Blackmagicdesign SmartView Duo Installation And Operation Manual

Text of Blackmagicdesign SmartView Duo User Guide:

• Blackmagicdesign SmartView Duo, Developer Information 31 Changing Networking Settings The network can be configured to use either DHCP or a static configuration. To enable DHCP: NETWORK:↵ Dynamic IP: true↵ ↵ To set a fixed IP address, supply all static parameters, thus: NETWORK:↵ Dynamic IP: false↵ Static address: 192.168.2.2↵ Static netmask: 255.255.255.0↵ Static gateway: 192.168.2.1↵ ↵ The parameters with the CURRENT prefix are read-only, and show the active configuration, regardless of the static or dynamic setting. Changing the device name, or any network settings, will cause the IP connection to be dropped. The device will

• Blackmagicdesign SmartView Duo, Getting Started 18 Configuring Blackmagic SmartView Utility Software After installing the Blackmagic SmartView Utility software, launch the Blackmagic SmartView Utility and it should immediately search your network for any SmartView units by using the Bonjour service discovery protocol. Any discovered units will be listed in the SmartView Monitors pane with an Ethernet network icon next to their name. Select the name of the desired SmartView and you will be able to change the device name and also the monitor settin

• Blackmagicdesign SmartView Duo, Getting Started 5 A tally connector is provided for use with switcher and automation systems. The 9-pin D connector wiring description is printed on the rear of the unit showing contact closures to display red, green or blue tally borders on each, independent monitor. If SmartView is to be installed high up in an equipment rack, you may wish to physically invert the LCDs for the optimum viewing angle. The images on the LCDs will automatically flip to the correct orientation when they sense an inversion. A number 02 size Pozidriv screwdriver is required to disconnect and reconnect the faceplate from its rear assembly.

• Blackmagicdesign SmartView Duo, Developer Information 29 Blackmagic SmartView Ethernet Protocol v1.1 Summary The Blackmagic SmartView Ethernet Protocol is a text-based status and control protocol, very similar in structure to the Videohub protocol, that is accessed by connecting to TCP port 9992 on a SmartView device. Upon connection, the SmartView device sends a complete dump of the state of the device. After the initial dump, state changes are sent asynchronously. The SmartView device sends information in blocks which have an identifying header, followed by a colon. A block can span multiple lines and is terminated by a blank line. To be resilient to future protocol changes, cl

• Getting Started 8 Optimizing the Viewing Angle Before you install SmartView high up in a rack, it is a good idea to check the optimum viewing angle by connecting an SDI video signal and then temporarily inverting the unit. The unit will automatically sense the inversion and flip the video images to the correct orientation. The following procedure describes how

• Blackmagicdesign SmartView Duo, Getting Started 15 Ethernet Network Switch If you want to connect several SmartView units to your studio's existing network, you only need to connect one SmartView to the network switch. The rest can be daisy-chained to each other so you don't have to run multiple cables back to a network switch. Power must be supplied to all units. Network Switch Ethernet Client Computers

• Blackmagicdesign SmartView Duo, Contents SmartView Operation Manual Getting Started Planning your SmartView Installation 4 SmartView Duo product diagram 6 SmartView HD product diagram 7 Optimizing the Viewing Angle 8 Plugging in SDI Monitoring 10 SmartView Duo Connection Diagram 11 SmartView HD Connection Diagram 12 Connecting SmartView to a Network 13 Direct Ethernet Connection 14 Ethernet Network Switch 15 Installing the Blackmagic SmartView Utility Software 16 Updating the Firmware in Your SmartView 17 Configuring Blackmagic SmartView Utility Software 18 Network Settings Pane: Device Name

• Getting Started 14 Direct Ethernet Connection You can connect the Ethernet port of a computer directly to a SmartView without needing a network switch. Additional SmartView units can be daisy-chained to each other so you don't have to run multiple cables back to a network switch. Power must be supplied to all units.

• Blackmagicdesign SmartView Duo, Welcome 2 Welcome to SmartView. We hope you share our dream for the television industry to become a truly creative industry by allowing anyone to have access to the highest quality video. Video monitoring is needed everywhere in a facility. SmartView Duo provides two completely independent and beautiful 8 inch LCD screens in a 3RU rack housing less than an inch thick. SmartView HD provides an amazing 17" LCD screen in a 6RU rack housing less than an inch thick. All SmartView monitors support SD, HD and even 2K video via 3 Gb/s SDI! Video monitoring is designed to work straight out of the box and our free utility provides the user with an easy and intuitive configuration tool. This

• Blackmagicdesign SmartView Duo, Developer Information 28 DATA STREAM 1 G2041 G2042 G2043 G2045 G2046 G2047 EAV(3FFh) EAV(000h) EAV(000h) EAV(XYZh) LN0 LN1 CRC0 CRC1 ANC/AUDIO DATA SAV(3FFh) SAV(000h) SAV(000h) SAV(XYZh) G1 G2 G3 G5 DATA STREAM 2 B2041 B2042 G2044 B2045 B2046 G2048 EAV(3FFh) EAV(000h) EAV(000h) EAV(XYZh) LN0 LN1 CRC0 CRC1 ANC/AUDIO DATA SAV(3FFh) SAV(000h) SAV(000h) SAV(XYZh) B1 B2 G4 B5 DATA STREAM 3 R2041 B2043 B2044 R2045 B2047 B2048 EAV(3FFh) EAV(000h) EAV(000h) EAV(XYZh) LN0 LN1 CRC0 CRC1 040 … 040 SAV(3FFh) SAV(000h) SAV(000h) SAV(XYZh) R

• Blackmagicdesign SmartView Duo, Getting Started 13 Connecting SmartView to a Network It is not necessary to connect SmartView to a computer in order to view SDI video and you can skip this section if you simply want to view video without making any adjustments. However if you wish to remotely adjust the monitor settings, a network connection will be required. SmartView has two 10/100Base-T Ethernet ports. You can connect the IN port to a network switch or directly to an Ethernet port on your computer. The OUT port can be connected to additional SmartView units or to other netwo

• Developer Information 32 Identification and Tally Settings The Identify flag is transient, and will cause a white border to be displayed around the entire picture for a duration of 15 seconds, after which it will be reset. This feature is primarily aimed at identifying which monitor is currently being configured when it is mounted in a rack comprising multiple units. To tu

• Blackmagicdesign SmartView Duo, Getting Started 17 Updating the Firmware in Your SmartView Once the software installation has been completed and SmartView is powered on, it is a good idea to check that the firmware in the SmartView is up to date. Step 1. Launch the Blackmagic SmartView Utility. Step 2. Connect your SmartView unit to the computer via USB 2.0. Step 3. If no firmware update is required, you will simply see the settings used by your SmartView. Settings can be changed now if desired and this is a good opportunity to give each SmartView a unique "Device Name". Please skip the rest of the steps in this section as your SmartView is already up to

• Blackmagicdesign SmartView Duo, Getting Started 20 Monitor Settings Pane: Brightness, Contrast, Saturation You can use Blackmagic SmartView Utility to make changes to the brightness, contrast and saturation of the monitors when connected to SmartView hardware via Ethernet or USB. Monitor Settings Pane: Adjust both monitors together When this setting is enabled, any changes made to the brightness, contrast and saturation will be applied to both SmartView Duo monitors. Yellow borders will surround both monitors in the software interface to indicate that changes to brightness, contrast and saturation will be applied to both monitors. Deselect this setting if you wish to make independent changes to t

• Blackmagicdesign SmartView Duo, Getting Started 16 Installing the Blackmagic SmartView Utility Software It is not necessary to install any software in order to view SDI video and you can skip this section if you simply want to view video without making any adjustments. However if you wish to adjust the network or monitor settings, you will need to install the Blackmagic SmartView Utility software. The Blackmagic SmartView Utility software runs on the latest Snow Leopard and Lion versions of Mac OS X. On the Windows platform, SmartView Utility software runs on both 32 an

• Blackmagicdesign SmartView Duo, Developer Information 25 Developing Custom Software Using Blackmagic Design Hardware The Blackmagic SmartView Ethernet Protocol allows developers to remotely control Blackmagic SmartView hardware with their own custom software. The Blackmagic SmartView Ethernet Protocol is a text-based status and control protocol. Downloading the Free SmartView Ethernet Protocol The Blackmagic SmartView Ethernet Protocol is free. It is included in the SmartView manual and can be downloaded from http://www.blackmagic-design.com/support/ Joining the Blackmagic Design Developer List The Blackmagic Developer mailing list is designed for technical questions regarding technologies used by Blackmagic Design,

• Getting Started 22 Copy/Paste Display Settings If you have already set up one SmartView unit with monitor settings that you would like to apply to other SmartView units, you can copy and paste the settings to those other units. To do so: • select the already configured unit from the SmartView Monitors pane • go to the Device menu, or alternatively click

• Blackmagicdesign SmartView Duo, Getting Started 12 SmartView HD Connection Diagram This illustration shows the multi-view SDI output of an ATEM switcher connecting to the SDI input of the SmartView HD. PROG SDI MULTI-VIEW SDI AES/EBU IN IN 4 SDI IN 6 SDI IN 3 SDI IN 5 SDI REF IN MULTI-VIEW 1 PROG HDMI PROG USB 2.0 PROG SDI 12V POWER SWITCHER CONTROL IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4 HDMI Note: All SDI and HDMI video connections are SD/HD switchable. SmartView HD ATEM Television Studio

• Getting Started 10 Plugging in SDI Monitoring SmartView monitors feature regular BNC connectors to make it easy to connect cables from other SDI equipment including switchers, cameras, capture cards, decks and disk recorders. After powering on the SmartView and connecting an SDI video source to an SDI In connector, the video should immediately be visible on the corresponding monitor a

• Blackmagicdesign SmartView Duo, Help 24 There Are Four Steps To Getting Help. Step 1. Check out the Blackmagic Design web site www.blackmagic-design.com and click on the “Support” page for the latest support information. Step 2. Call your dealer. Your dealer will have the latest technical updates from Blackmagic Design and should be able to give you immediate assistance. We also recommend you check out the support options your dealer offers as they can arrange various support plans based on your workflow requirements. Step 3. The next option is to email us with your questions using the web form at www.blackmagic-de

• Blackmagicdesign SmartView Duo, Developer Information 27 FIELD 1 ACTIVE F 1 0 0 0 0 0 0 0 0 0 0 0 V 1 1 1 1 1 1 0 0 0 0 1 1 LINE # 1650 1 2 … 14 15 16 … 792 793 … 825 Blackmagic 2K Format – Vertical Timing Reference FIELD 2 ACTIVE F 0 1 1 1 1 1 1 1 1 1 1 1 V 1 1 1 1 1 1 0 0 0 0 1 1 LINE # 825 826 827 … 839 840 841 … 1617 1618 … 1650

• Blackmagicdesign SmartView Duo, Getting Started 9 Step 3. Invert the rear assembly. Step 4. Reinstate the face plate on the inverted rear assembly. Step 5. Reinstate the screws in the SmartView chassis. SmartView is now ready to be installed in a high position in a rack. Once bolted into a rack, SmartView will continue to display the optimum viewing angle, even if bumped, as there are no external knobs or adjustments to mishandle or to come loose.

• Blackmagicdesign SmartView Duo, Getting Started 21 Monitor Settings Pane: Identify monitor Enable this setting to display a white border on the selected SmartView monitor. If you have several SmartView units on a network, this setting makes it easy to identify the selected monitor. The white border will appear both on the LCD monitor and in the Blackmagic SmartView Utility software interface. If this setting is used with SmartView Duo in conjunction with the "Adjust both monitors together" setting, the white border will be displayed on both monitors. You can use Blackmagic SmartView Utility to enable or disable the "Identify monitor" setting when connected to SmartView hardwar

• Blackmagicdesign SmartView Duo, Getting Started 19 If no SmartView monitors are found on the network, some units might not have received an IP address via DHCP and it will be necessary to manually configure each unit with appropriate network settings. To do so, connect a SmartView to your computer via a standard USB 2.0 type A-B male cable and launch the Blackmagic SmartView Utility. If the utility prompts you to update the firmware, refer to the previous section named "Updating the firmware in your SmartView". The USB-attached SmartView unit will be automatically selected in the SmartView Monitors pane and will show a USB icon next to its name. You will be able to change all device name,

• Blackmagicdesign SmartView Duo, Getting Started 11 ANALOG I/O DIGITAL I/O (AES/EBU) DIGITAL I/O AUDIO OUTPUT REF INPUT INPUT HD SDI INPUT HD SDI OUTPUT FORMAT CONV. OUT (OPTION) MONITOR1 2 SD SDI OUTPUT FC OUT BOUTPUT AUDIO A 1 2B(OPTION) B(OPTION) B(OPTION) B(OPTION) 1 A 2 A MONITOR A 1 2 MONITOR INPUT MONITOR B INPUT MONITOR CH1/2 CH3/4 CH5/6 CH7/8 CH9/10 CH11/12 AUDIO MONITOR OUTPUT CUE HD REF OUT SD OUT TIME CODE IN OUTR L CH3 CH4 1 2 1 SYNC 2 COMPOSITE (MONITOR) CH1 CH2 IN OUT CH1/2 CH3/4 CH5/6 CH7/8 CH9/10 CH11/12 REMOTE 2 PARAL

More Instructions:

	Blackmagicdesign SmartView Duo Installation and operation manual 19-12-2023 36	DOWNLOAD
	Blackmagicdesign SmartView Duo Operation manual 05-04-2023 25	DOWNLOAD
	Blackmagicdesign SmartView Duo Installation and operation manual 05-02-2023 37	DOWNLOAD

Related Products and Documents (Monitor):

Comparable Devices:

Similar Resources:

• Samsung S24A650S (94 pages) User ManualSyncMasterS22A650SS24A650SThe color and the appearance may differ depending onthe product, and the specifications are subject tochange without prior notice to improve the performance.BN46-00081D-03 …

• ViewSonic VP181 (2 pages) 18.1" Active Matrix LCD Color DisplayThe road to innovative, award-winning technology is led once again by ViewSonic’sintroduction of the VP181 ViewPanel – the first 18" multi-functional flat panelto incorporate digital, analog and composite video inputs into an all-in-one display.With it thin 4.0" panel profile, the ergonomically designed …

• Epson PowerLite 765c (57 pages) EPSON PRODUCT SUPPORT BULLETIN Date: 06/10/2009 Originator:DS TIB #: PSB.2009.06.002 Authorization: Reference: TI 09-08j Rev. A Total Pages:8 Product(s): PowerLite 735c / 737c / 745c /755c/ 765c / 835p /1705/1715/1815/1825/7850p / 8300 with EasyMP.net option, Pro G5150/G5350 / 1725 / 1735W / 85 / 825 / 826W Subject: Release of EMP NS Connection for Windows …

• Sharp LL-T15G3 (25 pages) LCD MonitorLCD FarbmonitorMoniteur LCDMonitor LCDMonitor LCD !"=== = !LL-T15G3OPERATION MANUALBEDIENUNGSANLEITUNGMODE D’EPLOIMANUALE D’USOMANUAL DE FUNCIONAMIENTO !" …

• Acer AL506 (54 pages) ACER Monitor AL506 － Table of C …

• LG MP-42PZ12 (20 pages) PLASMA MONITORSERVICE MANUALCAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.CHASSIS : NP-00LGMODEL : MP-42PZ12website:http://biz.LGservice.come-mail:http://www.LGEservice.com/techsup.html …

Comments, Questions and Opinions: