Manualios.com

Airlinkplus RT210W Operation & User’s Manual

Airlinkplus RT210W Manual Online:

3.05, 1815 votes
Airlinkplus RT210W User Manual
Airlinkplus RT210W User Guide
Airlinkplus RT210W Online Manual

Text of Airlinkplus RT210W User Guide:

  • Airlinkplus RT210W, Wireless Broadband Router User Manual 52 Electromagnetic Compliance • FCC Part 15 Class B • CE • EMI/Immunity: VCCI class B • PTT: JATE 6.2 Software WAN Port Features • PPPoE (PPP over Ethernet) Client with Keep Alive/Connect On Demand Support • PAP and CHAP Authentication • DHCP Client • MAC Address Cloning • Settable and Changeable IP Address LAN Port Features • DHCP Server • Settable and Changeable IP Address Router Features • NAT • Firewall Support • Bridge Mode Support • 802.1D Spanning Tree Bridging • IP Fil

  • Airlinkplus RT210W, Wireless Broadband Router User Manual 36 wireless clients to share the network. In other words, it improves wireless network efficiency and boosts throughput. Figure 4-14 Wireless LAN (2.4 GHz) 4.7 Wireless LAN Security This page configures the wireless security mode. u Network Authentication Network Authentication: Disabled by default. If the local network has an authentication server such as Radius server, the user can

  • Airlinkplus RT210W, Wireless Broadband Router User Manual 16 Check/Renew IP Address under Windows 2000/XP The following steps help you to verify whether the network adapter gets an IP address within the DHCP IP pool range (192.168.1.100 ~ 192.168.1.150 by default) of the router. If not, you may need to renew the IP information. Step 1 Click Run from the Start menu to open the Run dialog box. Step 2 Type cmd in the dialog box and then click OK. Step 3 At DOS command prompt, type ipconfig to see the IP information from DHCP serv

  • Airlinkplus RT210W, i Safety Instructions For Installation • Use only the type of power source indicated on the marking labels. • Use only the power adapter supplied with the product. • Do not overload wall outlet or extension cords as this may increase the risk of electric shock. If the power cord is frayed, replace it with a new one. • Proper ventilation is necessary to prevent the product from overheating. Do not block or cover the slots and openings of the device, which are intended for ventilation and proper operation. • Do not place the product near any source of heat or

  • Airlinkplus RT210W, Wireless Broadband Router User Manual 35 exceeding the fragmentation threshold are fragmented, i.e., split into, smaller units suitable for the circuit size. On the other hand, packets smaller than the specified fragmentation threshold value are not fragmented. RTS Threshold: Request to send threshold. It specifies the packet size beyond which the AP invokes its RTS/CTS mechanism. Packets that exceed the specified RTS threshold trigger the RTS/CTS mechanism. DTIM: Specifies the Deferred Traffic Indicator Map (DTIM) period. This value determines at which interval the AP will send its broa

  • Wireless Broadband Router User Manual 53 Security Features • PAP and CHAP Authentication • ASCII/HEX Format 64/128 Bit WEP Key for Wireless LAN • Allow/Deny List for Wireless LAN • Supports IP packets filtering based on IP address, port number, and protocol Wireless LAN Features • Fully compatible with 802.11g standard • Direct Sequence Spread Spectrum (DSSS) technology expl

  • Airlinkplus RT210W, Wireless Broadband Router User Manual 47 After upgrading, the new firmware version number is displayed in Current Firmware version field. u Restore Factory Defaults All settings set by the administrator will be erased. This option restores all the settings back to factory defaults. To perform this operation, click the Restore button and then wait for a few seconds. You will return to the Administration page when the process is complete. This feature is basically the same as resetting via the reset button (see “ Rear Panel and Connector” ) on the device but it allows you to remotely perform the reset task. u System Reboot: Reboot

  • Airlinkplus RT210W, Wireless Broadband Router User Manual 31 4.6 Wireless LAN (2.4G) Configuration The Wireless Broadband Router implements Access Point capability, which connects wireless clients to a wired LAN. It allows wireless stations to access network resources and share the broadband Internet connection. u Wireless Interface: Displays the MAC address of the wireless interface. u Basic Configuration SSID: Service Set ID. It uniquely identifies a logical network domain name of your WLAN. The default value is wireless. Network Type: An Open AP will periodically broadcast its SSID to

  • Airlinkplus RT210W, Wireless Broadband Router User Manual 14 Check/Renew IP Address under Windows 98/ME The following steps help you verify if your network adapter gets an IP address within the DHCP IP pool range (192.168.1.100 ~ 192.168.1.150 by default) of the router. If not, you may need to renew the IP information. Step 1 From the Start menu, click Run to open the Run dialog box. Step 2 Enter winipcfg in the dialog box and then click OK. Step 3 Select the Ethernet or WLAN adapter from the drop-down list to show the IP add

  • Airlinkplus RT210W, Wireless Broadband Router User Manual 42 Enabled Check this option to enable this setting and remember to click Apply to save and activate the changes. Note LAN MAC Filter demands higher priority than LAN Client Filter. Figure 4-16 Filters 4.9 Forwarding (Router Mode Only) This page allows you to configure the Forwarding feature. Unlike Filter, which governs outgoing traffic, Forwarding is used to control external access to the local network. This is commonly used when you have publicly accessible virtual servers on your local network. By default, forwarding entry is empty and any external access to your LAN is blocked. Once you define a forward

  • Wireless Broadband Router User Manual 6 LEDs Color Status Description Solid Ethernet connection is established. • Amber - 100 Mbps Ethernet connection • Green - 10 Mbps Ethernet connection. Blinking Transmitting/receiving packets on the LAN port. Off Power is off or no broadband device is connected. On Broadband device is connected. WAN Green Blinking Transmitting/receiving

  • Airlinkplus RT210W, Wireless Broadband Router User Manual 15 Then an IP address will be automatically assigned to your computer. Option B: Using Fixed IP Address Select Use the following IP address and enter these settings: • IP address: 192.168.1.x (x is between 2 and 254) • Subnet mask: 255.255.255.0 • Default Gateway: 192.168.1.1 Step 5 Click OK twice to finish the configuration.

  • Wireless Broadband Router User Manual 25 Username/Password: Enter the username and password provided by the ISP used to log on to the Internet. Connection Mode: Select your PPP connection from these options: Keep Alive: This feature will keep your Internet connection always alive. The Wireless Broadband Router sends echo requests periodically to the ISP to prevent the connection from being termin

  • Airlinkplus RT210W, Wireless Broadband Router User Manual 29 DHCP Lease Time: Specify the time that a network device can use a private IP address before the DHCP server reassigns the IP address. IP Pool Range: Specify the starting and ending IP address of the IP address pool. Whenever a network device requests an Internet session, the router will allocate an unused IP address from this pool and lease them to the device for a specified amount of time. u LAN Spanning Tree Protocol (Router Mode Only) Select whether to enable or disable this function. Spanning Tree Protocol stops network loo

  • Airlinkplus RT210W, iv About This User Manual For brevity, throughout this manual the “ Wireless Broadband Router” is referred to as “ the router” or “the device” and following terms or abbreviations are used interchangeably: • Access Point – AP • Wireless LAN – WLAN • Ethernet network – LAN – network Note and Caution in this manual are highlighted with graphics as below to indicate important information. Note Contains related information that corresponds to a topic. Caution Represents essential steps, actions, or messages that should not be ignored. This User Manual contains information on how to install and configure your Wireless Broadband Ro

  • Airlinkplus RT210W, Wireless Broadband Router User Manual 18 3. The Wireless Broadband Router shall reply and a similar screen as below is shown. This indicates the Wireless Broadband Router and the wired/wireless host can communicate. If you get a failed ping response such as: Request time out Request time out Request time out Request time out or Destination host unreachable Destination host unreachable Destination host unreachable Destination host unreachable Then the connection has failed. Verify whether the network setting is correct. For Ethernet client, also check the cable between the router and the PC. Restart the computer if necessary.

  • Airlinkplus RT210W, Contents vii List of Figures Figure 2-1 LED Indicator .......................................................................... 5 Figure 2-2 Rear Panel and Connector..................................................... 6 Figure 2-3 Typical Connection Diagram.................................................. 9 Figure 4-1 Applying Changes................................................................. 20 Figure 4-2 System Overview – Router Mode ........................................ 21 Figure 4-3 System Overview – Bridge Mode......................................... 22 Figure 4-

  • Airlinkplus RT210W, Wireless Broadband Router User Manual 45 Figure 4-17 Forwarding 5.0 Administration This page allows the administrator to perform the following settings: u System Clock Network administrators may synchronize date and time among network devices by synchronizing the local clock to an available NTP (Network Time Protocol) server. NTP Server: Enter IP address of the NTP server. Up to three entries are allowed. Time Zone: From the drop-down menu, select a time zone according to your geographic location.

  • Airlinkplus RT210W, Wireless Broadband Router User Manual vi 4.5 LAN Configuration.....................................................28 Viewing Current DHCP Assignments (Router Mode Only).................................................................30 4.6 Wireless LAN (2.4G) Configuration ............................31 4.7 Wireless LAN Security...............................................36 4.8 Filters (Router Mode Only).........................................40 4.9 Forwarding (Router Mode Only).................................42 5.0 Administration ....................................................

  • Airlinkplus RT210W, Wireless Broadband Router User Manual 44 the Wireless Broadband Router how to direct traffic across networks. Item Description Outbound Protocol Specifies the protocol the application uses. TCP or UDP Outbound Port Start/End Enter the WAN port range from which data that follows that particular protocol should be sent. Inbound Protocol Select the protocol (UDP or TCP) for the port. Inbound Port Start/End Enter the WAN port range from which data that follows that particular protocol will return. To Port Start/End Enter the LAN port range. Enabled Select this option and click Apply to activate the configuration. u Static Routes In this sect

  • Wireless Broadband Router User Manual 50 provided by the ISP. • For cable users, if your ISP requires a registered Ethernet card MAC address, make sure you have cloned the network adapter’ s MAC address to the WAN port of the router. (See the MAC Address field in WAN page.) My wireless client cannot communicate with another Ethernet computer. • Ensure the wireless adapte

  • Airlinkplus RT210W, Wireless Broadband Router User Manual 3 1.3 Package Contents Check the contents of the package. If any item is missing, please contact the dealer from whom the equipment was purchased. • Wireless Broadband Router x1 • Power Adapter and Cord x1 • CD x1 • RJ-45 Ethernet Cable x1 • Quick Installation Guide x1 1.4 System Requirements • Cable/ADSL modem and an Internet access account for Internet connection • One computer with 10/100Base-T Ethernet card and TCP/IP protocol installed for initial setup • Internet Explorer 5.0 or higher for Web configuration • 802.11g or 802.11b compliant wireless adapters (for wireless connection)

More Instructions:

DOWNLOAD

Related Products and Documents (Network Router):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Philips PR1902C Brochure philips/pr1902c-339.pdf 13 Aug 2023 2
2 Life Fitness T5 Руководство пользователя life-fitness/t5-696.pdf 23 Oct 2023 33
3 Whirlpool AWZ 475 Programme chart whirlpool/awz-475-E5Z.pdf 09 Dec 2023 2
4 VTech SN6307 Operation & user’s manual vtech/sn6307-3TN.pdf 31 Jul 2023 2
5 Worksman MG Owner's manual worksman/mg-T25.pdf 29 Jul 2022 3
6 Epson ActionNote 866C Product information manual epson/actionnote-866c-V88.pdf 25 Nov 2023 10 0.28 Mb

Similar Resources:

  • Robustel

    R3000-Q3PA

    (112 pages)
    Robustel GoRugged R3000 Quad Dual SIM Industrial Cellular VPN Router For GPRS/EDGE/UMTS/HSPA+/LTE Networks User Guide Document Name: User Guide Firmware: 2.0.0 Date: 2016-11-15 Status: Confidential Doc ID: RT_UG_R3000 Quad_v.2.0.1 www.robustel.com …
  • Horizon Fitness

    Vision I232-S

    (11 pages)
    Horizon Vision I232-S LTE CPE Quick Start Model:I232FCC ID:2ADX3I232Model:I232FCC ID:2ADX3I232 …
  • CalAmp

    Vanguard 3000 VG3000-PXS-F

    (122 pages)
    VANGUARD 3000™ MULTICARRIER 3G CELLULAR BROADBAND ROUTER User Manual Vanguard 3000™ Fixed and Mobile Routers PN 134732-VG3000 Rev. D Revised July 2016 …
  • RFM

    DN-2400E

    (21 pages)
    www.RFM.com Technical support +1.678.684.2000 Page 1 of 21 © 2011 by RF Monolithics, Inc. E-mail: [email protected] DN-2400E User Guide - 08/05/11 DN-2400E DN-2400EP 2.4 GHz Wireless Ethernet Bridges User Guide …
  • ZyXEL Communications

    P-663HN-51

    (84 pages)
    P-663HN-51 Support Notes 1 All contents copyright © 2009 ZyXEL Communications Corporation. P-663HN-51 802.11n ADSL2+ Bonde …
  • D-Link

    DWR-910

    (1 pages)
    The web UI allows you to configure the DWR-910’s advanced settings. To access the web UI: 1. Connect the DWR-910 4G LTE USB Router to your computer. 2. Enter 192.168.0.1 into your web browser to access the web UI. The web UI login screen will then appear.3. Enter admin as the account name and leave the password area blank. Then press Login to access and …

Comments, Questions and Opinions: