo.,LimitedAdd:Bld22.,LongxiGarden,NonglinRD.,FutianDistrict,Shenzhen,518000,ChinaTel:+86‐755‐83700465E‐mail:sales@szelins. …

• Fortinet FortiGate 3000 (2 pages) © Copyright 2006 Fortinet Incorporated. All rights reserved. Products mentioned in this document are trademarks or registered trade-marks of their respective holders.Regulatory ComplianceFCC Class A Part 15 CSA/CUS5 July 2006Checking the Package ContentsConnectingPlanning the ConfigurationPOWERHi-Temp1 23INTEXT4/HAEsc Enter1 2 3 4/HA INTERNAL EXTERNAL1, 2, …

• Honeywell ST6300 (2 pages) ST6300ELECTRONIC PROGRAMMERHEATING CONTROLSFEATURES■One or two ON/OFF periods per day.■Built-in battery back-up.■Built-in start-up programme.■Clear digital display.■Ease of operation.■Temporary or permanent over-ridefacilities.■12 hour time display with am/pmindication.■Simple change to 24 hourclock display.■Programme indicator lights.■Do …

• Korenix JetNet 5010G Series (5 pages) IntroductionKorenixDemoKitisdesignedtodemonstrateKorenixproducts.InordertoletcustomersunderstandKorenixproducts’featuresandfunctionalityundervariouskindsofcircumstances,Korenixproducesthisportabledemobox.Inthislimitedboxspace,Korenixorganize …

• Black Box ME444A-530-R3 (1 pages) 1Black Box Corporation • 1000 Park Drive • Lawrence, PA 15055-1018 • Tech Support: 724-746-5500 • www.blackbox.com • e-mail: [email protected]/2/2004 #15035© 2004. All rights reserved.Black Box Corporation.Selectable speedsrange up to 256 kbps.Your choice ofinterfaces in desktopor rackmount cardmodels.Built-in BERT supportsV.54 loop diagnostics. …

• Uniden ENR1504 (55 pages) 2 TABLE OF CONTENTS WELCOME.................................................................................6 ENR1504 FEATURES ...............................................................7 Internet Access Features ................................................7 LAN Features ..................................................................8 Ro …

Comments, Questions and Opinions: