Manualios.com

Innoband 6000-B1 Operation & User’s Manual

Innoband 6000-B1 Manual Online:

4.2, 2082 votes
Innoband 6000-B1 User Manual
Innoband 6000-B1 User Guide
Innoband 6000-B1 Online Manual

Text of Innoband 6000-B1 User Guide:

  • Innoband 6000-B1, 6000-B1 User’s Guide 35 Click Add to add a Queue Configuration for parental control. Check Remove and click Remove to remove the specified entry. Click Save/Reboot to save the configuration. Figure 45: Add Quality of Service Queue Configuration Global Setting  Click Enable / Disable to activate / deactivate Queue Configuration for QoS.  Specify an egress interface for this Queue.  Choose between 1 to 3 queue precedence to set the entry.  Click Save/Reboot to save the configuration. QoS Classification You need to define o

  • Innoband 6000-B1, - 80 - Registration Card VDSL2/ADSL2+ Wireless Gateway 6000-B1 Product Registration Name / Company: Address: City/State/Zip: Phone: E-mail: Serial Number: Purchased from: Date of Purchase: Please cut out the above Product Registration Card and send in with a self-addressed stamped envelope to: Innoband Technologies, Inc. 2526 Qume Drive Ste 21, San Jose, CA 95131

  • Innoband 6000-B1, 6000-B1 User’s Guide 49 Global Setting  Enter the MAC Address of wireless client  Click Save/Apply to save the configuration. Wireless Bridge The wireless bridge feature is also known as WDS, Wireless Distribution System). Figure 64: Wireless Bridge Configuration Global Setting  Set the AP mode as Access Point or Wireless Bridge  When the AP mode is set to Wireless Bridge, you can enable or disable bridge restrictions. If you choose to enable bridge restriction, you must enter the proper remote bridges�

  • 6000-B1 User’s Guide 47  If the Network Authentication is WPA2-PSK (pre-shared key), enter the WPA Pre-Shared Key and enter WPA Group Rekey Interval, WPA Encryption Method (TKIP, AES, TKIP+AES), enable or disable WEP encryption. If WEP Encryption is enabled, select the Encryption Strength with 64bits or 128bits, select the current Key Index and enter t

  • Innoband 6000-B1, 6000-B1 User’s Guide 61 Appendix A - Configuring the Internet Settings This appendix provides instructions for configuring the Internet settings on your computers to work with the device. Configuring Ethernet PCs Before you begin By default, the device automatically assigns the required Internet settings to your PCs. You need to configure the PCs to accept this information when it is assigned. Note In some cases, you may want to assign Internet information manually to some or all of your computers rather than allow the device to do so. See Assigning static Internet information to your PCs section. 

  • Innoband 6000-B1, 6000-B1 User’s Guide 52 8 Diagnostic The Diagnostic web page provides the connection check of the physical layer and upper layer. The results are helpful to figure out the issue if you have a problem trying to surf Internet. Network Tests Fault Management Network Tests This page will show the result of a diagnostic test in physical layer like WAN port and also upper layer of PPP, if ISP provides the PPP access protocol. Figure 67: Diagnostic Result Global Setting:  Click the Next Connection to test another connection.  Click the Test to test it again  Click Test with OAM

  • Innoband 6000-B1, 6000-B1 User’s Guide 29 Figure 33: Add - Outgoing IP Filter Setup Global Setting  Enter the Filter Name  Select the Protocol from the selection list.  Enter the Source IP Address and Subnet Mask (range of IP addresses) of packet  Enter the one port or multi ports (port range)  Enter the Destination IP Address and Subnet Mask (range of IP addresses) of packet  Enter the one port or multi ports (port range)  Click Save/Apply By default, all incoming IP packets from WAN are blocked fro

  • Innoband 6000-B1, 6000-B1 User’s Guide 33 Global Setting  Enter the Username  Select the Browser’s MAC Address or Other MAC Address to enter the specific PC MAC address.  Check those days of the week you want to block above PC to surf Internet.  Enter the Start Blocking Time and End Blocking Time  Click Save/Apply. URL Filtering This feature allows you to configure the filter feature based on URL (Uniform Resource Locator) address. Filter rules allow you to prevent users on your network from a

  • 6000-B1 User’s Guide 58 selecting it. The following are the methods available for local and remote access:  FTP  HTTP  ICMP (Ping)  SSH  TELNET  TFTP  Click Save/Apply to save the configuration. IP Addresses Figure 77: Management Configuration – Access Control: IP Address Click to enable or di

  • Innoband 6000-B1, 6000-B1 User’s Guide 73 PPP Point-to-Point Protocol A protocol for serial data transmission that is used to carry IP (and other protocol) data between your ISP and your computer. The WAN interface on the device uses two forms of PPP called PPPoA and PPPoE. See PPPoA, PPPoE. PPPoA Point-to-Point Protocol over ATM One of the two types of PPP interfaces you can define for a Virtual Circuit (VC), the other type being PPPoE. You can define only one PPPoA interface per VC. PPPoE Point-to-Point Protocol over Ethernet One of t

  • 6000-B1 User’s Guide 66 Appendix B - Troubleshooting This appendix suggests solutions for problems you may encounter in installing or using the device, and provides instructions for using several IP utilities to diagnose problems. Contact Customer Support if these suggestions do not resolve the problem. Troubleshooting Suggestions Problem

  • - 82 - Appendix G - Contact information We would more than love to help if you have further technical questions, please visit our Website at http://www.innoband.com or send E-mail to [email protected] To purchase accessories or replacement parts for this gateway, please visit http://www.innocow.com Company Address Innoband Technologies, Inc 252

  • Innoband 6000-B1, 6000-B1 User’s Guide 68 IP address of a particular Internet location, you can use the nslookup command, as explained in the following section. From most other IP-enabled operating systems, you can execute the same command at a command prompt or through a system administration utility. Nslookup You can use the nslookup command to determine the IP address associated with an Internet site name. You specify the common name, and the nslookup command looks up the name on your DNS server (usuall

  • Innoband 6000-B1, 6000-B1 User’s Guide 48  If the Network Authentication is Mixed WPA2/WPA-PSK (pre-shared key), enter the WPA Pre-Shared Key and enter WPA Group Rekey Interval, WPA Encryption Method (TKIP, AES, TKIP+AES), enable or disable WEP encryption. If WEP Encryption is enabled, select the Encryption Strength with 64bits or 128bits, select the current Key Index and enter the key and four keys when necessary  Click Save/Apply to save the configuration. MAC Filter With this configuration, you could allow or den

  • Innoband 6000-B1, 6000-B1 User’s Guide 39 Global Setting  Select the Enabled option to activate this RIP service  Select the desired RIP version and operation, followed by placing a check in the 'Enabled' checkbox for the interface.  Click Save/Apply to save the configuration DNS The DNS feature provides two more setting pages including DNS server setting and Dynamic DNS. DNS Server Figure 52: DNS Configuration Global Setting  Check Enable Automatic Assigned DNS checkbox, this gateway will accept the f

  • Innoband 6000-B1, 6000-B1 User’s Guide 11 Testing your Setup Once you have connected your hardware and configured your PCs, any computer on your LAN should be able to use the device to access the Internet. To test the connection, turn on the device, wait seconds till device booting up and then verify that the LEDs are illuminated as follows: LED Behavior Power (PWR) Solid green to indicate that the device is turned on. If this light is not on, check the power cable attachment. Wireless (WLAN) Solid green to indicate that the Wireless LAN function is operational. Ethernet Solid green to indicate that the device can communicate with your LAN. DSL

  • Innoband 6000-B1, 6000-B1 User’s Guide 28 ALG An ALG (Application Layer Gateway) is a method to allow specific application to pass through NAT firewall. Figure 31: ALG configuration Global Setting  Check to select SIP ALG enabled  Click Save/Apply Security The Security feature provides two more setting pages including IP filtering in Route mode, MAC filtering and Parental Control. IP Address Filter The device can block the packet in outgoing and incoming directions. By default, all outgoing IP packets from LAN is allowed to surf Internet, but some IP packets can be

  • Innoband 6000-B1, 6000-B1 User’s Guide 37  Enter the Destination IP Address, Destination Subnet Mask, and UDP/TCP Destination Port (single port or port range (Port:Port)).  Enter Source MAC Address and Source MAC Mask  Enter Destination MAC Address and Destination MAC Mask  Select the 802.1q Priority from the list.  Click Apply to add this QoS class Routing The section shows the IP addresses or address routes for the computers connected to the gateway to reach different

  • Innoband 6000-B1, 6000-B1 User’s Guide 67 Problem Troubleshooting Suggestion I forgot/lost my user ID or password. If you have not changed the password from the default, try using “admin” as both the user ID and password. Otherwise, you can reset the device to the default configuration by pressing the Reset button on the back panel of the device. Then, type the default User ID and password shown above. WARNING: Resetting the device removes any custom settings and returns all settings to their default values. I cannot access

  • Innoband 6000-B1, 6000-B1 User’s Guide V Passwords ....................................................................................................................................... 59 Update Software ................................................................................................................... 60 Save / Reboot ........................................................................................................................ 60 Appendix A - Configuring the Internet Settings .......

  • Innoband 6000-B1, 6000-B1 User’s Guide 54 9 Management The Management web page menu comprises: Settings System Log TR-069 Client Internet Time Access Control Update Software Save/Reboot Settings This page allows you to backup the current configuration of the device, update the configuration, and restore default configuration (factory setting). Backup Figure 69: Backup Settings Click Backup Settings to backup the current settings of the device into a file in the PC. Update Figure 70: Restore Defaul

  • Innoband 6000-B1, 6000-B1 User’s Guide 17 6 Advanced Setup The Advance Setup menu includes the sub menus WAN, LAN, NAT, Security, Parental Control, Quality of Service, Routing, DNS, DSL, and Interface Group. WAN LAN NAT Security Parental Control Quality of Service Routing DNS DSL Interface Group WAN You can configure your internet connection from this page. This page displays the details of existing internet connection. The device allows 1 bridge connection and 1 route connection existing at that same time without VLAN setting. But if you need more than 1 bridge connection or 1 route connection, the VLAN tag is required. Plea

