Black Line BLK-CPD700 Operation & User’s Manual
|
Black Line BLK-CPD700, 2 Focus adjustZoom adjust Rotate lock screw Rotate ring Pan lock screw (4) OSD control board Drop cable video, power, connectors Video test port BLK-CPD700R camera module back 1.1.1 What’s in the box Your camera includes the following: • Camera assembly • Four (4) coarse-threaded screws and wall inserts to secure the base to the mounting surface • Torx® (T-20) L-wrench for removing the dome (BLK-CPV700 series only) • Power adapter cable (with female plug) for power drop cable • Video test port to BNC adapter cable • Screw driver • This manual 1.1.2 Tools you need To install the cam
21 High Performance 700TVL CCTV Dome Camera User Manual SECTION 3: SOFTWARE SETUP MIRROR (o) MIRROR D-EFFECT selected D-ZOOM: D-ZOOM allows you to zoom in on a portion of the image by rst setting the digital zoom magnication (x1 ~ x32), and then using the PAN and TILT controls to move to the area of the image you want to see. When D-ZOOM is used,
1 High Performance 700TVL CCTV Dome Camera User Manual SECTION 1: INTRODUCTION SECTION 1 Introduction These high performance CCTV dome cameras feature a very high resolution Sony ® CCD sensor providing 700 TVL, dual voltage range (24 Vac, 12 Vdc), and on-screen display (OSD) for control and setup. The BLK-CPV700 and BLK-CPV700R cameras feature a vandal-pro
Black Line BLK-CPD700, BLK-CP700 Series High Performance 700TVL Varifocal CCTV Dome Cameras User Manual Products: BLK-CPD700, BLK-CPD700R, BLK-CPV700, BLK-CPV700R BLK-CPD700 and BLK-CPV700R Please read this manual before using your camera, and always follow the instructions for safety and proper use. Save this manual for future reference. BLK-CPD700-CPV700_CM 2/17/14
Black Line BLK-CPD700, 8 SECTION 2: INSTALLATION 2. Remove the dome from the camera by loosing the four captive dome screws using the Torx L-wrench provided (BLK-CPV700 series) or inserting a coin into the slot on the side of the camera to pry it o (BLK-CPD700 series). 3. Remove the camera module from the base by loosing the three captive screws that secure the camera module to the base. 4. If you are installing a BLK-CPV700 series camera, position the base seal appropriately onto the base. 5. Route the camera drop cable through the hole in the center of the base, then through the body of the mounting bracket. NOTE Drop cable connect
Black Line BLK-CPD700, 5 High Performance 700TVL CCTV Dome Camera User Manual SECTION 2: INSTALLATION 1. Remove the camera dome cover from the camera. If you have a BLK-CPD700 series camera, use a coin to pry o the cover. For BLK-CPV cameras, loosen the four captive dome screws using the Torx L-wrench provided. 2. Remove the camera module from the base by loosing the three captive screws that secure the camera module to the base. 3. Determine (and acquire, if needed) the best type of fasteners for attaching the camera to the mounting surface. The mounting screws and wall inserts provided are adequate for most surfaces. 4. Using the camera base as a guide, mark the location of the screws that a
Black Line BLK-CPD700, 14 SECTION 3: SOFTWARE SETUP — After selecting the AREA graphical submenu, a POSITION screen opens. Rock the joystick up, down, left and/ or right to position the upper-left corner of the BLC area, then push the joystick in to conrm your selection and enter the SIZE graphical submenu. — In the SIZE graphical submenu, rock the joystick up or down to raise or lower the bottom edge of the AREA. Rock the joystick left and/or right to contract or expand the AREA horizontally. — Press the joystick in twice to return to the BLC menu. DEFAULT: Select DEFAULT to revert to the default AREA position and size. RETURN: Select RETURN to return to the EXPOSURE submenu. HSB
Black Line BLK-CPD700, 10 SECTION 2: INSTALLATION b. Lift the camera head slightly away from the base and turn it to the direction of your surveillance target. NOTE: If any resistance is felt when turning the camera head, loosen the lock screws until the camera head turns freely. You can turn the camera head up to 360° left or right. Tighten the pan lock screws until snug to hold the camera head in place. Tilt adjustment (image up or down) Pan adjustment (image left or right) 3. Tilt adjustment (moves video up or down): Rotate the camera about the gimbal axis to center your surveillance target in the video image.
26 SECTION 3: SOFTWARE SETUP FACTORY: Select FACTORY to reset the camera conguration. RETURN: Rock the joystick to select RETURN, to return to the SETUP menu. 3.9 EXIT Select EXIT to close the SETUP menu.
Black Line BLK-CPD700, 15 High Performance 700TVL CCTV Dome Camera User Manual SECTION 3: SOFTWARE SETUP DWDR OFF DWDR ON OFF: The D-WDR function is disabled. INDOOR: The D-WDR is preset with default LOW-LEVEL and HIGH-LEVEL settings for normal indoor lighting condition. These settings can be adjusted in the INDOOR sub-menu. RETURN: Select RET to return to the EXPOSURE menu. OUTDOOR: The D-WDR is preset with default LOW-LEVEL and HIGH-LEVEL settings for normal outdoor lighting condition. These settings can be adjusted in the OUTDOOR sub-menu. RETUR
Black Line BLK-CPD700, 19 High Performance 700TVL CCTV Dome Camera User Manual SECTION 3: SOFTWARE SETUP ON: Activates the noise reduction feature. Selecting this option opens the 3DNR sub-menu where the level of noise reduction can be adjusted. LEVEL: With the cursor pointed at the LEVEL, rock the joystick left or right to decrease or increase the level of noise reduction. The default setting is 200 (maximum). RETURN: Select RET to return to the SETUP menu, or END to close the SETUP menu. 3.6 SPECIAL Selecting SPECIAL opens a feature list of special camera functions. CAM TITLE: This feature will display a user de
Black Line BLK-CPD700, iii High Performance 700TVL CCTV Dome Camera User Manual Table of Contents SECTION 1 Introduction .......................................................................1 1.1 Features ............................................................................1 1.1.1 What’s in the box ................................................................2 1.1.2 Tools you need ..................................................................2 1.1.3 Optional mounting brackets .......................................................3 SECT
Black Line BLK-CPD700, 6 SECTION 2: INSTALLATION Screw locations for surface mount Hole in side for drop cable (conduit) Hole in base for drop cable (conduit) Screw locations for bracket mount Cable channel (between base and seal) BLK-CPV700 series camera base 5. Drill holes for the screws that anchor the base to the mounting surface. The four (4) course-threaded screws and wall inserts provided are sucient for mounting the camera to most surfaces. However, other fasteners may be more appropriate. 6. Drill a 3/4” hole through the mounting surface for the drop cable, if necessary. 7. Route the camera drop cable through the base as planned. 8. If you are installing a B
29 High Performance 700TVL CCTV Dome Camera User Manual SECTION 5: SPECIFICATIONS Model BLK-CPD700 BLK-CPD700R BLK-CPV700 BLK-CPV700R Lens DC Auto iris varifocal lens (2.8 ~ 12 mm) Operational Temperature 14 °F ~ 122 °F (-10 °C ~ 50 °C), RH 95% max. Storage Temperature -4 °F ~ 142 °F (-20 °C ~ 60 °C), RH 95% Max. Dimension (W x H x D) 5.91" x 4.72" x 5
Black Line BLK-CPD700, 11 High Performance 700TVL CCTV Dome Camera User Manual SECTION 3: SOFTWARE SETUP SECTION 3 Software Setup The OSD (On Screen Display) software setup menus can be viewed from the camera video output or through the VIDEO TEST port on the OSD Control board. The OSD control board is accessible when the camera dome is remove. Conguration settings are made using the OSD joystick (see photo below). Video test port OSD joystick OSD control board Use the SETUP joy stick on the OSD control panel to na
Black Line BLK-CPD700, 22 SECTION 3: SOFTWARE SETUP NEG. IMAGE: Set this option to ON to show a color-reversed or black and white-reversed image. RETURN: On the D-EFFECT menu, select RETURN to return to the SPECIAL menu. MOTION: The MOTION feature allows you to quickly identify areas of the image where motion is detected. Set MOTION to ON then press the joystick in to open the MOTION sub-menu. You can congure up to four motion detect areas on the image. AREA: Move the cursor to AREA, then rock the joystick right or left to select 1, 2, 3, or 4. The area selected will blink in the background. AREA DISPLAY: Move the cursor to AREA DISPLAY, then rock the joystick right or left to select ON to congu
Black Line BLK-CPD700, 16 SECTION 3: SOFTWARE SETUP AWC g SET: With this setting, focus the camera on white paper, then press the joystick in to set the white balance to ambient lighting conditions. If the environment and/or light source changes, the white balance should be re-adjusted. MANUAL: This option is used to make ne adjustments to the white balance setting. To use this option: — Set the white balance using ATW or AWC. — Select MANUAL. Rock the joystick right and/or left to Increase or decrease the value of BLUE (B-gain) or RED (R-gain) while monitoring the color of the i
Black Line BLK-CPD700, 4 SECTION 2: INSTALLATION SECTION 2 Installation 2.1 General Guidelines • Camera Lens: Handle the camera dome carefully to prevent scratching or soiling the dome and lens. If the dome or lens becomes soiled, clean it only with approved products. See the Cleaning section later in this manual. • Monitor impedance: Set the monitor impedance switch to 75Ω. • Power supply: To avoid re or shock hazard, use only a UL listed power supply. • Camera drop cable: The camera drop cable includes two connectors: — Power connector (blu
Black Line BLK-CPD700, 17 High Performance 700TVL CCTV Dome Camera User Manual SECTION 3: SOFTWARE SETUP B/W: The picture is displayed in black and white only. When B/W is used, WHITE BAL is disabled. Selecting this option opens the B/W sub-menu. BURST: Burst ON sends a color signal to the monitor in B/W mode. This signal does degrade the clarity of the image from the camera. Some DVRs require a color burst signal to detect the camera. IR SMART: This option controls the IR LED output level to compensate for object distance. IR SMART is applied to objects in a speci
Black Line BLK-CPD700, 7 High Performance 700TVL CCTV Dome Camera User Manual SECTION 2: INSTALLATION CAUTION When using 12 Vdc powering, use extreme caution to observe the polarity of the of the voltage applied to the camera. The camera power drop cable connector center lead should receive +12 Vdc when measured to the shield (ground). NOTE Drop cable connectors are not waterproof. 12. Attach the far end of the video extension cable to video monitoring equipment such as a DVR. 13. Attach the far end of the power extension cable to a 12 Vdc or 24 Vac power source. 14. Apply power to the camera. Verify that video
13 High Performance 700TVL CCTV Dome Camera User Manual SECTION 3: SOFTWARE SETUP NOTE The SENSE-UP feature is only available when the SHUTTER option is set to AUTO or 1/60 (DC LENS). When SENSE-UP is activated, the increased magnication can induce noise and pixilation. SENSE-UP: Rock the joystick left or right to observe the optimal screen brightness in low li
Black Line BLK-CPD700, 23 High Performance 700TVL CCTV Dome Camera User Manual SECTION 3: SOFTWARE SETUP — ON: When motion is detected, the motion detection areas where motion is detected are highlighted. RETURN: Select RETURN to return to the SPECIAL menu. PRIVACY: The PRIVACY feature allows you to block up to 8 areas of the image from being seen. The areas blocked are covered by a color-coded polygonal (3-, 4-, or 5-sided) shape. Set PRIVACY to ON then press the joystick in to open the PRIVACY sub-menu. AREA: Set the cursor on AREA, then rock the joystick right or left to select any area 1 .. 8. These 8 areas can be individually enabled or disa
Black Line BLK-CPD700, 25 High Performance 700TVL CCTV Dome Camera User Manual SECTION 3: SOFTWARE SETUP SHARPNESS: With the cursor pointing at SHARPNESS, rock the joystick right or left as necessary to produce the clearest image from your camera. MONITOR: Rock the joystick right or left to select the monitor type you using (LCD or CRT), or select USER. The monitor feature enables you to setup your camera to produce the best image for the monitor you use. Rock the joystick left or right to select either LCD, CRT or USER. In the monitor type sub-menu, adjust the settings for each parameter to produce the preferred image. RETURN:
Black Line BLK-CPD700, 3 High Performance 700TVL CCTV Dome Camera User Manual 1.1.3 Optional mounting brackets Two optional mounting brackets are available for the BLK-CP700 series cameras: • BLK-WALLMT: Wall mount bracket • BLK-PENDMT: Pendant mount bracket BLK-WALLMT bracket BLK-PENDMT bracket SECTION 1: INTRODUCTION
Black Line BLK-CPD700, 28 SECTION 5: SPECIFICATIONS SECTION 5 Specications Table 1. Component Specications Model BLK-CPD700 BLK-CPD700R BLK-CPV700 BLK-CPV700R Image Pick-Up Device 1/3” Sony 960H CCD TV System NTSC Total Pixels NTSC = 1020(H) * 508(V) Eective Pixels NTSC = 976(H) * 494(V) Scanning System 2:1 Interlace Synchronization Internal OSD (On screen display) Available Backlight OFF / HSBLC / BLC Selectable Resolution 700 TV Lines S/N (Y signal) 52 dB Minimum Illumination 0.00001 Lux (Sens-up*256) 0 Lux (IR LED on) 0.00001 Lux (Sens-up*256) 0 Lux (IR LED on) White Balance ATW / AWB / Manual / AWC >SET Electronic Sh
AG Electronica PTZ-942L Security Camera Instruction manual
PTZ-942L |
Vivotek IP8152 Security Camera Quick installation manual
IP8152 |
American Dynamics SpeedDome Optima LT Security Camera Brochure & specs
SpeedDome Optima LT |
Clover CM105H Security Camera User instructions
CM105H |
ENFORCER EV-1186-N3GQ Security Camera Manual
EV-1186-N3GQ |
Avue AV819SC Security Camera Manual
AV819SC |
Vista ViP2 VK2-1080VFD Security Camera Installation and user manual
ViP2 VK2-1080VFD |
Panasonic BB-HGW700A - Network Camera Router Security Camera Operating instructions manual
BB-HGW700A - Network Camera Router |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | JVC | SP-AD50-B | Instruction manual | jvc/sp-ad50-b-H24.pdf | 24 Aug 2023 | 28 | |
2 | Vision | ZS 5101 EU | Installation & operation manual | vision/zs-5101-eu-Y7R.pdf | 08 Nov 2022 | 2 | 0.33 Mb |
3 | Tangent | Medix 1500 | Datasheet | tangent/medix-1500-8YJ.pdf | 14 Aug 2023 | 1 | 0.25 Mb |
4 | Craftsman | 919.679370 | Owner's manual | craftsman/919-679370-692.pdf | 21 Sep 2022 | 38 | 0.79 Mb |
5 | SHOWTEC | GALACTIC BEAM G40 V1 | Manual | showtec/galactic-beam-g40-v1-8CN.pdf | 02 Aug 2022 | 28 | |
6 | Lennox Hearth Products | STRIKER C160 | Installation and operation manual | lennox-hearth-products/striker-c160-B67.pdf | 06 Nov 2022 | 18 |
Canon
Network Camera/ / /Installation GuideBIE-7029-001Thank you for purchasing a Canon Network Camera (hereafter referred to as the camera).VB-H630D/VB-M620D is designed for indoor use only. It is also possible to install the VB-H630VE/VB-M620VE outdoors, such as underneath eaves.Be sure to read “Installation Guide” (this document) and “Operation Guide” ( …
VB-H630d(2 pages) |
Velleman
CAMSET27 BUILD-IN BACKING CAMERA WITH COLOUR DISPLAY ACHTERUITRIJDCAMERA MET KLEURENDISPLAY CAMÉRA DE RECUL AVEC AFFICHEUR COULEUR CÁMARA DE APARCAMIENTO CON PANTALLA A COLOR RÜCKFAHRKAMERA MIT FARBDISPLAY USER MANUAL 3GEBRUIKERSHANDLEIDING 5NOTICE D’EMPLOI 8MANUAL DEL USUARIO 10BEDIENUNGSANLEITUNG 13
…
CAMSET27(19 pages) |
Panasonic
1Installation GuideNetwork Camera (PoE Ready)• This manual is written for both the BB-HCM527 (Indoor Use Only) and the BB-HCM547 (Outdoor Ready). Available features and operations vary slightly depending on the model. You can confirm the model no. of your camera by checking the model no. printed on the front of the camera.• Model number suffixes (“A” …
BB-HCM527(4 pages) |
AVer
CAM520 Pro2 Conference Camera Quick Start Guide |安裝指南 安装指南|取扱説明書 빠른 가이드| Mode d'emploi Manual de instrucciones|Краткое руководство
…
CAM520 Pro2(79 pages) |
Strong
HELO CAMERA-W-OUTFull HD Outdoor Security CameraQuick Start GuideSchnellstartanleitungGuide d’Installa on rapideGuida rapida d’installazioneGuía de inicio rápidoGuia de início rápidoSnelstartgidsQuick Start GuideSnabbstartsguidePrůvodce rychlým používánímPríručka pre rýchle spustenieVodič za brzi početak upotrebeКратко ръков� …
HELO CAMERA-W-OUT(164 pages) |
Black
BLK-CPV700RH High Performance 700TVL Extended Temperature Range Vandal-proof CCTV Dome Camera User ManualProducts: BLK-CPV700RHBLK-CPV700RH cameraPlease read this manual before using your camera, and always follow the instructions for safety and proper use. Save this manual for future reference. BLK-CPV700RH_CM 12/9/13
…
BLK-CPV700RH(22 pages) |
Gourmia Ice Cream Maker GSI-400User Manual: Gourmia GSI-400 (9U72HD, Upd.20/11/2023) GSI-400, 16 |
Schenker Laptop XMG U726#328BIW: XMG U726 Laptop Operation & user’s manual XMG U726, 312 |
TRENDnet Network Router TEW-718BRMTEW-718BRM (Network Router ePDF Guide, #YT3V87) TEW-718BRM, 4 |
Kettler Fitness Electronics SM 9150-75Kettler SM 9150-75 Guide (Doc Type: Fitness Electronics Training and operating instructions) SM 9150-75, 22 |
Woodbridge Fireplace Inc Indoor Fireplace BDV2000NEWoodbridge Fireplace Inc BDV2000NE Indoor Fireplace Installation and operating instructions manual BDV2000NE, 52 |
Electrolux Freezer ER 1825 DER 1825 D (Freezer ePDF Manual, #CG5M49) ER 1825 D, 20 |
Jeep Automobile 2012 WranglerOwner's manual for Jeep 2012 Wrangler Automobile 2012 Wrangler, 611 |
Sharper Image Security Camera SI513Instructions manual for Sharper Image SI513 Security Camera SI513, 9 |
Andersson Wireless Router WSR 2.0Andersson WSR 2.0 User Manual (Doc Type: Wireless Router Operation & user’s manual) WSR 2.0, 47 |
Brinkmann Grill 27002700 Owner's manual - ZE7Z89 2700, 32 |
Philips Home Theater System HTD3510Operation & user’s manual for Philips HTD3510 Home Theater System HTD3510, 32 |
Lenovo Desktop ThinkStation E31Lenovo Desktop ThinkStation E31 Operation & user’s manual ThinkStation E31, 158 |