Manualios.com

Hamlet HRDSL512 Operation & User’s Manual

Hamlet HRDSL512 Manual Online:

4.2, 1387 votes
Hamlet HRDSL512 User Manual
Hamlet HRDSL512 User Guide
Hamlet HRDSL512 Online Manual

Text of Hamlet HRDSL512 User Guide:

  • User Manual HRDSL512/HRDSL512P4 55 Chapter 5 Troubleshooting If the ADSL2+ Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save your time and effort but if the symptoms persist, then consult your service provider. Problems starting up the router Problem Corrective Actio

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 9 2.3 The Front LEDs ADSL2+ Ethernet Modem (HRDSL512) ADSL2+ Router with 4-port Switch (HRDSL512P4) LED Meaning PPP Lit steady when there is a PPPoA / PPPoE connection. ADSL Lit when successfully connected to an ADSL DSLAM (“linesync”). LAN Lit when connected to an Ethernet device. Green for 100Mbps; Orange for 10Mbps. Blinking when data is Transmitted / Received. SYS Lit when the system is ready. PWR Lit when power is ON.

  • User Manual HRDSL512/HRDSL512P4 8 Chapter 2 Installing the ADSL2+ Router 2.1 Important notes for using the ADSL2+ Router ! ! Do not use the router in high humidity or high temperatures. ! ! Do not use the same power source for the router as other equipment. ! ! Do not open or repair the case yourself. If the router is too hot, turn off the power im

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 16 Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button and click OK.

  • User Manual HRDSL512/HRDSL512P4 43 4.4.4 UPnP UPnP offers peer-to-peer network connectivity for PCs and other network devices, along with control and data transfer between devices. UPnP offers many advantages for users running NAT routers through UPnP NAT Traversal, and on supported systems makes tasks such as port forwarding much easier by letting the app

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 49 4.6 Status 4.6.1 Device Info Device Information Firmware version: This is the Firmware version MAC Address: This is the MAC Address LAN IP Address: LAN port IP address. Sub Net Mask: LAN port IP subnet mask. DHCP Server: LAN port DHCP role - Enabled, Relay or disabled

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 37 4.3.4 ADSL ADSL Mode: The default setting is Auto Sync-UP. This mode will automatically detect your ADSL, ADSL2+, ADSL2, G.dmt, G.lite, and T1.413. But in some area, multimode cannot detect the ADSL line code well. If it is the case, please adjust the ADSL line code to G.dmt or T1.413 first. If it still fails, please try the other values such as ALCTL, ADI, etc. ADSL Type: There are five modes “Open Annex Type and Follow DSLAM’s Setting”, ”Annex A”, ”Annex I”, “An

  • User Manual HRDSL512/HRDSL512P4 26 ATM VC Virtual Circuit: VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define a virtual circuit. PVC Summary: VPI: The valid range for the VPI is 0 to 255. Enter the VPI assigned to you. This field may already be configured. VCI: The valid range for the VCI is 32 to 65535. Enter the VCI assigned to

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 5 1.2 Features of the ADSL2+ Router ADSL Multi-Mode Standard supports downstream rates of up to 24 Mbps and upstream rates of up to 1 Mbps. It also supports rate management that allows ADSL subscribers to select an Internet access speed suiting their needs and budgets. It is compliant with Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt(G.992.1); G.lite(G992.2)), G.hs (G994.1), G.dmt.bis (G.992.3), G.dmt.bisplus (G.992.5)). The Annex A and B are supported in different H/W platforms. Fast Ethernet Switch A 10/100Mbps

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 30 Firewall: " " Enabled: As set in default setting, it activates your firewall function. " " Disabled: It disables the firewall function. SPI: " " Enabled: As set in default setting, it activates your SPI function. " " Disabled: It disables the SPI function. 4.3.2 Routing If you have another router with a LAN-to-LAN connection, you may create a static routing on the router that is the gateway to Internet. #: Item number Dest IP: IP address

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 4 for a hacker to target a machine on your network. Secondly, it can block and redirect certain ports to limit the services that outside users can access. For example, to ensure that games and other Internet applications will run properly, user can open some specific ports for outside users to access internal services in network. Integrated DHCP (Dynamic Host Control Protocol) services, client and server, allow multiple users to get their IP addresses automatically on boot up from the product. Simply set local machines as a DHCP client to accept a dynamically assigned IP address from DHCP server and reboot. Each time loca

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 52 4.6.3 Statistics Read-only information here includes port status and packet specific statistics. Also provided are "Transmit Statistics" and "Receive Statistics". Ethernet Interface: This field displays the type of port Transmit Frames: This field displays the number of frames transmitted in the last second. Transmit Multicast Frames: This field displays the number of multicast frames transmitted in the last second. Transmit total Bytes: This field displays the number of bytes transmitted in the last second. Transmit Collision: This is the number of collisions on this port. Transmit Error Fram

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 18 3.3 LAN and WAN Port Addresses The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below. LAN Port WAN Port IP address 192.168.1.254 Subnet Mask 255.255.255.0 DHCP server function Enabled IP addresses for distribution to PCs 100 IP addresses continuing from 192.168.1.100 through 192.168.1.199 The PPPoE function is enabled to automatically get the WAN port configuration from the ISP, but you have to set the username and password first. 3.4 Information from your ISP Before configuring this device, you have to

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 50 WAN Status: “Not connected” or “Connected” Virtual Circuit: There are eight groups of PVC can be defined. VPI: The valid range for the VPI is 0 to 255 VCI: The valid range for the VCI is 32 to 65535 Connection Type: Name of the WAN connection. VPI/VCI: Virtual Path Identifier and Virtual Channel Identifier IP Address: WAN port IP address. Subnet mask: WAN port IP subnet mask. Default Gateway: The IP address of the default gateway. DNS Server: WAN port DHCP role - Enabled, Relay or disabled ADSL ADSL firmware version: This is the DSL firmware version associated with your router Line State: This is the sta

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 6 Firewall Supports simple firewall with NAT technology and provides option for blocking access from Internet, like Telnet, FTP, TFTP, WEB, SNMP and IGMP. Domain Name System (DNS) relay Provides an easy way to map the domain name (a friendly name for users such as www.yahoo.com) and IP address. When a local machine sets its DNS server with this router’s IP address, every DNS conversion request packet from the PC to this router will be forwarded to the real DNS in the outside network. Dynamic Domain Name System (DDNS) The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname. This dynamic IP address is the WAN IP

  • User Manual HRDSL512/HRDSL512P4 44 4.4.5 DDNS The Dynamic DNS function allows you to alias a dynamic IP address to a static hostname, allowing users whose ISP does not assign them a static IP address to use a domain name. This is especially useful for hosting servers via your ADSL connection, so that anyone wishing to connect to you may use your domain name, rather than h

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 47 DO NOT power down the router or interrupt the firmware upgrading while it is still in process. Improper operation could damage the router. UPGRADE: Click UPGRADE to begin the upload process. This process may take up to two minutes. After two minutes, log in again and check your new firmware version in the System Status screen. If the upload was not successful, the following screen will appear. Click Back to go back to the Firmware screen. 4.5.4 SysRestart Click SysRestart with option Current Settings to reboot your r

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 35 IP Address Mapping Rule Index: Choose the rule number. Rule Type: One-to-one: This is the mode maps one local IP address to one global IP address. Note that port numbers do not change for the One-to-one NAT mapping type. Many-to-One: This is the mode maps multiple local IP addresses to one global IP address. This is equivalent to Many to One (i.e., PAT, port address translation). Many-to-Many Overload: This is mode maps multiple local IP addresses to shared global IP addresses. Many-to-Many No Overload: This is the mode maps each local IP address to unique global IP addresses. Server: This type allow

  • User Manual HRDSL512/HRDSL512P4 40 Source IP Address: The source IP address or range of packets to be monitored. Subnet Mask: It is the source IP addresses based on above source subnet IP Source Port Number: This Port or Port Ranges defines the port allowed to be used by the Remote/WAN to connect to the application. Default is set from range 0 ~ 65535. It

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 32 4.3.3 NAT The NAT (Network Address Translation - NAT, RFC 1631) is the translation of the IP address of a host in a packet. The default setting is Dynamic NAPT. It provides dynamic Network Address Translation capability between LAN and multiple WAN connections, and the LAN traffic is routed to appropriate WAN connections based on the destination IP addresses and Route Table. This eliminates the need for the static NAT session configuration between multiple LAN clients and multiple WAN connectio

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 36 Public End IP: This is the ending Inside Public IP Address. This field is N/A for One-to-one, Many-to-One and Server mapping types. U sing port forwarding does have security implications, as outside users will be able to connect to PCs on your net work. For this reason you are advised to use specific Virtual Server entries just for the ports your application requires, instead of using DMZ. A s doing so will result in all connections from the WA

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 41 Application Filter Application Filter: Select this option to Activated/Deactivated the Application filter. ICQ: Select this option to Allow/Deny ICQ. MSN: Select this option to Allow/Deny MSN. YMSG: Select this option to Allow/Deny Yahoo messenger. Real Audio/Video: Select this option to Allow/Deny Real Audio/Video. URL Filter

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 28 RIP Direction: Select this option to specify the RIP direction. None is for disabling the RIP function. Both means the ADSL Router will periodically send routing information and accept routing information then incorporate into routing table. IN only means the ADLS router will only accept but will not send RIP packet. OUT only means the ADLS router will only send but will not accept RIP packet. Multicast: IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to establish membership in a Multicast group - it is not used to carry user data. The router supports both IGMP version 1 (IGMP-v1) and IGMP-v2. Selec

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 17 3.2 Factory Default Settings Before configuring your Modem/Router, you need to know the following default settings. Web Interface Username: admin Password: hamlet LAN Device IP Settings IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 ISP setting in WAN site PPPoE DHCP server DHCP server is enabled. Start IP Address: 192.168.1.100 IP pool counts: 100 3.2.1 Username and Password The default username and password are “admin” and “hamlet” respectively. If you ever forget the password to log in, you may press the RESET button up to 6 seconds to restore the factory default settings.

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 3 Chapter 1 Introduction the ADSL2+ Router 1.1 Introducing the ADSL2+ Router Welcome to the ADSL2+ Router. Your router is an “all-in-one” unit, combining an ADSL modem, ADSL router and Ethernet network switch, providing everything you need to get the machines on your network connected to the Internet over your ADSL broadband connection. The router complies with ADSL2+ standards for worldwide deployment and supports downstream rates of up to 24 Mbps and upstream rates of up to 1 Mbps. It is designed for small office, home office and residential users, enabling even faster speed Internet connections. User can enjoy ADSL servi

  • Hamlet HRDSL512, User Manual HRDSL512/HRDSL512P4 14 Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration.

More Instructions:

DOWNLOAD

Related Products and Documents (Modem):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Cisco MGX 8950 Product overview cisco/mgx-8950-125.pdf 14 Jan 2023 4 0.1 Mb
2 Airlink101 AR420W Quick installation manual airlink101/ar420w-VR5.pdf 28 Nov 2022 11 0.47 Mb
3 Troy-Bilt 1904 Owner's manual troy-bilt/1904-D5Z.pdf 02 Aug 2022 36 4.86 Mb
4 Pioneer S-IW691L Operating instructions manual pioneer/s-iw691l-7IK.pdf 31 Dec 2022 16
5 Smeg SER63LPG Instruction manual smeg/ser63lpg-9PC.pdf 25 May 2023 20 0.68 Mb
6 Teac SR-80iDAB Owner's manual teac/sr-80idab-6LT.pdf 10 Oct 2023 40 0.81 Mb

Similar Resources:

  • Encore

    ENF656-ESW-MOPR

    (14 pages)
    Motorola SM56 Software Modems Quick Start User's Guide Contents 1 Introduction 2 Preparing The Computer For Installation 3 Installing The Modem Hardware 4 Installing The Modem on Windows 9x, Millennium, Windows 2000 and Windows XP. 5 Installing The Modem on Windows NT 4.0 6 Verifying Correct Installation 7 Troubleshooting 8 Un-installing and Upgr …
  • Victron energy

    GX LTE 4G Series

    (9 pages)
    2020-08-01 15:42 1/9 GX LTE 4G - ManualVictron Energy - https://www.victronenergy.com/live/GX LTE 4G - ManualNOTE: DRAFT MANUAL. FIRST STOCK EXPECTED IN 2020 Q41. Introduction1.1 Product descriptionThe GX LTE is an accessory for GX-devices. It is a cellular 2G, 3G and 4G modem; providing a mobileinternet for the system and connection to Victron Remote Manage …
  • Westermo

    ODW-710-F1

    (28 pages)
    ©Westermo Teleindustri ABUser Guide6651-2201Industrial Converter PROFIBUS DP to Fibre Optic Link. Point to Point applicationswww.westermo.comODW-710-F1 Fibre Optic Modem …
  • Raymar

    MIU14.4L

    (43 pages)
    0049-0867-01X 2nd Generation MIU14.4L – USER’S GUIDE 6/22/2011 Rev. A MIU14.4L Industrial Grade Leased Line Modems User’s Guide …
  • Steren

    300-995

    (2 pages)
    Before using your new ADSL filter, please read the following recommendationsIMPORTANTDo not expose to extreme temperatures.Warranty is void if you open the device.Do not install the device where there is humidity.FEATURESADSL Filter for connections with ADSL internet or similar to accept voice and data. Improved performance by eliminating noises …
  • GSS

    GLC 100

    (32 pages)
    EnglishCLASSKLASSEGSS Grundig SAT Systems GmbHBeuthener Strasse 43D-90471 NurembergPhone: +49 (0) 911 / 703 8877Fax: +49 (0) 911 / 703 9210E-mail: [email protected]: http://www.gss.de/enGLC 100Ethernet over Coax …

Comments, Questions and Opinions: