Maytag Services MAH9700A Technical Information

Text of Maytag Services MAH9700A User Guide:

• Maytag Services MAH9700A, 27” Front Load Washer - Technical Information June 2006 1 16026736 ©2006 Maytag Services MAH9700A* • Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit. • Refer to Service Manual 16025909 for detailed installation, operating, testing, troubleshooting, and disassembly instructions. CAUTION ! All safety information must be followed as provided in Service Manual 16025909. ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before se

• Maytag Services MAH9700A, Component Testing Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. 16026736 2 June 2006 ©2006 Maytag Services NOTE: See “Machine Control Board” on next page for pin and connector locations. Illustration Component Test Procedure Results Thermistor Unplug harness connector and test from wire insertion side of connector. Pin #6 and Pin #3 of CN3.................... 13K ohms @ 70F/21C (2.5V DC) Door Switch Check voltage at Pin #6 and Pin #4 of CN3............................

• Maytag Services MAH9700A, Component Testing Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. June 2006 3 16026736 ©2006 Maytag Services 1 2 3 CN10 CN9 CN3 CN11 CN6 CN7 CN5 R Y 9 CN8 9 1 1 5 1 4 4 1 8 5 3 1 3 1 Motor Normal resistance is approximately 11.6.0 Ω between any 2 pins (1,2 or 3) on motor t Machine Control Board MEMS Sensor 1 2 2 1

• Maytag Services MAH9700A, Troubleshooting Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. 16026736 4 June 2006 ©2006 Maytag Services Will Not Start • Plug cord into live electrical outlet. Check for proper voltage. • Check fuse or reset circuit breaker. • Push any key to turn ‘ON’ the clothes washer and press the Rotary Cycle Selector knob to start the clothes washer. • Close door and push the Rotary Cycle Selector knob to start the clothes washer. • Check to see if the

• Troubleshooting Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. June 2006 5 16026736 ©2006 Maytag Services Tub Full of Suds • Check for restricted drain system. See Will Not Drain and Will Not Spin. • Check for loose wire connec

• Maytag Services MAH9700A, Troubleshooting Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. 16026736 6 June 2006 ©2006 Maytag Services Vibration/Walking/Noise • Check for proper load size and distribution. • Check for proper installation. • Verify unit has new motion sensor / control board. • Check vent flappers for foam present on flapper. • Check for loose pump to bracket screws. • Check for stripped pump mounting bolts. • Check location of top suspension springs. • Check console for broken plastic locating tabs, check f

• Maytag Services MAH9700A, Troubleshooting Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. June 2006 7 16026736 ©2006 Maytag Services # IN Service Mode Service Mode enables service personnel to verify the operation of the washing machine and diagnose problems. Service Mode can be entered in the middle of any wash cycle without interrupting the cycle. While in Service Mode, the technician can cancel the curre

• Troubleshooting Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. 16026736 8 June 2006 ©2006 Maytag Services # Quick Spin Test While in Service Mode, press Delay and Rinse & Spin keys to start a Quick Spin Test. Quick Spin Test steps follow: • Sta

• Maytag Services MAH9700A, Troubleshooting Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. June 2006 9 16026736 ©2006 Maytag Services IN Board Input Test While in Service Mode, pressing the Spin Only key will begin the Board Input Test. This test turns on a specified output after a key press. Pressing the Spin Only key again cancels the test. (Display shows “in”). While in Service Mode follow chart to check respective function. • When the Rotary Cycle Selector knob is set to “Super Wash ” and the Rotary Cycle Selector

• Maytag Services MAH9700A, Troubleshooting Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. 16026736 10 June 2006 ©2006 Maytag Services Board Output Test While in Service Mode, pressing the Spin Speed key will begin the Board Output Test. This test turns ‘ON’ a specified output after a key press. Pressing the Spin Speed key again cancels the test. Only one output can be ‘ON’ at any time. All outputs will be turned ‘OFF’ after five (5) minutes of inactivity. • When the Rotary Cycle Selector knob is set to “Super Wash” and the Rotar

• Troubleshooting Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. June 2006 11 16026736 ©2006 Maytag Services Display Diagnostic Codes The diagnostic code display can be toggled ‘ON’ and ‘OFF’ from Service Mode by pressing the Rinse & Spin key and rotatin

• Maytag Services MAH9700A, Troubleshooting Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. 16026736 12 June 2006 ©2006 Maytag Services Diag. Code Description Trigger Action to be taken 15 Stuck Key A key is sensed to be pressed more than 30 seconds, the key will be assumed to be stuck. Display "E2". See LED/Switch Test. Check connection of keypad to control board. Replace console if necessary. 17 Door/Lid switch w

• Maytag Services MAH9700A, Wiring Schematics ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. June 2006 13 16026736 ©2006 Maytag Services Soaking Washing Intermittent 1 Intermittent 2 Final Sanitary EH/C(N) 142/151 2 3 69 (1) (1) (6) (6) (7) 2 4 110 C/C(N) _ 2 3 24 1 (1) (6) (6) (7) 2 4 C/C 61/70 2 3 24 1 (1) (6) (6) (7) 2 4 W/C 95/106 2 3 24 1 (1) (6) (6) (7) 2 4 W/W 95/106 2 3 24 1 (1) (6) (6) (7) 2 4 H/C(N) 120/129 2 3 24 (1) (1) (6) (6) (7) 2 4 C/C(N) _ 2 (3) (13) 1 (1) (6) (6) (7) 2 4 C/C 61/70

• Maytag Services MAH9700A, Wiring Schematics ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power. 16026736 14 June 2006 ©2006 Maytag Services NOTE: Series 10 – 16 do not have connector CN11 or MEMS PCB originally. Series 17

Related Products and Documents (Washer):

Comparable Devices:

Similar Resources:

• Whirlpool LA34ooxs (12 pages) AUTOMATIC WASHER Large Capacity Model LA34ooxs lcrowave Ovens. Trash Compactors. Room Air Condltloners. Dehumtdilwrs. Automatic Washers. Clothes Dryers, Freezers. Refngerator-Fl …

• Whirlpool LSA 1100 (27 pages) SERVICE MANUAL Page | 1 SERVICE MANUAL Vertical Axis Washing Machine Model: LSA 1100 Caution :In this Manual, some parts/technical specification can be changed for improving, their performance without notice in the parts lis …

• Haier HMS1000TVE (30 pages) MODEL： HMS1000TVE FRONT LOADING WASHING MACHINE Service Manual Features： ● 300mm diameter porthole, door may be open at a 180 degrees. ●Multi-gear speed controller ●Unique gasket design featuring no residual water hidden inside ●Delay time adjustive Haier Group MANUAL CODE： No.1 ●Washing Pro …

• Smeg WD1160 (9 pages) 0160, 1160, 4060, 4190 Power Connection Conversion instruction Page 1 - 9 WD1160, WD4060, WD4190 GW0160, GW1160, GW4060, GW4190 - POWER CONNECTION CONVERSION INSTRUCTIONS - - Technical Procedure - 0160, 1160, 4060 4190 19 561 0144 00 - EN 26/05/2017 Rev. Date WARNING This document is intended for authorised Smeg technical staff and must be …

• Morris WDW-91480 (29 pages) A NOTE TO YOUThank you for buying a MORRIS appliance.MORRIS washers are easy to use, save time, and help you manage your home better.This manual contains valuable information about how to operate and maintain your washer properly and safely.Please read it carefully.INSTRUCTION MANUALWDW-91480Washing Machine Instruction Manual␊ Economic wash systemUsing art …

• AEG Electrolux EWT641 (8 pages) 11. TECHNICAL CARACTERISTICS2. WARNINGSKeep this user’s manual with your washing machine. If you sell your washing machine or give it away, make sure that it isaccompanied by its user’s manual. The new user can then be informed of how the washing machine operates and readrelevant warnings. These warnings have been written for your safety and for the safe …

Comments, Questions and Opinions: