Manualios.com

Century Helicopter Products Raven 30 V2 Instruction Manual

Century Helicopter Products Raven 30 V2 Manual Online:

4.7, 827 votes
Century Helicopter Products Raven 30 V2 User Manual
Century Helicopter Products Raven 30 V2 User Guide
Century Helicopter Products Raven 30 V2 Online Manual

Text of Century Helicopter Products Raven 30 V2 User Guide:

  • Head Block M3x20 Socket Cap Screw & M3 Locknut Washout & Swashplate Assembly from Step 6 Step 24 Final Rotor Head Assembly Following assembly, move the swashplate up and down to the endpoints. The swashplate and washout unit should be very smooth throughout the movement range. If not, inspect the fit of the washout guide to the pins in the rotor head, these pins can be bent s

  • 11 Step 11B Torque Drive Pinion Gear From parts bag 2: Using threadlock, insert one M3x4 Set Screw (Tip 1) into the gear, note where the flat spot is on the shaft and slide the gear on and tighten (make sure the set screw is positioned over the flat spot) the set screw. Slide two Ball Bearings onto the shaft and install into one half of the upper frames. Next add the spacer, apply threadl

  • Century Helicopter Products Raven 30 V2, 7 From parts bag 1: Iznsert the Feathering Shaft into the head block, slide one M6X10 Washer on each side of the shaft. Install the blade grip ( Note the direction of the bell mixer arm ) followed by one M8x13 Washer, one M6x12 Thrust Ball Bearing ( install the first steel washer (large inside diameter) followed by the ball race, remember to grease the ball race, followed by the second steel washer (smaller inside diameter) and one M5 Locknut. Tighten the locknut, using the glow plug socket wrench on one nut while holding the other with pliers, tighten the nuts until both blade grips turn freely without any excessive

  • Century Helicopter Products Raven 30 V2, From parts bag 2: Assemble the Constan Tail Drive Gear Assembly (R50), start by pressing the shaft through the Counter Gear then selide two M5x7x2 spacers, then slide the two M5x13 Ball Bearings. Again slide two M5x7x2 spacers onto the shaft and slide the Alloy Drive Gear onto the shaft aligning the flat spot on the shaft. Insert one M4x4 set screw (Tip1) into the Alloy Drive Gear and tighten in place. Alloy Drive Gear 14T (SE50) [CN2224] M5x7x2 Spacer x 2 5x13 Ball Bearings x 2 [CNBB1350] Drive Shaft [CN2263D] Counter Gear 55T [CN2263C] Counter Gear 53T (Option 3D Hi-Spd) [CN2263F] M

  • Century Helicopter Products Raven 30 V2, Position the rear servo mount bracket on the left side of the mechanics just behind the main shaft, the front of the mount has a right angle knotch beside the hole. Insert one 3x10mm Socket Cap Screw through the servo mount and into the upper side frames with one 3mm Locknut to secure in place. Insert one 3x25mm Socket Cap Screw and match the 3mm Locknut into the molded hole for the locknut in the upper frames. At this time install the remaining 3x25mm Socket Cap Screw and 3mm Locknut into the rear-most hole in the upper f

  • Century Helicopter Products Raven 30 V2, 19 From parts bag 5, assemble the servo tray using four 3x12mm Self Tapping Screws (Tip 3) into the lower holes of the battery tray. Next install the throttle servo from the inside of the left vertical support in the lower position. ( Note, use the rubber grommets provided with the servos, you can use the screws that came with your servos or the screws provided in the kit ). Notice that the output shaft of the servo is towards the front. Insert the servo screws from servo frame side through the slots and secure using the servo mount tabs pro- vided. Using two 3x10mm Socket Cap Screws, attach the long hex spacer to the front-most up

  • Century Helicopter Products Raven 30 V2, 9 Starting with the inside race, apply threadlock and attach two short balls (Tip 1) directly across from each other, similarly attach two medium balls to the remaining holes. Attach three short balls (Tip 2) to the outside race, each 120 degrees apart. The extra location is used for the anti- rotation bracket assembled later. Step 8 Swashplate Assembly Before starting, carefully apply two or three drops of CA to the seam between the top and bottom oilite bushings and the plastic washout hub. Do not get

  • Century Helicopter Products Raven 30 V2, From parts bag 2: The Start Shaft Guide Blocks are pre-assembled. Slide the Starter Shaft through one of the block assem- blies with the M5x11 Ball Bearing facing up then slide the M5 Flat Washer, spring and finally the M5x10 Collar. M5x10 Collar M2x5 Self Tapping Screw Spring M2x5 Flat Washer 5x11 Ball Bearing x 2 [CNBB1150] Start Shaft Guide Blocks x 2 [HI3007] Starter Shaft Set [HW3005A] Step 9 Starting Shaft Bearing Blocks Step 10 Starting Shaft & Hex Coupler From parts in bag 2: After sliding the top bear- ing block in place, attach the hex starter adapter CN0402 to the starting shaft using threadlock on both 4x4mm set screws. Align one

  • Century Helicopter Products Raven 30 V2, 4 Necessary Items “Not Included” in the kit 6 Channel Helicopter Radio or Equivalent. Glow Remote Adapter CN2222 32-40Helicopter Engine 50 Helicopter Engine Tuned Muffler 30 size CN3033 Tuned Muffler 46 size CN3033B Necessary Tools for Assembly and Adjustments Main Blade Pitch Gauge w/PaddleGauge CN2026 Ball Link Plier CN2034 15% or 30% Heli Fuel 12Volt Start Battery 12Volt Starter Fuel Line Eletric Fuel Pump or Hand Pump Glow Starter w/Charger 5.5mm,7mm, Phillips Screw Driver 4 Way Wrench CN2031 Hobby Scissors Allen Key Set CNBN10946 Hobby Knife Metric Ruler Locktite Servo Tape Lubrication CN2024T Tie-Wraps Fuel Filter Glow Plug Whip Antenna Needle Nos

  • Century Helicopter Products Raven 30 V2, 35mm 21 From parts bag 6, assemble the landing gear by attaching the Aluminum Skids through the Struts, securing them with four 3x5mm Set Screws. Set the distance from the rear of the skid to the strut at 35mm. Attach the landing gear to the main mechanics using four 3x16mm(30) or 3x20mm(50) Machine Screws inserted from the bottom of the struts and through the M3x9 plastic spacers into the lower side frames and secure with four M3 locknuts. Plastic Struts - 30 [HI3122] x 2 M3x5SS Set Screws x

  • Century Helicopter Products Raven 30 V2, 3 Building Instructions for the Raven eCCPM helicopter kits. Introduction Congratulations on your purchase of Century Helicopter Product's newest RC helicopter model. The Raven eCCPM is a new breed of helicopter, ideal for beginners new to the hobby through to expert pilots. In order for our helicopters to improve, we needed to provide higher value for a better price, but this needed revising. Our result is this kit you are about to start building, offering the best design and quality of the 30 and 50 class and including features commonly foun

  • Century Helicopter Products Raven 30 V2, Raven 30/50 V2 Instruction Manual R30 R50 DD DD D MAIN ROTOR 550mm 600mm DD DD D TAIL ROTOR DIAMETER 9.7 in 9.7 in DD DD D OVERALL LENGTH 46 in 47.5 in DD DD D HEIGHT 15 in 15 in DD DD D BLADES 550mm 600mm DD DD D ENGINE 32 ~ 40 50 Century Helicopter Products Designed and Developed in USA 3rd Edition, Copyright June 2006. All rights reserved. SPECIFICATIONS 2oz Header Tank w/ CNC Machined Mount or Die- cut Mount CN2137 CN2213 Machined Mount CN2137 Die Cut Mount Aluminum Turbo Cooling Fan Increased 15% air flow, lower engine drag and smoother high speed operation. CN2202A Turbo cooling fan o

  • Century Helicopter Products Raven 30 V2, Step 20 Fuel Tank Assembly From parts bag 3, insert the two pieces of aluminum tubing through the large cap, rubber stopper and small cap, bend the long aluminum tube upwards and attach the short piece of fuel line and clunk to the short straight piece of tubing. Test fit the assembly into the Fuel Tank and make sure that the clunk reaches the end but moves freely and the vent tube is near the top of the tank but does not touch. Finally tighten the long self tapping screw to seal the tank. Install the included tie

  • Century Helicopter Products Raven 30 V2, STEP 5 Flybar Control Arm Assembly From parts bag 1: Using an available M3x12 Button Head Screw, insert ap- proximately half the length of the screw to form threads into the smaller, tapered ends of the control arms and the control arm stand-offs. Assemble Pushrod A (47mm center to center) and press one ball link end onto each double studded steel ball, making sure that pressure is applied from the side of the ball link with the Century name. All ball links are designed to be installed in one direction only. While holding one flybar contr

  • Century Helicopter Products Raven 30 V2, 13 The Main Gear is pre-assembled with the Auto-Rotation Bearing installed. From parts bag 2: The Main Shaft has a step in the end of the shaft that is inserted through the auto-rotation assembly. Insert the bottom end through the auto rotation gear assembly aligning the holes and secure the Main Shaft using one 3x16mm Socket Cap Screw and one 3mm Locknut. Main Gear [HI3056] Main Shaft [HW3053A] M3x16 Socket Cap Screw M3 Locknut Auto- Rotation Bearing [HW3040] Pre- Assembled Step 13 Main Gear Assembly R30 Step 14 Slipper Assembly - R30 Optional only (Onl

  • 5 This manual has been written for both the Raven 30 and 50 helicopter. CN1060 Raven 30 kit and CN1061 raven 50 kit. The main portion of the manual covers the full construction of both kits with labeling for both 30 & 50 respectively. Every attempt has been made to ease the assembly of your kit, at each step where there are complex instructions there are detailed written ins

  • Century Helicopter Products Raven 30 V2, Tail Transmission Output Gear Assembly from Step 11 - Counter Gear Assembly from Step 12 Upper Side Frame [HI3107] Main Gear Assembly from Step 13 M3x12 Self Tapping Screws x 4 M4x4 Set Screw (med hex key) x 2 Mast Stopper [HW3054A] 8x19 Ball Bearing [CNBB1980] Start Shaft Assembly from Step 10 Note 1: Be careful when tightening the eight 3x12mm self tapping screws into the start shaft block assemblies as excessive force will strip out the plastic holes. 10x19 Ball Bearing [CNBB1019] M14x19 Washer CCPM Right Side Servo Mount [HW3115B] From parts bag 2: Install two 4x4mm Set Screws (do not apply locktight at this time) in the Mast Stop- per (note the raise

  • Century Helicopter Products Raven 30 V2, 15 Long hex spacers [HW3127A] x 2 M3x35 Socket Cap Screws x 4 M3 Locknut x 4 Insert two long Hex Spacers at the specified locations in the diagram, note that the front hex spacer is installed into the forward-most hole. Attach the left side CCPM Servo Mount using four M3x12 Self Tap- ping Screws (Tip3) into the starting shaft blocks. Install the upper left side frame, taking care that the bearings are aligned with the mating recesses and secure the frames with four M3x35 Socket Cap Screws (Tip1) through the main shaft bearing block positions and four M3 locknuts. While pushin

  • Century Helicopter Products Raven 30 V2, 2 Table of Contents Table of Contents .......................................................................................................................................... 2 Introduction .................................................................................................................................................. 3 Required Items for Assembly ....................................................................................................................... 4 Building Guide for Raven 30 & 50 kits ..................................................................................................... 5 Main Rotor Head & Seesaw Asse

  • Century Helicopter Products Raven 30 V2, 17 Step 18 Clutch, Fan & Engine Mounting Clutch Shoes [HW3011] M9x14 Flat Washer Engine ball bearing exposed. Thrust Washer or M9x14 FW From parts bag 3, remove all parts from the engine crankshaft until you can see the front ball bearing, install the 9x14mm Flat washer (or washer provided by engine manufacturer), insert the Ball Bearings into the clutch bell assembly and place on the crankshaft. Clean the threads (Tip 1) on the crankshaft, engine nut and the clutch, carefully apply threadlock on the engine crankshaft threads nearest the bearing (be careful not to get threadlock into the ball bearings) and on the threads in the clutch.

  • Century Helicopter Products Raven 30 V2, Tail Pitch Ball Links x 2 M2x8 Pin x 2 [HI3089] From parts bag 7: The Tail Pitch Plate and Tail Pitch Ball Links are pre-assembled. (Note: apply some JB weld to the outside of the lock ring to avoid the assembly loosening.) Apply a drop of CA glue between the edge of the brass tube and the plastic pitch plage. Put this assembly aside for now. Tail Pitch Plate [HI3087A] Pre-Assembled Step 28 Tail Pitch Plate Assembly 6x10 Ball Bearing x 2 [CNBB1060] 5x13 Ball Bearing x 2 [CNBB1350] Tail Gearbox Input Shaft [HW3070A] 2x12mm Pin M3x4 Set Screw (small he

Related Products and Documents (Toy):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Oki B6250 Operation & user’s manual oki/b6250-66N.pdf 08 Aug 2023 55
2 Red Hat CLUSTER SUITE FOR ENTERPRISE LINUX 5.2 Management manual red-hat/cluster-suite-for-enterprise-linux-5-2-8P1.pdf 19 Aug 2022 36 0.38 Mb
3 Siemens FDOOTC241 Technical manual siemens/fdootc241-Z2I.pdf 07 Jul 2022 84
4 Moffat GSC5050W Operating & installation instructions manual moffat/gsc5050w-BAN.pdf 01 Sep 2023 27
5 Dynex DX-CMBOSLM - Slim USB 2.0 CDRW/DVD Combo Drive Operation & user’s manual dynex/dx-cmboslm-slim-usb-2-0-cdrw-dvd-combo-drive-CNY.pdf 12 Mar 2023 20 1.45 Mb
6 BenQ G2420HDB Operation & user’s manual benq/g2420hdb-C58.pdf 30 Dec 2022 29 0.98 Mb

Similar Resources:

  • Faller

    HORREM

    (28 pages)
    BAHNHOF »HORREM«»HORREM« STATION GARE DE »HORREM« STATION »HORREM«Art. Nr. 110130Sa. Nr. 110 130 1Inhalt Spritzlinge Contents Sprues Contenu Moulages Inhoud Gietstukken7 A I1x7 A II1x7 A III1x7 A IV3x7 B2x7 AC I1x7 C1x8 A1x81x131x141x91x101x121xInhalt Spritzlinge Contents Sprues Contenu Moulages Inhoud Gietstukken1 B1x1 B1x2 A1x2 B1x3ABCX1x3ABCY1x4 C …
  • QOLSYS

    IQ PANEL

    (32 pages)
    ABOUT THIS DOCUMENTThis document describes the user interface and controls for the Qolsys IQ Panel, a “Smart home” control and automation system. Within these pages you will find how to enable and simplify home security, home control, energy management, home healthcare, and other services. The IQ Panel uses wireless technology to communicate with a broa …
  • Eduard

    32 321

    (2 pages)
    1215143738M31, M34M32, M331/2B-25 bomb bay 32 32132 3211/32 scale detail set for kit • sada detailù pro model HK Models 1/32 HK ModelsORIGINAL KIT PARTSPÙVODNÍ DÍLY STAVEBNICEPHOTO-ETCHED PARTSLEPTANÉ DÍLYPARTS TO BE REMOVEDDÍLY K ODSTRANÌNÍFILLTMELITeduardREMOVEODSTRANITOPTIONVOLBA?REPLACENAHRADITBENDOHNOUTGRINDOBROUSITSYMETRICAL ASSEMBLYSYMETR …
  • BLOTZ

    B28-VSF-010

    (3 pages)
    28mm VSF Deck Gun B28-VSF-010 Please read these instructions fully before starting construction. PVA or equivalent glue will be required to stick sections together. Sand paper can be used to gently clean any joints. A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember to cut away from you …
  • Phoenix Model

    Rainbow

    (12 pages)
    AIR FRAME ASSEMBLIES. (2) Wing halves with ailerons. (1) Fuselage. (1) Horizontal stabilizer with elevator halves. (1) Vertical stabilizer with rudder. (1) Cowling. (1) Decal sheet. (1) Instruction manualMAIN GEAR ASSEMBLY. (2) Main gears. (2) 60mm diameter wheels. (4) Wheel collars. (2) Wheel pants and accessories. (4) 4mm x 15mm sc …
  • Fisher-Price

    77961

    (12 pages)
    G InstructionsProduct Number: 77961F Mode d’emploiRéférence du produit : 77961D AnleitungArtikelnummer: 77961N GebruiksaanwijzingArtikelnummer: 77961I IstruzioniNumero Prodotto: 77961E InstruccionesNúmero de referencia: 77961KBrugsanvisningProduktnummer: 77961P InstruçõesReferência do Produto: 77961TOhjeetTuote numero: 77961M BruksanvisningProduktnum …

Comments, Questions and Opinions: