Intek KT-950EE Instruction Manual
|
Intek KT-950EE, 3) Clockwise or counterclockwise rotation of DIAL knob to select the SAVE: ON/OFF 4) Press U/V key to save the setting. 5) Press MENU/LOCK or PTT , EXIT to normal operation. TOT (Time-out Timer) The TOT Feature provides a safety switch, which limits transmission time to a preprogrammed value. This will conserve battery power by limiting the length of transmissions . The TOT default is 180s. To adjust the timer, see the instructions below: 1) Press MENU/LOCK , rotate the DIAL knob, come to MENU [15]: TOT 2) Then press U/V key to enter the set mode. 3) Clockwise o
Intek KT-950EE, ADDITIONAL FUNCTIONS AND SETTINGS MEMORY CHANNEL STORAGE (Memory Channels 01-99) Store the Memory Channel according to the following instructions: - Select the desired frequency while operating in the VFO mode. Be sure to set up any desired CTCSS or DCS tones, as well as any repeater offset. - Press F/ALERT button, then press U/V key, Channel 01-99 will flash on the LCD, rotate DIAL knob to store the channel between channel 01-99. - Press U/V key to save the setting. - Repeat the process above, to store other channels. (Note: Repeater offset frequency should be set via programming software.) EMERGENCY ALARM FEATURE Press and hold the F/ALERT button about
Intek KT-950EE, 1) Press MENU/LOCK , rotate the DIAL knob, come to MENU [1]: RXCODE 2) Then press U/V key, enter the set mode. 3) Clockwise or counterclockwise rotation of DIAL knob to select from OFF /67.0-754N, press MENU/LOCK again, to select the code (Positive or negative), such as 023N---023I. NOTE: [CTCSS:67Hz---254.1Hz(50 groups); DCS:023N-754N(104 groups)] 4) Press U/V key to save the setting and EXIT. Press MENU/LOCK or PTT ,EXIT to normal operation. TXCODE Set the transmitting signal according to the below instructions: 1) Press MENU/LOCK , rotate the DIAL knob, come to MENU [2]: TXCODE 2) Then press U/V key, enter the set mode. 3) Clockwise
Intek KT-950EE, GETTING ACQUAINTED MENU/LOCK Key ANTENNA Jack SP. MIC. TX Indicator EXT DC Jack LCD PTT Switch F/ALERT Switch LAMP/FM Switch ON/OFF Key Microphone VOL/MON Key DIAL Knob U/V MODE Key Speaker PULL KNOB UP TO UNLOCK ! - 6 -
Intek KT-950EE, Press MENU/LOCK , turn clockwis e or counterclockwise DIAL , come to MENU [05] BEEP. Press MENU/LOCK , turn clockwis e or counterclockwise DIAL , come to MENU [06] VOX. Press MENU/LOCK , tur n clockwis e or counterclockwise DIAL , come to MENU [07] POWER. Pres s MENU/LOCK , turn clockwis e or counterclockwise DIAL , come to MENU [08] DW. - 12 -
Intek KT-950EE, MENU DESCRIPTION 13 14 15 16 17 18 Menu Item 1 2 3 4 5 6 7 8 9 10 11 12 Description RXCODE TXCODE SQL (Squelch) LIGHT (LCD Illumination) BEEP (Keypad Beeper) VOX POWER (RF Output Power) DW (Dual Watch/UHF&VHF) STEP OFFSET SHIFT STE (Tail Tone Elimination) W/N (Wide Band/Narrow Band) SAVE (Battery Saver) TOT (Time out Timer) SCANM (Scan Mode) RELAYM (Repeater Sound Response) BCLO (Busy Channel Lock-out) Settings OFF'CTCSS, DCS OFF'CTCSS, DCS 0---9 OFF/ON /Key OFF--ON OFF/1---9
Intek KT-950EE, Pres s MENU/LOCK , turn clockwis e or counterclockwise DIAL , come to MENU [17] RELAYM. Pres s MENU/LOCK , turn clockwis e or counterclockwise DIAL , come to MENU [18] BCLO. - Press the key UV/MODE confirm the setting , and EXIT the function s setting. - Battery Save, Time-out Limit, Width/Narrow, only be changed via program software. - Under the VFO mode, turn clockwise or counterclockwise DIAL to increase or decrease the frequency. Pres s MENU/LOCK , turn clockwis e or counterclockwise DIAL , come to MENU [19] PRI. - 15 -
W/N (Wide/Narrow Band Selection) 1) Press MENU/LOCK , rotate the DIAL knob, come to MENU [13]: W/N 2) Then press U/V key to enter the set mode. 3) Clockwise or counterclockwise rotation of DIAL knob to select the WIDE/NARROW: 4) Press U/V key to save the setting. 5) Press MENU/LOCK or PTT , EXIT to norma l operation. SAVE (Battery Saver) The radio includes a u
Intek KT-950EE, NOTICE ! It is recommended to carefully read this owner’s manual before using the product. This will also help the user to prevent using the radio in violation of the regulations valid in the country where the product is used, as well as to avoid any possible interferences with other services. NOTICE ! This transceiver is programmable via PC, using the dedicated software and the PC interface cable (optional items). Any programming or modification of the original default setting must be made by a specialised technician or by an authorised service centre. Some functions of this transcei
To select the scanning mode, please see below: 1) Press MENU/LOCK , rotate the DIAL knob, come to MENU [16]: SCANM 2) Then press U/V key to enter the set mode. 3) Clockwise or counterclockwise rotation of DIAL knob to select the SCANM: TO/CO 4) Press U/V key to save the setting. 5) Press MENU/LOCK or PTT , EXIT to normal operation. ELAYM (Repeater Sound Response) When the feature is activated
Intek KT-950EE, Press MENU/LOCK , tur n clockwis e or counterclockwise DIAL , come to MENU [13] W/N. Pres s MENU/LOCK , turn clockwis e or counterclockwise DIAL , come to MENU[14] SAVE. Pres s MENU/LOCK , turn clockwis e or counterclockwise DIAL , come to MENU [15] TOT.. Pres s MENU/LOCK , turn clockwis e or counterclockwise DIAL , come to MENU[16] SCANM. - 14 -
Intek KT-950EE, TROUBLESHOOTING GUIDE No Power Can't Communicate with Other Group Members PROBLEMS Check battery installation and/or replace batteries. SOLUTIONS Voltage Capacity Quickly Goes Out The battery life is over, replace new one. Hear the Voice from Other Groups Verify that the frequency and the CTCSS you are using are the same as those of your group members. Change your CTCSS for the channel. You also need the CTCSS for all the radios in your group. 1) Under the FM radio frequency mode, set the fr
Intek KT-950EE, Optional Accessories ANTENNA INSTALLATION The supplied antenna provides good results over the entire frequency range of the transceiver. However, for enhanced based station medium-wave and shortwave reception, you may wish to connect an external antenna, as the supplied antenna is very smal l and can not be expecte d to provid e high performance at these frequencies. To install the supplied antenna, hold the bottom end of the antenn a and scre w it onto the matin g connecto r on the transceiver until it is snug. Do not over-tighten by use of extreme force. (See PIC 1) INSTALLATION OF ACCESSORIES Antenna PIC 1 - 2 - - EM-950 Externa
Intek KT-950EE, 1) Press MENU/LOCK , rotate the DIAL knob, come to MENU [5]: BEEP 2) Then press U/V key to enter the set mode. 3) Clockwise or counterclockwise rotation of DIAL knob to set ON/OFF 4) Press U/V key to save the setting. 5) Press MENU/LOCK orPTT , EXIT to normal operation. (ON-The beeper being activated, LCD displays icon. OFF- The beeper being disabled.) VOX ( VOICE OPERATED TRANSMISSION ) VOX eliminate s the necessit y of manuall y switchin g to the transmission Mode each time you want to transmit. The transceiver automaticall y switches to transmissio n mode when the VOX circuitr y sense s tha t you
Intek KT-950EE, LIGHT (LCD ILLUMINATION ON/KEY/OFF) includes a reddish illumination lamp which aids in nighttime operation. The red illumination yields clear viewing of the display in a dark environment, with minimal degradation of your night vision. Three options for activating the lamp are provided: Key: Illuminates the LCD when any key pressed. ON: Illuminates the LCD continuously. OFF: Disables the LCD lamp. Here is the procedure for setting up the Lamp mode: 1) Press MENU/LOCK , rotate the DIAL knob, come to MENU [4]: LIGHT. 2) Then press U/V key to enter the set mode. 3) Clockwise or counterclockwise rotation of DIAL knob to set ON/OFF/KEy 4) Press U/V key to s
- 32 - General Information Important notice ! The use of VHF and UHF FM transceivers is subject to the regulations applied in the country where the product has to be used. As regulations are usually subject to possible modifications, please check the current regulations in your country with your dealer or local supplier. INTEK does not take any responsibility for illegal use and operation of this
Intek KT-950EE, Press MENU/LOCK , come to MEN U [01]RXCODE MENU SETTING Press MENU/LOCK , tur n clockwis e or counterclockwis e DIAL , come to MENU [02]TX CODE. Pres s MENU/LOCK , tur n clockwis e or counterclockwise DIAL , come to MENU [03] SQL. Press MENU/LOCK , tur n clockwis e or counterclockwise DIAL , come to MENU [04] LIGHT. - 11 -
Intek KT-950EE, EXTERNAL EAR-MIC INSTALLATION Insert the optional earset/microphone plugs into the SP.&MIC. Jacks of the transceiver. (See PIC 3) PIC 3 PIC 2 Note: Never transmit without having an antenna connected. When installing the supplied antenna, never hold the upper part of antenna while screwing it onto the mating connector on the transceiver. If using an external antenna for transmission, ensure that the SWR presented to the transceiver is 1.5:1 or lower, to avoid excessive feed line loss. BELT CLIP INSTALLATION I
Intek KT-950EE, - Refer service to qualified technicians only. - Do not disassemble or modify the transceiver for any reason. - Do not expose the transceiver under direct sunlight long or to extremely hot condition. - Do not place the transceiver on the unstable surface. - Keep the transceiver out of dust, moisture, water. - Do not operate the transceiver or charge the battery pack under explosive conditions. PRECAUTIONS It is important that the operator is aware of and understands hazards common to the operation of any transceiver. SAFETY WARNING Please turn the transceiver off at the following locations: In explosive atmospheres (infl
DOWNLOAD |
Intek M-490 Plus Radio Service manual
M-490 Plus |
Intek KT-980HP Radio Instruction manual
KT-980HP |
Intek HR-200S Radio Owner's manual
HR-200S |
Intek DRS-5070 Radio Owner's manual
DRS-5070 |
Intek H-520 PLUS Radio Owner's manual
H-520 PLUS |
Intek M-899 VOX Radio Owner's manual
M-899 VOX |
Intek KT-930EE Radio Instruction manual
KT-930EE |
Intek M-100 PLUS Radio Owner's manual
M-100 PLUS |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | iHome | iP15 | Instruction manual | ihome/ip15-53Z.pdf | 02 Jul 2023 | 8 | |
2 | Toshiba | TDP-S80U | Specifications | toshiba/tdp-s80u-17C.pdf | 27 Aug 2022 | 1 | 0.04 Mb |
3 | Dell | Inspiron 20-3045 | Operation & user’s manual | dell/inspiron-20-3045-8QX.pdf | 16 Mar 2023 | 102 | |
4 | Philips | AJ3180 | Operation & user’s manual | philips/aj3180-AVC.pdf | 21 Sep 2022 | 2 | 0.38 Mb |
5 | Avaya | Tristar | Operation & user’s manual | avaya/tristar-5NB.pdf | 29 Oct 2023 | 2 | 0.3 Mb |
6 | Goldair | GCDF140B | Operating instructions | goldair/gcdf140b-ZQ7.pdf | 20 Jul 2023 | 5 |
Vertex Standard
VX-1400OPERATING MANUALVERTEX STANDARD CO., LTD.4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, JapanVERTEX STANDARDUS Headquarters10900 Walker Street, Cypress, CA 90630, U.S.A.YAESU UK LTD.Unit 12, Sun Valley Business Park, Winnall CloseWinchester, Hampshire, SO23 0LB, U.K.VERTEX STANDARD HK LTD.Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,Kwun Tong, Ko …
VX-1400(56 pages) |
Sangean
DDR-3FM RDS/DAB digital radioPlease read this manual before useA WORLD OF LISTENINGGBOperating instructionWARNING:TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DONOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.THE LIGHTNING FLASH ANDARROW- HEAD WITHIN THETRIANGLE IS A WARNING SIGNALERTING YOU OF“DANGEROUS VOLTAGE”INSIDE THE RADIO.CAUTION: TO REDUCE THE RISK OFEL …
DDR-3(24 pages) |
Tivoli Audio
FMOFFAMBTItaliano Per ottenere la versione più aggiornata del manuale utente vai su: http://tivoliaudio.com/palbtmanual.pdfNederlands Download de complete en meest recente multi-language handleiding op: http://tivoliaudio.com/palbtmanual.pdfNorsk Last ned komplett multi språklig manual på: http://tivoliaudio.com/palbtmanual.pdfSuomi Lataa viimeisin tä …
PAL BT(72 pages) |
Kenwood
KTC-9090DABDAB HIDEAWAY TUNER 3 page 2- 29INSTRUCTION MANUALMODE D’EMPLOISINTONIZADOR EXTRAÍBLE DAB 3 página 58 - 85MANUAL DE INSTRUCCIONES© PRINTED IN JAPAN B64-1748-10 / 02 (E) (DT)SYNTONISEUR DAB ESCAMOTABLE 3 page 30 - 57
…
KTC-9090DAB(88 pages) |
Delphi
GuideInstallationSKYFi2™H o m e a n d Ve h i c l e K i t sContents:SKYFi2Vehicle Adapter Kit Setup . . . . . . . . . . . . 2SKYFi2 Installation . . . . . . . . . . . . . . . . . . . . . . . . 7XM Antenna Setup . . . . . . . . . . . . . . . . . . . . . . . . 12SKYFi2 Home Adapter Kit Setup. . . . . . . . . . . . . 14Warranty . . . . . . . . . . . . . . . . …
SkyFi2 SA10102(20 pages) |
ELECRAFT
ELECRAFT K3 HIGH-PERFORMANCE 160 – 6 METER TRANSCEIVER K3 KIT ASSEMBLY MANUAL Rev L8, January 18, 2013 Copyright © 2013, Elecraft, Inc. All Rights Reserved
…
K3(84 pages) |
Shure Microphone 515BSMShure 515BSM Manual (Doc Type: Microphone Operation & user’s manual) 515BSM, 2 |
American Audio Amplifier Professional Power AmplifierAmerican Audio Product Manual: Professional Power Amplifier PDF User instructions - G1F26L Professional Power Amplifier, 16 |
Dell Desktop Studio XPS 435 MTPDF Guide (@7GLT49), Dell Studio XPS 435 MT Desktop (Sunday 31-12-2023) Studio XPS 435 MT, 40 |
Garmin Autopilot System GHP 20 Marine Autopilot System for Steer-by-WireGarmin GHP 20 Marine Autopilot System for Steer-by-Wire User Manual (Doc Type: Autopilot System Installation instructions manual) GHP 20 Marine Autopilot System for Steer-by-Wire, 22 |
Philips Headphone SHE3623Philips Headphone Specifications (File: philips-she3623-specifications-2, 28/02/2024) SHE3623, 2 |
Raychem Controller C910-485C910-485 (Controller ePDF Guide, #15S6RM) C910-485, 54 |
VICOR Power Supply PFC MicroPDF User Manual (@QM323T), VICOR PFC Micro Power Supply (01/03/2024) PFC Micro, 25 |
TRENDnet Other TEW-648UBMOther Quick installation manual (TRENDnet TEW-648UBM) TEW-648UBM, 13 |
Spectron Tuner SPH1100MP3#A11186: SPH1100MP3 Tuner Instruction manual SPH1100MP3, 24 |
TSI Quest Measuring Instruments Soundpro SE SeriesSoundpro SE Series Operation & user’s manual - P139EH Soundpro SE Series, 155 |
D-Link Network Hardware DGS-1500-20Network Hardware Operation & user’s manual (D-Link DGS-1500-20) DGS-1500-20, 93 |
Soundstream DVD Player VCM-7DVDVCM-7DVD Owner's manual - BKT4DH VCM-7DVD, 17 |