  • Innoband 6000-B1, 6000-B1 User’s Guide 62 Connection icon, and then select Properties. The Local Area Connection Properties dialog box is displayed with a list of currently installed network components. If the list includes Internet Protocol (TCP/IP), then the protocol has already been enabled. Skip to step 10. 5. If Internet Protocol (TCP/IP) does not display as an installed component, click Install. 6. In the Select Network Component Type dialog box, select Protocol, and then click Add. 7. Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click OK. You may be prompted to install files fr

  • 6000-B1 User’s Guide 15 Figure 10: Device ATM Statistic Information Figure 11: Device ADSL Statistic Information Figure 12: Device VDSL Statistic Information

  • Innoband 6000-B1, 6000-B1 User’s Guide 74 Telnet An interactive, character-based program used to access a remote computer. While HTTP (the web protocol) and FTP only allow you to download files from a remote computer, Telnet allows you to log into and use a computer from a remote location. TFTP Trivial File Transfer Protocol A protocol for file transfers, TFTP is easier to use than File Transfer Protocol (FTP) but not as capable or secure. TKIP Temporal Key Integrity Protocol (TKIP) provides WPA with a data encryption function. It ensures that a unique master key is generated for each packet, supports message integrity and sequencing

Related Products and Documents (Gateway):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Dell E157FP - 15" LCD Monitor Setup manual dell/e157fp-15-lcd-monitor-631.pdf 30 May 2023 2 2.77 Mb
2 Sony XM-604M Marketing Brochure sony/xm-604m-marketing-FHU.pdf 15 Nov 2023 1 0.35 Mb
3 Pacific energy SUMMIT Installation and operating instructions manual pacific-energy/summit-32G.pdf 12 Dec 2023 20
4 Canon IXUS700 Connection manual canon/ixus700-82R.pdf 29 Sep 2022 2 0.48 Mb
5 CAC / BDP BYPASS AND FAN POWERED HUMIDIFIERS Owner's manual cac-bdp/bypass-and-fan-powered-humidifiers-2AJ.pdf 22 Apr 2023 8
6 Rowenta COMPACTEO ERGO Instructions manual rowenta/compacteo-ergo-168.pdf 22 Dec 2023 64 3.44 Mb

Similar Resources:

  • Trilliant

    SecureMesh Gateway-2000

    (53 pages)
    Installation Guide forSecureMesh®WAN Gateway 2(GATE-2000)Document Number: PL-0073ARevision: Preliminary 1.0Date: September 18, 2020Trilliant Holdings Inc.401 Harrison Oaks Blvd., Suite 300Cary, North Carolina 27513 …
  • BURG WATCHER

    TSE 5001

    (21 pages)
    www.burg-waechter.deBURG-WÄCHTER KG Altenhofer Weg 15 58300 Wetter GermanyElektronisches TürschlossBUSINESS Montage- und Bedienungsanleitung Assembly and User Manual Instruction de montage et mode d’emploi Montage- en gebruiksaanwijzingGenial sicher.Genial einfach.SET 5003 E-KEYSET 5001 PINCODESET 5002 FINGERSCANBA/MA TSE Set 5001,5002,5003 dp/mri/d …
  • Technicolor

    TG582n

    (2 pages)
    CABLE SATELLITE TERRESTRIALTELECOMQUICK START GUIDE: TG582nNAME AND SECURITY DETAILSWELCOMEThank you for purchasing and making Technicolor gateways part of your broadband experience. For more information on your Technicolor gateway please visit us at:www.technicolor.comPACK CONTENTS*ADSL filters: The number of ADSL filters included with your gateway is det …
  • GE

    3500/91 EGD

    (4 pages)
    Specifications and Ordering Information Part Number 165361-01 Rev. D (06/07) Page 1 of 4 3500/91 EGD Communication Gateway Module Description The 3500/91 EGD (Ethernet Global Data) Communication Gateway modules provide comprehensive communication capabilities of 3500 rack-monitored values and status. This Ethernet network path provides informa …
  • SOMFY

    TaHoma

    (84 pages)
    TaHoma®Ref. 5069914B ÍRe{È4BBÎFR Notice InstallateurDE InstallationsanleitungNL Handleiding installateurEN Installer GuideDA InstallatørvejledningFI Asentajan opasSV Anvisningar för installatörerNO Installasjonshåndbok …
  • Patton electronics

    SMARTNODE 4520 Series

    (79 pages)
    SmartNode 4520 & 4110 SeriesVoIP Gateway RoutersUser ManualImportantThis is a Class A device and is intended for use in a light industrial environment. It is not intended nor approved for use in an industrial or residential environment.Sales Office: +1 (301) 975-1000Technical Support: +1 (301) 975-1007E-mail: [email protected]: www.patton.comPart …

Comments, Questions and Opinions: