Hasler HJ 3630 Operating Manual
|
2 Security Advice Prior to initial operation, please do carefully read the following instructions for the sake of both your own safety and printer operating safety. Do always observe any warnings and instructions directly attached to the device. Do carefully keep this manual available in order to be able to check back at any time. The Model 3630 digital printer exhibits state-of-the-art
Hasler HJ 3630, Afterwards, use the “Online” key to go back to online mode. Caution: In the topmost menu display, the change back to the online mode is only possible if “Offline” is marked and the “Online” key is pressed then! Online means the printer can receive and print data from the PC. The offline mode is necessary for executing functions of the printer and for setup purposes. Not always all texts of the display are available in all languages; therefore, they are given in English.
“Dry Timeout” is to control an IR or UV lamp. The signal is delayed in order to not switch off the lamp at the end of the job when there are still products under the lamp. “Divert” to control a diverter (set distance / mm and pulse length /ms) Relay 2 output Default, special Puls, Sort Toggle, Dry Timeout, Divert (see above) Second independent relay to be a
Hasler HJ 3630, Appendix PC-852 (= P852) ASCII: E c ( 17 U Decimal: 27 40 49 55 85 Hexadecimal: 1B 28 31 37 55 PC-860 (= P860) ASCII: E c ( 20 U Decimal: 27 40 50 48 85 Hexadecimal: 1B 28 32 30 55
Hasler HJ 3630, Unwrapping and Assembly The below figure illustrates a #10 envelope which was fed at position B and which runs at centre position to the second belt. The value at the ruler amounts to 16.8 cm. Figure 3-9: Read-off the offset with No. 10 envelope Take over the value and enter it into FlexMail. Figure 3-10: Set the offset in FlexMail for a No. 10 envelope Setting the print area: Depending on the device, the print area of the print units is set in different ways. The print area is configured via the software. We recommend the use of the FlexMail software. The corresponding settings within Fl
Hasler HJ 3630, Hexadecimal: 1B 28 30 4E PC-8 Denmark/Norway (= P8DN) ASCII: E c ( 11 U Decimal: 27 40 49 49 85 Hexadecimal: 1B 28 31 31 55 ICEL (= ICEL) ASCII: E c ( 33 O Decimal: 27 40 51 51 79 Hexadecimal: 1B 28 33 33 4F
Hasler HJ 3630, 1 Introduction With the Model 630 you chose an innovative digital printer featuring HP ink jet technology for printing variable data, e.g. mass mailings with addresses, serial numbers or other variable information and graphic elements. The device is designed for the professional use at a high throughput. In order to ensure long-time and, above all, safe use of the Model 630 and its components, you have to read and adhere to the safety instructions in this user manual before starting installation and operation. Please do always observe any warnings and instructions that are directly attached to the device. All persons using the printer must also be familiarised with t
Hasler HJ 3630, Security Advice Do not try to open or refill a cartridge; this can lead to damage of the printer. 2.3 Location of the Printer When setting-up the printer, make sure that it is located on a plain and even surface which is larger than the printer. The base platform for the printer must be sufficiently stable. Tilting or dropping of the device may lead to injuries or device damage. Choose the location of operation or storage in a way that protects the device from heavy fluctuations of temperature and humidity, from direct solar ra
Hasler HJ 3630, Description of the DDP 4.4.1 What do the keys mean? In online mode, only the “Offline“ key has a function. By pressing it, the printer can be switched offline. The Quick key The Quick key, too, can only be used in offline mode when “Offline” is marked. The Quick key is assigned to two functions: 1: Single-key function: Pressing the Quick key calls up the quick menu directly and at any time for fast operation of the device. 2: Combination function: When the Quick key is pushed and held while another key is pressed, the second function of the selec
Hasler HJ 3630, 8 The Main Menu The device is delivered with menu settings predetermined by the factory. If you want to change, for example, the font type or the font quality, you must go to offline mode. 8.1 The “Quick“ Menu By pressing the Quick key, you can directly and at any time call up the Quick menu for quick operation of the device. By pressing the OK key, the action of the selected menu item can be executed. By means of the Arrow-Up and Arrow-Down navigation keys, navigation within the Quick menu is possible. PRINTER RESET The printer is newly initialised and all data are deleted DELETING WAIT LISTS The printers and spoolers are deleted until there are no da
Hasler HJ 3630, Subsequently, place the support approx. 15 cm before the DDP. By doing this, position the positioning fingers in front of the respective slots of the DDP on the right side of the device. Connect the Dreamfeeder (RS 232 input) to the (RENA Dreamfeeder output). Lock the connection by means of screwing the connectors. With the help of this interface, the DDP and the Dreamfeeder are able to communicate with each other in an intelligent way. Now you can fit the positioning hooks into the rear slots at the DDP. Due to the separation of the print media, it is possible that between the DDP and the Dreamfeeder a difference of potential will
Hasler HJ 3630, · Apply the downwards or upwards navigation key until you reach the “Adjustment Steps” display. In this menu, you can balance the distances of the print units U1 to U2 and the distances of the cartridges Cart. 1 to Cart. 2 and Cart. 2 to Cart. 3. · Navigate using the upwards or downwards key until you reach “Corr. Dist. U1- U2” and confirm with the OK key. Value range: +48 to –48, one step = 0.08 mm (= 1/300 “) Positive values shift the print field of a print unit to the left, negative values shif
Hasler HJ 3630, Unwrapping and Assembly b) Connecting the offline Dreamfeeder to the DDP In order to make sure that the Dreamfeeder feeds the print media into the printer from the correct height, the Dreamfeeder is positioned on a supporting rack. To do this, align the Dreamfeeder in such a way that the two positioning fingers of the support are located on the same side as the ejector roller of the Dreamfeeder, as shown in the following illustration. Figure 3-3: Connecting the Dreamfeeder Put the two plugs of the Dreamfeeder through the bored hole on the upper side of the support and place the Dreamfeeder on the support in such a way that the thread bolts fit into
Hasler HJ 3630, Description of the DDP 4.5 The Display D a y c o u n t e r : 1 C o s t s / 1 0 0 0 A d r: 0 . 0 0 0 M e t e r / S e c o n d : 0 . 0 0 0 X J o b p a g e s / h : 0 6 X 6 d p i N o r o n l i n e Figure 4-3: Display indications Meaning of the displays 1 Counting all printed pages in online mode, after switching the device on 2 Averaged ink costs for the respective print job 3 Averaged transport speed in metres per s
Introduction 1.2 How to Use this Manual In the continuous text you will find general information and descriptions. These are required to be able to execute subsequent working and operating steps. The text is indicated by a dot when the technician or operator is expected to carry out a work step. E.g.: • Carry out the next step now. • Now the next step. Please do always read these w
Hasler HJ 3630, Figure 7-3: Exchanging Ink Tray 3 Push the axis of the carrier plate (2) into the locking. Figure 7-4: Ink tray new and used Note: When inserting, do not apply any force at right angles to the service station. Otherwise, the fastening bracket could deform causing the sealing caps to not be able to seal correctly. The fastening bracket should be prevented from bending; therefore, when inserting the sealing cap carrier, support the bracket with your finger from below.
Hasler HJ 3630, General Information 7.2 Resetting the Ink Counter In offline mode, change to the ink level indication using the “Arrow Left“ key. If one of the bars is marked, the ink level of the respective cartridge is indicated in the display in %. Using “Arrow-Up” or “Arrow-Down”, the current value can be entered. If these keys are pressed for a longer time, then the display shows 10-% steps. With the “Online” key, you go return to online mode again.
Hasler HJ 3630, The Main Menu 8.8.2.3 Layout Alignment Adjustment of the print alignment Nor means normal: the printout is readable from the operator view, Rev means reverse: printing is performed with a rotation by 180°. Paper size Size of the print area or size of the paper: EXEC, LETT, LEGA, LEDG, A3, A4, A5, A6, MONA, C10, INTD, C4, C5, C6, B4, B5, B5JI, INSD , CRD1, CRD2, HAGA, or USER. With the USER option, the paper length can be adjusted, maximum value 508 mm (20 inch). Left margin Adjustable left margin: 0 to 304 mm (0 to 11.9 inch). Mainly important for DOS applications. 8.8.2.4 Font parameter Font 13 internal font
Hasler HJ 3630, On this test print, it can be seen that all print nozzles have ejected the ink simultaneously. Now, for example, the distance between the printheads can be measured. Overlapping Print of a test page Figure 8-2: Overlapping With the help of this printout, it can be seen whether the print cartridges print parallel to each other or if there are mechanical imprecisions. The topmost and the lowermost nozzle row of U1C1, U1C2, U1C3, U2C1, U2C2 and U2C3 is printed and ideally it should be one printed line each. Correction print Figure 8-3: Correction print Cartridge print pattern In multiple test prints, for all cartridges a) the contacts with
3.3 Assembly As a standard, the DDP is operated in connection with the Dreamfeeder. Due to transport reasons, the devices are separately wrapped and shipped. Before initial operation, the two devices must be linked with each other mechanically and electrically. Additionally, all transport locks must be removed. Sequence of assembly: Caution: When operatin
Hasler HJ 3630, The Main Menu MEASURING SPEED Speed measurement of the conveyor belt and indication in mm/sec. or feet/min. SHOW LAST ERRORS Displaying the last error notifications 8.2 Menu Overview When the printer is in offline mode, you may directly change to the superordinate menu by pressing HOME. By means of the navigation keys Arrow-Up and Arrow-Down, navigation within the HOME menu is possible. With the OK or the Arrow-Right key, the respective submenu can be selected. Home = 1 st menu level Printer Config Job Config Service Language Settings 8.3 Printer Configuration Main menu Submenu Options Printer Configuration Maintenance Cleaning cycle C
See above, but with cartridge 2 and 3 of unit 1 Corr. cartr. U2 C1-C2 See above, but with cartridge 1 and 2 of unit 2 Corr. cartr. U2 C2-C3 See above, but with cartridge 2 and 3 of unit 2 8.8.1.5 Boot defaults Centaur search Possibility of adjusting whether during the booting process there should be searched for a Centaur ink system. If this menu item is activated and no Centaur sy
Hasler HJ 3630, 9.3.2.2 8-bit character set There are 256 characters in the 8-bit character set. With this, many national characters are available. In the following, the most commonly used 8-bit character set is illustrated. Figure 9-10: 8-bit character set PC8
DOWNLOAD |
HP Designjet Colorpro GA Printer Operation & user’s manual
Designjet Colorpro GA |
Ricoh Aficio SP 3500SF Printer Installation manual
Aficio SP 3500SF |
Kodak 4000 - EasyShare Printer Dock Printer Quick start manual
4000 - EasyShare Printer Dock |
Konica Minolta C650 Printer Operation & user’s manual
C650 |
Detecto P50 Printer Owner's manual
P50 |
Canon POWERSHOT A75 Printer Basic instructions
POWERSHOT A75 |
Canon SD400 - PowerShot Digital ELPH Camera Printer Operation & user’s manual
SD400 - PowerShot Digital ELPH Camera |
Brother DCP-330C Printer Quick setup manual
DCP-330C |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Acnodes | PC6152 | Operation & user’s manual | acnodes/pc6152-D1H.pdf | 18 Dec 2022 | 77 | 123.72 Mb |
2 | Brandt | GEC2632 | Instruction manual | brandt/gec2632-FZJ.pdf | 12 Apr 2024 | 47 | |
3 | Black & Decker | MOD4 | Owner's manual | black-decker/mod4-2S9.pdf | 14 Oct 2022 | 6 | |
4 | BOB | Duallie MA0501A | Owner's manual | bob/duallie-ma0501a-QVF.pdf | 21 Feb 2023 | 5 | 1.41 Mb |
5 | Studiomaster | MIXDOWN | Owner's manual | studiomaster/mixdown-7WU.pdf | 23 Dec 2023 | 51 | |
6 | 3Com | WL-305 | Operation & user’s manual | 3com/wl-305-UO1.pdf | 15 Jul 2022 | 48 | 0.63 Mb |
CognitiveTPG
Programming GuideA798 Thermal Receipt PrinterMade under one or more of the following U.S. patents: 4886381, 5579043, 5613787, 5651624, 5713678, 5752779, 5789916, 5800080, 5879090, 5887999, 5975776, 6027266, 6085973, 6089450, 6129465, 6155483, 6404452, 6486902, 6504331, 5749277, 6722754, 6739773, 6784909.
…
A798(121 pages) |
Riso
This guide describes total operation features and specifications.052-36061-800Applicable Printer models9150/9150R/9110/9110R7150/7150R/7110/7110R3150/3150R/3110/3110R2150
…
Comcolor Series(201 pages) |
Canon
step 1Unpackp. 2step 2Preparestep 3PrintConnecting the Printer to Your Computerp. 3p. 5p. 6p. 8p. 9p. 10p. 15Separately Sold ItemsMaintenance, Storage and TransportTroubleshootingSpecificationsSafety Precautionsp. 13This guide describes the basic and advanced operations of your SELPHY printer in easy to understand terms.Basic operation is simple! Just three …
Selphy CP520(18 pages) |
Canon
Getting StartedCEL-SS6DA2M0 © CANON INC. 2012Getting StartedHandbuch Erste SchritteGuide de mise en routeGuía de inicioGuida introduttivaIntroductiehandleidingGuia de IniciaçãoStartvejledningStarthandbokAloitusopasPříručka ZačínámeKezdeti lépésekPierwsze krokiÚvodná príručkaAlustamineDarba uzsākšanaParengimo darbui instrukcijaΒασικές …
PowerShot G1(146 pages) |
Canon
Important Safety InstructionsThis chapter provides important safety instructions for the prevention of injury to users of this machine and others, and damage to property. Read this chapter before using the machine and follow the instructions to ensure that you use the machine properly. The Canon online manual site (https://oip.manual.canon/) also provides in …
LBP722Cdw(116 pages) |
Epson
EPSON117”EPSON STYLUS PROEPSON STYLUS PRO 40004000Product Reference Guide 1.0®®Advanced Desktop Printer TechnologyAdvanced Desktop Printer TechnologyFor ProfessionalsFor Professionals
…
4000 - Stylus Pro Color Inkjet Printer(38 pages) |
Cooper Lighting Indoor Furnishing L4009Cooper Lighting L4009 Manual (Doc Type: Indoor Furnishing Brochure & specs) L4009, 1 |
AE Motorized Toy Car RC10T5MPDF User Manual (@1J73L3), AE RC10T5M Motorized Toy Car (20th Feb 2024) RC10T5M, 34 |
Toptech Air Cleaner Technology seriesToptech Air Cleaner Installation manual (File: toptech-technology-series-installation-manual-6, 01st Feb 2024) Technology series, 6 |
Traynor Amplifier YBA-1 MOD1Traynor YBA-1 MOD1 Amplifier Manual YBA-1 MOD1, 12 |
BT Cordless Telephone 3710User Manual: BT 3710 (D45Y82, Upd.13th Dec 2023) 3710, 48 |
RCA Tablet DMT580DUTablet Operation & user’s manual (RCA DMT580DU) DMT580DU, 134 |
Bowflex Fitness Equipment Gym Style Ab Crunch StationBowflex Gym Style Ab Crunch Station Guide (Owner's/assembly manual), @5SQ7ZT Gym Style Ab Crunch Station, 20 |
JVC Camcorder GZ-MG230UCamcorder PDF Instructions manual GZ-MG230U, 80 |
Sanyo Amplifier HT30547Amplifier #WS5J3B HT30547, 2 |
Philips Home Lighting 416204816Specifications for Philips 416204816 Home Lighting 416204816, 2 |
CyberData Network Card VoIP Desktop Intercom#1J653D: VoIP Desktop Intercom Network Card Operation manual VoIP Desktop Intercom, 48 |
Rocstor Storage ROCPRO 900#3637B9: ROCPRO 900 Storage Operation & user’s manual ROCPRO 900, 49 |