GE ZBD1870NSS Installation Instructions Manual

Text of GE ZBD1870NSS User Guide:

• GE ZBD1870NSS, GE Consumer & Industrial Appliances I n s t a l l a t i o n I n s t r u c t i o n s I f you have questions, call 800. 626 .2 000 or visit our website at : www. monogram .com Built-In Dishwashers ZBD1850* ZBD1870 * For ZBD1850 also refer to the instructions provided on the template packed with that model

• IMPORTANT – The dishwasher MUST be installed to allow for future removal from the enclosure if service is required. If you received a damaged dishwasher, you should immediately contact your dealer or builder. Optional Accessories – See the Owner’s Manual for available custom panel kits. READ CAREFULLY. KEEP THESE INSTRUCTIONS. FOR YOUR SAFETY Read and observe all C

• PARTS SUPPLIED: ■ Two #8 Phillips head wood screws, 5/8" long to Two #8 Phillips head wood screws, 5/8" long to secure dishwasher to underside of countertop (in literature package). Installation Preparation TOOLS YOU WILL NEED: ■ Phillips head screwdriver Phillips head screwdriver ■ 5/16" and 1/4" nutdriver

• GE ZBD1870NSS, Installation Preparation PREPARE DISHWASHER ENCLOSURE • The rough cabinet opening must be at least 24" deep, 17-5/8" to 18" wide and approximately 34-1/2" high from fl oor to underside of the countertop. • The dishwasher must be installed so that drain hose is no more than 10’ in length for proper drainage. WARNING To reduce the risk of electric shock, fi re, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation. CLEARANCES: When installed into a corner, allow 2” min. clearance between dishwasher and adjacent cabinet, wall or other appliances. Allow 25-5/8&

• GE ZBD1870NSS, Installation Preparation PREPARE ELECTRICAL WIRING #282 French FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. #282 French The improper connection of the equipment grounding conductor can result in electric shock. Check with a qualified electrician or service representative if you are in doubt that the appliance is properly grounded. Do not modify the plug provided with the appliance; if i

• GE ZBD1870NSS, Installation Instructions PREPARE HOT WATER LINE • The line may enter from either side, rear or fl oor within the shaded area shown in Figure F. • The line may pass through the same hole as the electrical cable and drain hose. Or, cut an additional 1-1/2" dia. hole to accommodate the water line. If power cord with plug is used, water line must not pass through power cord hole. Figure F Water Line Connection • Turn off the water supply. • Install a hand shut-off valve in an accessible location, such as under the sink. (Optional, but strongly recommended and may be required by local codes.) • W

• GE ZBD1870NSS, Installation Instructions Figure I • Lay the dishwasher on its back. Remove the four screws securing the toekick to the dishwasher, and remove the toekick. • Remove the single screw just above and to the side of each front leveling leg. • Remove the side panels and set the dishwasher upright. To adjust the door springs: • Pull the spring adjustment pin out of the holes, insert in the next highest or lowest hole and test again. Figure J Figure K • Adjust both door springs to the same tension. • Continue moving the spring pin until door is balanced. • Replace the dishwas

• GE ZBD1870NSS, 90° Elbow Fill Hose Thread Seal Tape Wa ter Va lve Bracket White Ground Black Check That White, Black and Green Dishwasher Wires Are Threaded Thru Hole in Back Remove Junction Box Cover Insert Power Cord Wires Thru Strain Relief and Tighten Use UL Listed Wire Nuts A C B D Installation Instructions STEP 2 ADJUST LEVELING LEGS • Move the dishwasher close to the installation location and lay it on its back. Figure L • Measure installation height and dishwasher height. Extend leveling legs out from the dishwasher base, 1/2" less than installation h

• Installation Instructions STEP 6 POSITION WATER LINE AND HOUSE WIRING • Position water supply line and house wiring on the fl oor of the opening to avoid interference with base of dishwasher and components under dishwasher. Figure P Figure Q Figure R STEP 7 INSTALL DRAIN HOSE THROUGH CABINET • Stand the dishwasher upright and position in fr

• GE ZBD1870NSS, Countertop Figure S Control Panel Countertop Figure T Dishwasher Door 1/2” Min. Installation Instructions STEP 9 POSITION DISHWASHER UNDER COUNTERTOP • Push the dishwasher into the cabinet. • Push the sides with your hands. Do not use your knee against the door since door damage will occur. • Check that the tub insulation blanket does not get “bunched-up” or interfere with the springs as you slide it into the cabinet. • Center the dishwasher in the opening. • Front of door panel should be fl ush w

• GE ZBD1870NSS, 8 Turn Legs to Adjust Installation Instructions STEP 10 LEVEL DISHWASHER IMPORTANT – Dishwasher must be level for proper dish rack operation and wash performance. • Make sure 1/2" minimum gap is maintained (see Figure T). • Place level on door to check that the dishwasher is level side- to-side. Place level on rack track inside tub to check that the dishwasher is level front-to-back.           �

• GE ZBD1870NSS, Installation Instructions STEP 12 CONNECT WATER SUPPLY Connect water supply line to 90° elbow. • Slide compression nut, then ferrule over end of water line. • Insert water line into 90° elbow. • Slide ferrule against elbow and secure with compression nut. Figure EE Figure FF STEP 13 CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES AND ORDINANCES. The molded end of the drain hose will fit 5/8" through 1" diameter inlet ports on the air gap, waste tee or disposer. • Determine size of inlet port �

• GE ZBD1870NSS, 11 White Ground Black Check That White, Black and Green Dishwasher Wires Are Threaded Thru Hole in Back Remove Junction Box Cover Insert Power Cord Wires Thru Strain Relief and Tighten Use UL Listed Wire Nuts A C B D Installation Instructions STEP 14 CONNECT POWER SUPPLY Skip this step if equipped with power cord. Verify that power is turned off at the source. • Remove junction box cover “A”. • Locate the three dishwasher wires, (white, black and green) with stripped ends. Insert dishwasher wires through the small hole in the junction box “B”. • Secure house wiring to the bottom of the junction box

• GE ZBD1870NSS, Installation Instructions STEP 16 DISHWASHER WET TEST ■ Turn on power supply (or plug power cord into outlet, Turn on power supply (or plug power cord into outlet, if equipped). ■ Start the unit to check for leaks. Start the unit to check for leaks. – Press ON/OFF button to turn unit on – Press CYCLE SELECT button until light below RINSE cycle illuminates ■ Close door. Close door. ■ Check to be sure that water enters the dishwasher. If water Check to be sure that water enters the dishwasher. If water does not enter the dishwasher, check to be sure that water and power are turned on. ■

Related Products and Documents (Dishwasher):

Comparable Devices:

Similar Resources:

• KitchenAid KUDK01TKBT0 (36 pages) I_itchen_kid _UNDERCOUNTER DISHWASHERFor questions about features, operation/performance, parts accessories or service, call: 1-800-422-1230In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...www.kitchenaid.com or www.kitchenaid.com/canadaLAVE-VAISSELLE ENCASTREAu Canada, pour assistance …

• Scandomestic SFO 3502 W (166 pages) –SFO 3502 W Brugermanual User manual Bedienungsanleitung Användarmanual …

• Electrolux ÖKO-FAVORIT 8081 i (12 pages) SERVICE MANUAL© AEG Hausgeräte GmbHMuggenhofer Straße 135D-90429 NürnbergGermanyFax +49 (0)911 323 1420TSE - NAusgabe: 11.98Edition: 11.98Publ.-Nr.:599 50 66 51685DishwasherFully electronic dishwasherFAVORIT 8081ENDISHWASHER …

• Bauknecht GSF 7297 (4 pages) Further indications are given in the pages to follow and in the user instructions.Water supply indicatorCheck the appliance fills with water.Lower spray arm block indicatorRelease the spray arm.“Water stop” device indicator“Water stop” device not working. Switch off the dishwasher and shut off the water tap.Rinse aid level indicatorAdd rinse aid.Salt …

• KitchenAid KUDI011L (19 pages) I_Jtchen_kid ®UNDERCOUNTER DISHWASHERFor questions about features, operation/performance, parts accessories or service, call: 1-800-422-1230In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...www.kitchenaid.com or www.KitchenAid.caPLAVE-VAISSELLE ENCASTREAu Canada, pour assistance compo …

• Metos Master HOOD 130 LUX II (30 pages) Instructions for Use and MaintenanceCOD.: 5250E_U Ed. 01 - 01/2021(15.4.2020)HOOD TYPE DISH WASHERMetos Master HOOD 130 LUX II4246468, 4246468N, 4246469, 4246469N, 4246470. 4246470MK, 4246470MM, 4246470MNManufacturers original documentation …

Comments, Questions and Opinions: