HID HDPii Operation & User’s Manual

Text of HID HDPii User Guide:

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 28 Pause in the lower right. The Cancel button Use this button to cancel print jobs and reset the Printer for the next print job. Cancel now has two options: • Cancel single job in memory. • Cancel all jobs in memory. This Cancel All function will cancel all print jobs in the Printer and will completely reset the Printer. In this case, be sure to cancel the print jobs from the PC before pressing YES. The Pause button Use this button to pause the Printer at any time during operation. Note the Printer will always finish its current task before pausing. When the Printer is paused

• HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 97 Reviewing the YMCK Self Test Step Procedure 1 Use this card to confirm that image colors are properly reproduced. Image consists of sixteen graduated steps of RGB and YMCK. (Note: This print will provide maximum image size, giving complete card Coverage on a CR-80 sized card.)

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 203 Conducting the Tape Adhesion Test It is important to conduct tape adhesion tests because Fargo cannot be certain which transfer temperature and Dwell Time will work best (when printing cards other than UltraCard III or HDP-PVC). (Note: The optimal transfer settings may vary from card type to card type.) Caution: Inadequate time and temperature could produce cards that are more vulnerable to accelerated wear and dye migration. Use sufficient time and temperature to transfer HDP Film to the card to ensure a l

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 225 Using the Add and Delete buttons Step Procedure 1 Use the Add button for these capabilities: • Add an area default sized to .2 (at location “0” with focus on the added area). • Add multiple areas in the same location with the same affect (as if there were only one area). (Note: Intersecting/overlapping areas do not cancel each other out; instead, they act as one area.) 2 Using the Delete button to delet

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 266 Using the Mag Top of Form Option Use this option only if the Printer has a built-in Magnetic Stripe Encoder. • If so, use this option to shift the starting point of where the Printer will begin encoding the magnetic track data on a card's Magnetic Stripe. • When adjusting this value, keep in mind that a card and its Magnetic Stripe will always remain in the same relative position as the card travels through the Printer. The diagram (below) represents: • How the magnetic data will move in relation to the fixed position of a card's Magnetic Stripe a

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 146 Using the Help page The Help page displays the Help information. Step Procedure 1 Open this web page at the appropriate location by clicking on the Help book icon at the top of each page. See the previous procedure. 2 Review the web interface for the Ethernet-enabled Printer. Additional Procedures Accessing the Ethernet Status LED The Ethernet Status LEDs can be found on the back of Printers. Reviewing the HDPii LED Table LED Flash Rate Indicates Green LED (Left) On The Network link is present. Off The

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 47 Step Procedure 2 Remove the protective sleeve from the Card Cleaning Roller. Step Procedure 3 Insert the Card Cleaning Roller into the card input area.

• HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 193 Step Procedure 2 For the Image Quality slider bar controls, see below. • Click OK to accept any variance from the default (for this specific slider bar) and return to the Image Color tab window. • Click Cancel to negate any variance on the slide and return to the Image Color tab window. • Click

• HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 77 No Mag Module (PC Error Message No. 31) MAG encoding job sent to Printer without MAG encoder. You are trying to send encoding data, but the Printer is not configured with this Encoder type. No MiFare Encoder (PC Error Message No. 203) You are trying to send encoding data, but the Printer is

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 44 Loading the Clear HDP Transfer Film Step Procedure 1 Load the HDP Film into the HDP Film Cartridge until the rolls click. Step Procedure 2 Tighten the HDP Film.

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 223 Using the Scroll controls Controls Description Horizontal changes the size of the area from left to right • Default = 0.200 inches (5.1 mm) • Upper Limit = 3.450 inches (87.6 mm) • Lower Limit = 0.200 (cannot be null) Vertical changes the size of the area from top to bottom • Default = 0.200 • Upper limit = 2.183 • Lower limit = 0.200 (cannot be null) Defines the X coordinate for the lower left corner of the area • Default = 0.000 • Upper limit = 3.247 • Lower limit = 0.000

• HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 49 Adjustable Film Cartridge Details  Please note that not all cartridges need to be adjusted. Please perform this adjustment on printers that exhibit the walking issue described below. Only adjust the cartridge if the film is walking towards either flange and is not tracking

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 5 Using the Printer page _________________________________________________________________ 123 Using the System Log page ____________________________________________________________ 126 Changing the Log Name _____________________________________________________________ 127 Selecting the Log Type ______________________________________________________________ 128 Selecting the Log Destination _________________________________________________________ 129 Setting up Email Event logging _______________________________________________________ 131 Specifying UDP Event loggin

• HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 72 No. 159) Calibrate Ribbon (PC Error Message Nos. 128 and 170) The print Ribbon Sensor is out of calibration. Select Cancel and then perform the Ribbon calibration procedure. Card Feed Stop (PC Error Message No. 137) The Front Cover was opened. This caused the card transfer

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 306 Pinch Roller A free spinning (non-driven) Roller that presses the card against the drive Roller, on the opposite side, to ensure an adequate normal force for proper traction. Pixel Short for picture element. The smallest element of a graphic. Platen The hard rubber Roller that drives the media through the Printer, providing support to the backside of the media during printing or laminating. PET Abbreviation

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 303 Image A collection of pictures or graphical elements that compose the visual features on a card. Also refers to the digital representation. Inhibit (panel) The Inhibit or I designation under YMCKI indicates the ability to prevent the transfer of film to the card surface. Users can select these Ribbon types to prevent film from transferring over security features, signature panel or other areas of special interest on the card su

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 17 Agency Listings Term Description Emissions Standards CE, FCC, CRC c1374, EN 55022 Class A, FCC Class A, EN 55024: 1998, EN 61000-3-2 and EN 61000-3-3. Safety Standards UL IEC 60950-1 (2001), CSA C22.2 No. 60950-1-03. United States This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may c

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 287 4 Insert the cleaning card (D900589) into the flipper table slot at a slight angle 5 While holding the cleaning card in place with your fingers, hold the forward button down as the roller spins on the cleaning card. 6 Turn the cleaning card over and perform this same task.

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 214 (Note #1: After making the required selection, the Magnetic Track options box displays the current set of customization options for the selected track.) (Note #2: For most applications, the default settings for these options do not need to be changed.) Using the Character Size buttons Use this option to customize the Character Data Size (Bits per Character) used to encode the magnetic data on the currently selected track. (Note: This character size i

• HID HDPii, HDPii High Definition Card Printer/Encoder User Guide L001130 Rev 1.4 12 12 The Fan turns ON as required to keep head cool. 13 The Ribbon Drives, Film Drive and Print Platen Stepper turn ON and the Printhead burns the image data until the image data is depleted. All stop. (Note: The Ribbon Encoders and Film Encoders are active during this step.) 14 The Headlift Motor engages, moving the Printhead up until the Headlift Sensor is activated. All stop. The Film Drive reverses the Film Positio

Related Products and Documents (Printer):

Comparable Devices:

Similar Resources:

• Xerox Phaser 4600 (2 pages) 35 kg77.2 lb.10.0 cm(3.9 in.)32.0 cm(12.6 in.)130.8 cm(51.5 in.)66.4 cm(26.1 in.)?14 5 62 30:05:0012.12.23 412 3 4ProductInstallationGuideXerox® Phaser® 4600/4620Installation GuideGuide d'installation700N00198 Rev A© 2011 Xerox Corporation. All rights reserved.13284675ItalianoDeutschEspañolPortuguêsNederlandsSvenskaNorskDanskSuomiČeštinaGuida all …

• Xerox Phaser 4 400 (16 pages) Evaluator Guide 1Phaser™ 4400 Laser PrinterEvaluatorGuidePhaser 4400 …

• Muratec MFX-3070 (8 pages) D E P L O Y. D U P L I C AT E . D I G I T I Z E . D E L I V E R .B U S I N E S S - C L A S S D O C U M E N T S O L U T I O N SMFX-3070 / MFX-3090 Quick Product GuideMFX-3070 MFX-3090 …

• Oki ES1624n (24 pages) OKI, OkiLAN ® Oki Electric Industry Company, Ltd. Microsoft, Windows, Internet Explorer ®/™ Microsoft Corporation aux États-Unis et/ou dans d’autres pays. Netscape, Netscape Navigator ® américaines, Netscape Communications Corporation. Novell, NetWare ® Novell Corporation aux États-Unis et/ou dans d’autres pays. PCL ® Hewlett Packard Company. …

• Zebra P110 (2 pages) P110i™and P110m™ Card PrintersIdeal for Customized bank/ATM cards•Employee ID cards•Student and faculty IDs•Access control cards•Membership and loyalty cards•Personalized gift cards•Visitor ID cards•Zebra’s Most Affordable, Single-Sided Card PrintersFor versatility and reliability in a compact frame, look no further t …

• Ricoh Priport HQ9000 (6 pages) Ricoh Corporation Five Dedrick Place, West Caldwell, NJ 07006Ricoh®is a registered trademark of Ricoh Corporation. Windows®and Windows®95/98/Me/NT4.0/2000/XP are registered trademarks of Microsoft Corporation. Macintosh®, Mac®OS and AppleTalk®are registered trademarks of Apple Computer, Inc. Adobe®and PostScript®are registered trademarks of Adobe Sys …

Comments, Questions and Opinions: