Manualios.com

AirLive ARM-201E Operation & User’s Manual

AirLive ARM-201E Manual Online:

4.4, 2422 votes
AirLive ARM-201E User Manual
AirLive ARM-201E User Guide
AirLive ARM-201E Online Manual

Text of AirLive ARM-201E User Guide:

  • AirLive ARM-201E, Current Date/Time: This field displays an updated Date and Time when you reenter this menu. [Time Synchronization] Synchronize time with: You can choose “NTP Server automatically”, “PC’s Clock”, or “Manually” to coordinate the time. Time Zone: Choose the Time Zone of your location. This will set the time difference between your time zone and Greenwich Mean Time (GMT). Daylight Saving: Choose “Enabled” or “Disabled” to use daylight savings time. NTP Server Address: Type the IP address or domain name of your timeserver. Check with your ISP/network administrator if you are unsure of this information. 4.6.3 Firmware You can upgr

  • [Virtual Server] The Virtual Server is the server or server(s) behind NAT (on the LAN), for example, Web server or FTP server, that you can make visible to the outside world even though NAT makes your whole inside network appear as a single machine to the outside world. Rule Index: The Virtual server rule index for this VC. You can specify up to 10 rules. All the VCs with single IP

  • AirLive ARM-201E, Chapter 1: Introduction 1.1 Introduction to this ADSL2+ router NOTE: Throughout this manual, some operation illustrations are based on ARM-201E. The corresponding operations are also the same or similar for ARM-204E. This ADSL2+ router is a full-featured ADSL router that provides Ethernet direct connections to individual PCs or local area network with 10/100 Base-T Ethernet. This product use advanced ADSL chipset solution with complete set of industry standard features and high-speed ADSL, ADSL2 and ADSL2+ Internet access solution

  • AirLive ARM-201E, UPnP (Universal Plug and Play): You can choose “Activated” or “Deactivated” option from this session. Auto-Configured (by UPnP Application): UPnP network devices can automatically configure network addressing, announce their presence in the network to other UPnP devices and enable exchange of simple product and service descriptions. Choose “Activated” option to allow UPnP-enabled applications to automatically configure the ADSL Router so that they can communicate through the ADSL Router, for example by using NAT traversal, UPnP applications automatically reserve a NAT forwarding port in order to c

  • Dynamic DNS: Choose the option for Activated or Deactivated DDNS. Service Provider: The default Dynamic DNS service provider is www.dyndns.org . My Host Name: Type the domain name assigned to your ADSL by your Dynamic DNS provider. E-mail Address: Type your e-mail address. Username: Type your user name. Password: Type the password assigned to you. Wildcard support: Select Yes or No to tur

  • AirLive ARM-201E, Step 4: Right-click Local Area Connection (local network your ADSL hooked up with) and select Properties: Step 5: Select Internet Protocol (TCP/IP) then click Properties: 22 AirLive ARM-201E / 204E User’s Manual

  • AirLive ARM-201E, 4.7.2 System Log The System Log displays data generated or acquired by routine system communication with other devices, such as the results of negotiations with the ISP's computers for DNS and gateway IP addresses. The device keeps a running log of events and activities occurring on the Router. You can click Save Log to display a Windows File Download dialog box that enables opening or saving the contents of the log to your PC. To remove all entries from the list, click Clear Log. New entries will begin accumulating. If the device is rebooted, the logs are automatically cleared. 54 AirLive ARM-201E / 204E User’s

  • AirLive ARM-201E, Four-Port ADSL Router Back Panel (ARM-204E) Descriptions of All Connectors PWR Connect with power adapter 1X Connect with Ethernet Cable to Switch Hub or PC 2X Connect with Ethernet Cable to Switch Hub or PC 3X Connect with Ethernet Cable to Switch Hub or PC 4X Connect with Ethernet Cable to Switch Hub or PC DEFAULT Reset button LINE Connect with phone cable 2.4 Connect Related Devices 1) Connect Router to LINE Plug the provided RJ-11 phone cable into LINE port on the back panel of the router

  • IP address: Fill in IP address 192.168.2.x (x is a number between 2 to 254). Subnet mask: Default value is 255.255.255.0. Default gateway: Default value is 192.168.2.1. Preferred DNS server: Fill in preferred DNS server IP address. Alternate DNS server: Fill in alternate DNS server IP address. You can use ping command under DOS prompt to check if you h

  • AirLive ARM-201E, [NAT] NAT: Select this option to Activate/Deactivated the NAT (Network Address Translation) function for this VC. The NAT function can be activated or deactivated per PVC basis. Default Router: Select whether this PVC will be default router for internet data. [Dynamic Route] RIP (Routing Information Protocol): Select this option to specify the RIP version, including RIP1, RIP2-B and RIP2-M. RIP2-B & RIP2-M are both sent in RIP-2 format, the difference is that RIP2-M using Multicast and RIP2-B using Broadcast format. RIP Direction: Select this option

  • AirLive ARM-201E, . The Quick Start Setup Wizard includes four quick steps: 1) Set your new password. 2) Choose your time zone. 3) Set your Internet connection. 4) Re-start your ADSL router. Please follow the quick start step by step to configure the device. Note: If your ISP doesn’t provide DNS, after you complete Quick Start configuration, please go to Interface Setup  Internet to configure your DNS settings. 28 AirLive ARM-201E / 204E User’s Manual

  • Step 3: Select Internet Protocol (TCP/IP) then click Properties: Configure IP Automatically: Step 4: Select Obtain an IP address automatically and Obtain DNS server address automatically then click OK to complete IP configuring process. 15 AirLive ARM-201E / 204E User’s Manual

  • 59 AirLive ARM-201E / 204E User’s Manual 5.6 Problems with the Internet Access I cannot access the Internet. STEPS CORRECTIVE ACTION 1 Make sure the router is turned on and connected to the network. 2 If the ADSL LED is off, refer to Section 5.1.3 3 Verify your WAN settings. 4 Make sure you entered the correct user name and password. 5 For wire

  • AirLive ARM-201E, 4.5 Access Management 4.5.1 ACL Go to Access Management  ACL to enable remote management. You may use telnet or Web to remotely manage the ADSL Router. User just needs to enable Telnet or Web and give it an IP address that wants to access the ADSL Router. The default IP 0.0.0.0 allows any client to use this service to remotely manage the ADSL Router. ACL: There has Activated & Deactivated option. The default setting is Deactivated which means all IP can an access via router by listed IP address

  • AirLive ARM-201E, 31 AirLive ARM-201E / 204E User’s Manual PPPoA/PPPoE: Select this option if your ISP requires you to use a PPPoE connection. This option is typically used for DSL service. Select Dynamic PPPoE to obtain an IP address automatically for your PPPoE connection. Selection Static PPPoE to use static IP address for your PPPoE connection. Please enter the information accordingly. Username: Enter your username for your PPPoE/PPPoA connection. Password: Enter your password for your PPPoE/PPPoA connection Encapsulation: For both PPPoE/PPPoA connections, you need to specify the typ

  • AirLive ARM-201E, Four-Port ADSL Router Front Panel (ARM-204E) Descriptions of LED status PWR When an active power adapter is connected with router, this LED will light up. LAN4 When port 4 connection with PC or Switch / Hub is established, this LED will light up. LAN3 When port 3 connection with PC or Switch / Hub is established, this LED will light up. LAN2 When port 2 connection with PC or Switch / Hub is established, this LED will light up. LAN1 When port 1 connection with PC or Switch / Hub is

  • AirLive ARM-201E, 4.3 Interface Setup Click an Interface Setup link to set ATM VC values, ISP Encapsulation, configure multi- connection settings, and LAN configuration. 4.3.1 Internet [ATM VC] ATM settings are used to connect to your ISP. Your ISP provides VPI, VCI, settings to you. In this Device, you can totally setup 8 PVCs on different encapsulations if you apply 8 different virtual circuits from your ISP. You need to activate the VC to take effect. For PVCs management, you can use ATM QOS to setup each PVC traffic line’s priority. Virtual Circuit: Select the VC number you want to setup.

  • AirLive ARM-201E, [Multicast] IGMP (Internet Group Multicast Protocol): It is a session-layer protocol used to establish membership in a multicast group. The ADSL supports both IGMP version IGMP-v1 & IGMP-v2. Select None to disable it. Note: Every time you change one setting, you must click SAVE button once, and then go to next setting’s change. 4.3.2 LAN There are the IP settings of the LAN Interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is provided to your internal network and cannot be seen on the Internet.

  • AirLive ARM-201E, Destination IP Address: This parameter specifies the IP network address of the final destination. IP Subnet Mask: Enter the subnet mask for this destination. Gateway IP Address: Enter the IP address of the gateway. The gateway is an immediate neighbor of your ADSL Router that will forward the packet to the destination. On the LAN, the gateway must be a router on the same segment as your Router; over Internet (WAN), the gateway must be the IP address of one of the remote nodes. Metric: Metric represents the “cost” of transmission for routing purposes. IP Routing uses hop count as the measurement of cost, with a mini

  • AirLive ARM-201E, 2) Select Gateway tab and add default Router IP Address “192.168.2.1” in the New gateway field and click Add. Under DNS Configuration tab, select Enable DNS and add DNS values (192.168.2.1) in DNS Server Search Order field then click Add. 13 AirLive ARM-201E / 204E User’s Manual

  • AirLive ARM-201E, For Windows XP Step 1: Click Start then select Control Panel (in the Classic View). Step 2: Double-click Network Connections icon. 17 AirLive ARM-201E / 204E User’s Manual

  • AirLive ARM-201E, Chapter 2: Hardware Installation 2.1 Package Contents  ADSL Ethernet Router  RJ-45 Ethernet cable  RJ-11 Phone cable  Power Adapter  CD  Quick Installation Guide 2.2 Front Panel Indicators and Description Front panel of ADSL router has LED indicators to display router’s operating status. One-Port ADSL Router Front Panel (ARM-201E) Descriptions of LED status ADSL When connection with Internet (ADSL Connected) is established, this LED will light up. When this LED is flashing: NO ADSL physical connection DATA When router is transferri

  • AirLive ARM-201E, Chapter 5: Troubleshooting If the router is not function properly, first check this session for simple troubleshooting before contacting your Internet service provider (ISP) for support. 5.1 Using LEDs to Diagnose Problems The LEDs are useful aides for finding possible problem causes. 5.1.1 Power LED The PWR LED on the front panel does not light up. STEPS CORRECTIVE ACTION 1 Make sure that the power adaptor is connected to the router and plugged in to an appropriate power source. Use only the supplied power adaptor. 2 Check that the router and the power source are both turned on and the rout

  • AirLive ARM-201E, Chapter 3: Connecting ADSL2+ Router via Ethernet You can connect ADSL2+ router with PC through either Ethernet cable. After connection is established, you can configure the host PC to be a DHCP client. You have to repeat the same steps for every host PC on your network if you use DHCP function on your router. 3.1 Setup ADSL2+ router via Ethernet Cable If there is an available LAN card present on your PC, you just simply connect ADSL router and PC through the Ethernet cable.

  • AirLive ARM-201E, Configure IP address Automatically: Step 5: Select Obtain an IP address automatically and Obtain DNS server address automatically. Click OK to finish the configuration. Configure IP Address Manually: Step 5: Select Use the following IP address and Use the following DNS server addresses. IP address: Fill in IP address 192.168.2.x (x is a number between 2 to 254). Subnet mask: Default value is 255.255.255.0. Default gateway: Default value is 192.168.2.1. 19 AirLive ARM-201E / 204E User’s Manual

Related Products and Documents (Network Router):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Tripp Lite P940-08I Specification sheet tripp-lite/p940-08i-83C.pdf 05 Apr 2023 2 0.11 Mb
2 Fisher-Price DELUXE PLUS HEALTHY CARE B0325 Instruction sheet fisher-price/deluxe-plus-healthy-care-b0325-X2V.pdf 31 Jan 2023 16 1.43 Mb
3 Jabra GN 8000-MPA Operation & user’s manual jabra/gn-8000-mpa-3G3.pdf 01 Jul 2023 7 2.14 Mb
4 RIDGID AC9944 Operator's manual ridgid/ac9944-5QY.pdf 15 Oct 2023 20 3.93 Mb
5 Lenovo L2060 Manual  lenovo/l2060-5TI.pdf 25 Feb 2024 26
6 Kramer VS-66H Operation & user’s manual kramer/vs-66h-RKX.pdf 06 Dec 2023 24

Similar Resources:

  • Airlinkplus

    ASW108

    (1 pages)
    Package Contents l One 8-Port 10/100M Ethernet Switch l One AC Power Adapter l One Quick Installation Guide Congratulations on your purchase of the 8-Port 10/100M Mini Switch. This switch integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible mini package. P/N:1907MSW108+7050 Ports 1-8 At the rear site of the …
  • pro bel

    64x64 HD Series

    (12 pages)
    6521 64 X 64 HD SERIES MACHINE CONTROL ROUTERCONTENTS1 INTRODUCTION 32 SPECIFICATION 42.1Inputs42.2Outputs42.3Control42.4Power Requirement42.5Mechanical42.6Operating Temperature42.7Connectors43 GENERAL DESCRIPTION 54 ROUTER DESCRIPTION 65 INSTALLATION 75.1Mechanical75.2Earthing75.3Modules75.4Removal and Replacement Of Sub-Units85.5Installation Note86 CONNECT …
  • Encore Networks

    EN-2000

    (4 pages)
    For information on trademarks, safety, limitations of liability, and similar topics, see http://www.encorenetworks.com/disclaimer.htm. Configuring Traffic Priority for the EN-2000he EN-2000 provides wireless and cabled connections to a local area network (LAN), to a wide area network (WAN), and to peripheral devices and remote devices. This document discusse …
  • Huawei

    S1700 Series

    (8 pages)
    1U 1U=44.45mm Fix the captive nuts. 安装浮动螺母。Use installation strip to fix the captive nuts. 使用安装条安装浮动螺母。 ● Leave more than 1U space between the devices for proper heat dissipation. ● 设备与设备之间的距离必须大于1U。技术支持Service and SupportTool List工具参考斜口钳Diagonal pliersCro …
  • Dynex

    DX-NRUTER

    (2 pages)
    3Setting Up Wireless Security (continued) Conguration de la sécurité sans l (suite)Conguración de la seguridad inalámbrica (continuación)4 When prompted, select your security type, then click Apply Changes. We recommend WPA/WPA2-Personal(PSK) as the security mode and then WPA-PSK+WPA2-PSK as the authentication, because it is the most secure an …
  • ZyXEL Communications

    P-2302R-P1C

    (2 pages)
    Plug and Talk VoIP ATA BenefitsUnified Design Configurable to Bridge/Routing ModeThe bridge/routing can be configured by the users in the WebGUI manually. User can manually let the device fit with various kinds of ITSP network environment. It dramatically reduce ITSP stock management effort by firmware configurable alternatives. Rich Call FeaturesA number of …

Comments, Questions and Opinions: