ElyQ Vision 50 Operation & User’s Manual

Text of ElyQ Vision 50 User Guide:

• ElyQ Vision 50, Spare Parts EQ0382 Flap Dampers 90° (Progressive) EQ0506-UP Clutch Bell EQ0518 96T Main Spur Gear EQ0518-P Drive Gear Pinion 11T with Nut EQ0030 SUS Tail Rotor Shaft EQ0016 Tail Pitch Control Lever EQ0027-UP Carbon Reinforce Tail Case EQ0355F Flap Collar EQ0017 Tail Pitch Slider EQ0239 Canopy Clip set EQ0372 Thrust Collar EQ0148-UP Tail Rotor Grip (Reinforced) EQ0520 686XL Tail Drive Belt SE (T) EQ0018-UP Main Shaft Lock Ring EQ1008 Swash Plate Assy EQ1011 Flybar Seesaw Lever EQ2056-V2 Carbon Tail Boom Brace Set EQ10368 Tail Pitch Control Fork (Metal) EQ10361 Tail Boom V50 with Logo (Ca

• ElyQ Vision 50, Ely Q S010-1 EN DE FRIT (Bag EQ3005) Tail Unit Assy Make up the assy according to the drawing. Please take care of the PIN (13) and screw (34) subassemblies. These components must be tighten firmly and the screw must be impregnated with a small drop of medium seal locktite (blue). The Self Tapping screws (20) and (24) must not be over tighten, because they must ensure a good seal without over fastening. Each screw identified by the “Locktite” symbol, must be impregnated with a small drop of medium seal Locktite (blue). Add a tiny drop of

• Ely Q S018-4 Vision 50 - Competition / Italy 17-07-2009 Flybar Collar ?Non serrare il Flybar Collar tra il Seesaw Lever e il Control Flybar Rod. Importante: questo componente deve essere libero di ruotare intorno alla flybar. ?Do not tighten the Flybar Collar between Seesaw Lever and Control Flybar Rod. Important: this component must freely rotate around the flybar. Ely Q Flybar

• ElyQ Vision 50, Ely Q S011-1 EN DE FRIT (Bag EQ3006) Tail Support Rod Assy Make up the assy according to the drawing. The Self Tapping screws (3) must not be over tighten, because they must ensure a good seal without over fastening. (Bag EQ3006) Tail Support Rod Assy Eseguire il montaggio seguendo lo schema. Le viti autofilettanti (3) non devono essere serrate in maniera eccessiva. Le stesse devono assicurare una buona tenuta ma senza eccedere nel serraggio. Incollare con epossidica (30min.) (Bag EQ3006) Tail Support Rod Assy Führen Sie die Montage nach dem S

• ElyQ Vision 50, Ely Q Main Rotor Head Assy (Part 1.01) Glue width: approx. 1mm Blue Locktite Blue Locktite Blue Locktite Blue Locktite Blue Locktite Blue Locktite Blue Locktite S018-3 Vision 50 - Competition / Italy 13-05-2009 190.5 190.5 27.5027.50 4 7 7 9 9 6 4 5 10 19 19 15 17 17 17 17 17 17 17 10 Blue Locktite Blue Locktite Blue Locktite Blue Locktite 90.50 83.55 BAG EQ3015-21 Preview Socket screw M2x4 (x16) 17 Set Screw M4x4 (x1) 15 Set Screw M3x4 (x2) 10

• ElyQ Vision 50, Ely Q Main Rotor Blades S021-2 Preview Item Code Description Q.ty 1 8203500A Main Grip Socket Screw M4x27 (17+10) 2 2 8203100A Lock nut M4 2 3 8010800A Fuel Tank Rubber Seal 500mm (V50c) 1 1 2 3 2 D B A C Blades not included BAG EQ3018 Vision 50 - Competition / Italy 13-05-2009 Socket Screw M4x27 (17+10) (x2) 1 Lock Nut M4 (x2) 2 Cyano acrylate 3 Cyano acrylate A - L = 55mm B - L = 80mm C - L = 86mm D - L = 20mm A=55mm D=20mm B=80mm C=86mm 01020304050607080

• ElyQ Vision 50, Preview Ely Q Fuel Tank Assy BAG EQ3000 6 5 4 3 2 1 S001-2 Vision 50 - Competition / Italy 13-05-2009 1 8003100A Fuel tank stopper 1 2 8004400A Fuel tank nipple 1 3 8010900A Fuel tank (V50c) 1 4 8011000A Silicon fuel tube L=80mm d2.5, D6 1 5 8103600A Fuel Clunk 1 6 8402000A Fuel Tank Assy

• ElyQ Vision 50, Main Rotor HUB & Servo Rear Drive Ely Q S020-2 Item Code Description Q.ty 1 8110500A Link M2.3 x 30mm 2 2 8002700B Ball Link A 6 3 8200400A Lock nut M3 1 4 8203400A Socket screw M3x20 (13+7) 1 5 8108800A Tail Rotor Bell Cranck Support (V50c) 1 6 8205100A Socket Screw M2x4 2 7 8601100A Bearing d4, D7, W2.5 2 8 8104400A Ball Type E M2x4 - 2.75mm 2 9 8101900A Collar (d3, D4, W10) 1 10 8106000A Tail Rotor Bell Crank 1 11 8009300A C.F. Rear Servo Rod d3,D4,W220mm 1 12 8107700A Threaded Coupler M2.3-d4 2 13 8200900A Socket Screw M3x14 1 14

• ElyQ Vision 50, Ely Q Engine Mount Assy 1 1 2 S009-2 Blue Locktite Glue width: approx. 1mm Blue Locktite Engine not included Item Code Description Q.ty 1 8108500A Motor Mount Side (V50c) 2 2 8200900A Socket screw M3x14 4 BAG EQ3004 Preview Vision 50 - Competition / Italy 13-05-2009 2 Socket screw M3x14 (x8) 2

• ElyQ Vision 50, Ely Q S022-1 EN DE FRIT (Bag EQ3018) Servo Installation (Part 01) Install the servos according to the drawing. For effective tail control, we recommend using a suitable good quality and very fast servo. Arrange all the links and adjust their length according to the drawing. Use Loctite where indicated. Place the Ball Type E (4) at about 13.5 mm from the center of the servo arm screw. Place the Ball Type E (4) at about 19.5 mm from the center of the servo lever. Assemble and adjust the Link Rod (C) length at about 39 mm. Assemble and adju

• ElyQ Vision 50, Ely Q Glue width: approx. 1mm Blue Locktite BAG EQ3004-10 S009-3 Item Code Description Q.ty 1 8203700A Self Tapping Screw 2.5x12 6 2 8200900A Socket Screw M3x14 4 3 8201200A Flat Washer d3, D8, W1.5 4 4 8010200B Engine Fan Conveyor 1 Preview Vision 50 - Competition / Italy 13-05-2009 Socket screw M3x14 (x4) Self Tapping screw M2.5x12 (x6) Washer d3,D8,W1.5 (x4) 3 2 1 3 2 2 3 1 1 4 1 1 Blue Locktite Blue Locktite Main Frame Assembly (Part 2.01)

• ElyQ Vision 50, Main Frame Assembly (Part 1.00) Ely Q S003-2 BAG EQ3009 Item Code Description Q.ty 1 8109300B Landing Skid Brace Mount (V50c) 2 2 8108000A Tail Pulley Housing (V50c) 2 3 8109400A Tail Boom Clamp (V50c) 2 4 8109100A Frame Spacer Medium (V50c) 2 5 8110600A Frame Spacer Smaller (V50c) 2 6 8108100A Bearing Support d10,D22,W6 (V50c) 2 7 8108900A 26 mm spacer (V50c) 8 8 8108400A Motor Mount Center (V50c) 1 9 10 8110300A Bottom Reinforcement Block 1 11 8108200A Bearing d8,D19,W6 Support (V50c) 1 12 8108300A

• ElyQ Vision 50, Ely Q S015-1 EN DE FRIT (Bag EQ3012) Main Frame Assy (Part 02.1) Make up the assy according to the drawing. Add first the Main Drive Gear Assy (previously assembled) and line up the corresponding holes with main shaft bearing holes. Add the main shaft (1) and tighten the socket screw (4) and the lock nut (5). Insert the Collar (2) and tighten the screws (3) keeping in traction the main shaft (1). Each screw identified by the “Locktite” symbol, must be impregnated with a small drop of medium seal Locktite (blue). Don't over tighten the lock nut (5) and the socket screw (4). An excessive pressure could damage the tail transmission gear. Ple

• ElyQ Vision 50, Ely Q S014-1 EN DE FRIT (Bag EQ3011) Main Drive Gear Assembly Make up the assy according to the drawing. The One Way Auto-rotation Assy comes assembled from the factory. However, we suggest making a quality check. Each screw identified by the “Locktite” symbol, must be impregnated with a small drop of medium seal Locktite (blue). Add one-way bearing grease (please see the One Way Auto-Rotation Assy subassembly) during the ordinary maintenance of the helicopter. (Bag EQ3011) Main Drive Gear Assembly Eseguire il montaggio seguendo lo schema. Il gruppo One Way Auto-rotation Assy viene fornito già assemblato. Verificare

• Ely Q S001-1 Fuel Tank Assy BAG EQ3000 EN DE FRIT (Bag EQ3000) Fuel Tank Assembly The fuel tank comes assembled from the factory. The Silicon fuel clunk tube (4), plugged into the Fuel Tank (3), has a top quality feature and it is designed in order to work with very high nitromethane percentage. In spite of this characteristic, we recommend to make periodic controls to avoid po

• ElyQ Vision 50, Ely Q S021-1 EN DE FRIT (Bag EQ3018) Main Rotor Blades Make up the assy according to the drawing. Add the main blades (not included) so that the entering edges are in the clockwise direction. The main rotor spins clockwise. Tighten the screws (1) in a way that the blades oppose a sufficient resistance both to extension and to closure. If this is the first R/C helicopter you assemble, we heartily recommend asking a skilled pilot for setup help. In this stage, insert the engine starter in the Starter Hex Adapter (please see S005-3, item (1)) and spin freely the part in order to guarantee

• ElyQ Vision 50, Aileron Ch1 Elevator Ch2 Throttle Ch3 Rudder Ch4 Pitch Ch6 Ch1 - Aileron Ch2 - Elevator Ch4 - Rudder Ch3 - Throttle Ch5 - Gyro Gain Ch6 - Pitch Hitec - Futaba RX System 6 channel GYRO Throttle Ch1 Rudder Ch2 Ch4 Aileron Ch5 Elevator Pitch Ch6 Ch1 - Throttle Ch2 - Rudder Ch4 - Aileron Ch3 - Gyro Gain Ch5 - Elevator Ch6 - Pitch Futaba T14 - System 6 channel GYRO Throttle Ch1 Aileron Ch2 Ch3 Elevator Rudder Ch4 Pitch AUX1 Ch1 - Throttle Ch2 - Aileron Ch4 - Rudder Ch3 - Elevator AUX 2 - Gyro Gain AUX 1 - Pitch JR - RX System 7 chan

• Glue width: approx. 1mm Blue Locktite 31 30 33 33 30 29 29 28 28 28 28 27 27 26 26 24 24 23 23 21 22 22 20 34 19 18 17 16 15 15 16 14 14 13 12 11 10 9 8 7 6 5 5 4 4 3 2 1 Tail Unit Assy Ely Q Blue Locktite Blue Locktite Blue Locktite Blue Locktite Blue Locktite Cyano acrylate Preview Bag EQ3005 Large Internal Diameter always go toward the tail Rotor HUB Small Internal Di

• ElyQ Vision 50, Main Frame Assembly (Part 2.00) Ely Q BAG EQ3010 Glue width: approx. 1mm Blue Locktite S004-4 Vision 50 - Competition / Italy 13-05-2009 Preview (V50 Competition) 3 4 4 2 5 6 6 6 6 6 1 1 Blue Locktite Socket screw M3x6 (x2) Selftapping screw 3x12 (x6) Selftapping screw 2x8 (x2) 3 6 4 Item Code Description Q.ty 1 8109200A Canopy Mounting (V50c) 2 2 8010500A Antirotation (V50c) 1 3 8205200A Socket Screw M3x6 2 4 8202500A Self Tapping Screw 2x8 2 5 8010100A Radio Tray (V50c) 1 6 8200000A Self Tapping Screw 3x12 6

• ElyQ Vision 50, 4 4 3 3 2 1 1 Preview Ely Q S013-2 Main Frame Assembly (Part 3.00) Ø 2mm Lock Nut M3 (x2) Socket screw M3x14 (x2) Selftapping screw 3x12 (x2) Item Code Description Q.ty 1 8005100A Tail Rotor Blade 2 2 8200900A Socket screw M3x14 2 3 8200400A Lock nut M3 2 4 8200000A Self tapping screw 3x12 2 BAG EQ3008 Vision 50 - Competition / Italy 13-05-2009 3 2 4

• ElyQ Vision 50, Ely Q Equipment required for Assembly ScissorsScrew DriversHobby cutter knife Socket Drivers 5.5 7 8 10 Cutting Pliers Epoxy Grease Ball Link Pliers PliersHex Wrench 1.5 2 2.5 3 Cyano Acrylate Cyano acrylate Blue Lockite Blue Locktite 243 Standard Servo 4x 600/620 Blades 1x set ElyQ - Voltage Regulator 1x Recommended Tools required for assembly - Attrezzi richiesti per l’assemblaggio - Benötigte Werkzeuge für die Montage - Outils nécessaires pour l'assemblage Heli Engine (.50) 1x Specific Tail Servo 1x Muffler (.50) 1x Engine Starter 1x Receiver (6ch or more) 1x Transmitter 6ch or more 1x Helicopter System H

• ElyQ Vision 50, 2 3 1 4 Item Code Description Q.ty 1 8003700A Canopy Clip Internal 1 2 8004300A Rubber Grommets 2 3 8003800A Canopy Clip External 1 4 8200000A Self Tapping screw 3x12 2 5 8005900B Canopy Fiber Glass V50 Ultimate (White) 1 Preview Ely Q S023-2 5 BAG EQ3019 Vision 50 - Competition / Italy 13-05-2009 Canopy

• ElyQ Vision 50, Ely Q Cooling Fan Assy Item Code Description Q.ty 1 8010000A Fan V50c 1 2 8401000A Clutch assy 1 3 8100400B Fan HUB 1 4 8202300A Socket screw M4x8 2 5 8202400A Socket button head screw M3x6 3 4 Blue Locktite 3 2 1 5 Blue Locktite Blue Locktite Blue Locktite Grease for one way bearing Glue width: approx. 1mm Blue Locktite S008-2 Engine not included BAG EQ3004 Fig. 1 Non montare Do not mount Nicht montieren Ne pas monter Vision 50 - Competition / Italy 13-05-2009 Preview Socket button head screw M3x6 (x3) Socket Screw (x2) M4x8 5 4

• HEADQUARTERS Strada di Oselin, 39 - Remanzacco (UD) / ITALY Tel. +39 (0432) 66.70.35 r.a. Fax +39 (0432) 64.93.78 Http://www.elyq.com e-mail: CHINA G/F shop 1. no.30 Ha Heung Road Tok Wawan, Kowloon Shenzhen - China [email protected] www.elyq.com Company Certified With the Standards UNI EN ISO 9001: 2000 (Quality) Azienda Certificata UNI EN ISO 9001:2000 (Qualit

• Ely Q EN DE FRIT (Bag EQ3009) Main Frame Assembly (Part 01) Make up the assy according to the drawing. The fuel tank and the Guide pulley have already been assembled. Each screw identified by the “Locktite” symbol, must be impregnated with a small drop of medium seal Locktite (blue). The screws M2x4 (29) must not be over tighten, because they must ensure a good se

• ElyQ Vision 50, 10 12 12 14 11 10 10 9 8 7 6 6 5 4 3 2 1 1 1 Tail Assy Ely Q Preview Vision 50 - Competition / Italy 13-05-2009S012-2 11 13 13 Lock Nut M3 (x4) 11 14 Socket screw M3x14 (x2) 13 Washer d3,D8,W1.5 (x4) 10 Selftapping screw 3x12 (x4) 12 Socket screw M3x30 (x3) Item Code Description Q.ty 1 8000800A Tail control guide 3 2 8002200A Horizontal fin clamp lower 1 3 8002300A Horizontal fin clamp upper 1 4 8002500A Horizontal Stabilizer CF 1 5 8002600A Vertical Stabilizer CF 1 6 8002700A Ball link A 2 7 8006000A 686XL Tail Drive Belt 1 8 8009200A Tail Boom V50 with Logo (Carbon Fiber) 1 9 8105900A SUS R

More Instructions:

ElyQ Vision 50 Operation & user’s manual 23-12-2023 60

DOWNLOAD

Related Products and Documents (Toy):

Comparable Devices:

Similar Resources:

• Estes X-15 Series (2 pages) ESTES INDUSTRIES1295 H StreetPenrose, CO 81240#1890www.estesrockets.comPRINTED IN CHINAFLYING MODEL ROCKET KIT INSTRUCTIONSKEEP FOR FUTURE REFERENCE1. ATTACH PARACHUTEROCKET PLANEB. Spike Parachute.C. Fold twice.D. Roll.E. Wrap lines loosely. InsertChute, Shock Cord andNose Cone into Body Tube.NOTE: Only EstesWadding (302274)Recommended.A. Insert 2-3squares …

• Ultrafly FW-190 (12 pages) 請注意．組裝前請先閱讀使用說明書．初學無任何組裝經驗者請與經驗較豐富的高階玩家一同組裝．請在孩童拿不到零件的環境下組裝以確保安全．請保留本說明書方便您日後的快速查閱 PRECAUTION．Please read through the entire instruction manual before you start .．First time builders if not fa …

• Skyrocket Pomsies (2 pages) Press and hold the nose for 1 second to switch to Dance Mode (purple eyes). When the whistle blows, shake Pomsies to the beat of the music. The faster you shake, the faster the music plays. When you hear another whistle, freeze! Hold the nose for another second to return to Pet Mode.Freeze Dance ModeTMWhen you first turn on Pomsies, they are in Pet Mode (tea …

• Fisher-Price 77746 (16 pages) G InstructionsProduct Number: 77746F Mode d’emploiRéférence du produit: 77746D AnleitungArtikelnummer: 77746N GebruiksaanwijzingArtikelnummer: 77746G • Please keep this instruction sheet for future reference, as it containsimportant information.• Adult assembly is required.• Requires three size “AA” (LR6) alkaline batteries for operation (not i …

• nanoplanes Baby Shark (14 pages) Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in assembly.INCLUDED IN THIS KIT:• All laser cut Depron parts• Balsa ailerons, balsa horizontal stabilizer, and balsa elevator• Plywood motor mount• 3 Pus …

• Fisher-Price Y3610 (20 pages) 1Download Imaginext™ Apptivity™ Fortress app. Scan QR code below or go to App StoreSM.5Launch app.2Open playset case. Plug case audio pin into device headphone jack.4Turn OFF Multitasking Gestures (located in device Settings).3Turn playset and device power ON. Close case.Y3610, BMM13Scan the QR code below Scan the QR code below to download the appto down …

Comments, Questions and Opinions: