GE ZIS48N Custom Options Manual And Installation Instructions
|
17 Installation 48" Built-In Refrigerator Step 3 Install Side Panels Step 4 Roll Refrigerator Into Opening Step 5 Level Refrigerator • Side panels are not required when the refrigerator is installed into an enclosure. Skip this step if you are installing in an enclosure. • Side panels are required whenever the sides of the refrigerator will be exposed and wh
GE ZIS48N, 15 Installation 48" Built-In Refrigerator Tools Required • Tinsnips to cut banding • Stepladder • Bucket • Level • Appliance Hand Truck • Tubing cutter • 7/16" open-end wrench • #2 Phillips screwdriver • Stubby Phillips screwdriver • Drill and appropriate bits • 7/16" socket with 3" extension for ratchet • Safety glasses Hardware Supplied Materials Required Flooring • Water shut-off valve (optional but recommended) • Water filter WR97X0214 (optional but recommended) • Custom panels for fresh food, freezer compartments, grille panel • 1-1/2" stamped open-end wre
GE ZIS48N, 43 ZKHTSS1 for 3/4" Panels Tubulor Stainless Steel Handles Step 2: Match Handle Extrusions to Panels • Cut a piece of corrugated to use as a pad to protect the panel finish. Use 1/2" thick section of plywood to protect flooring when drilling. • Place custom panels on the pad, appearance side down. Note: If panels are wood, be sure to note which end is the top so that wood grain is in the correct direction on both (or all 3) panels. • Place new extrusion against the handle side of the panels. • Align the extrusion evenly with the top and bottom of the panel. • Follow the same procedure on the opposite panel. • Tape the extrusions to the
GE ZIS48N, 9 Custom Panel Dimensions 48" Built-In Refrigerator ZIS48N (non-dispenser) • ZKT48 and ZKHT1 installed together provides for the installation of 3/4" custom door and grille panels, using a custom handle, of your choice. Order ZKHTSS1 for tubular stainless-steel handles. Cut panels to size, rout the handle side of the panels as shown below and install. Custom Door Panel Dimensions Using Trim Kits ZKT48 3/4" thick panel with custom handle Installation Height Dimension A 83" 8-1/4" 83-1/2" 8-3/4" 84" 9-1/4" 84-1/2" 9-3/4" Important: Maintain 1-1/2" min. g
Note: Optimal final appearance depends on careful routing depth. Do not exceed 1⁄4" routing depth. • Position the handle bracket onto the steel door by matching existing screw holes on the door and bracket. • Re-install dispenser trim, temporarily. • Determine the desired location of the custom handle and carefully mark centerlines of the screw holes. • Drill
GE ZIS48N, Step 3 Assemble panel, extrusion and handle Extrusion 3/4" Min. 1-1/2" Max. Handle Decorator Door Panel ZKH1 Trim Kit (For 1/4" Panels) Support for Custom Handles Option 1 Installation • Remove the door extrusions and door panels. • Drill 1/16" pilot hole through extrusion. • Drill clearance holes through the panel and extrusion. • Assemble the door panel, extrusion and custom handle. • Install screw(s) long enough to pass through the extrusion, door panel and into the handle. • Slide the assemb
GE ZIS48N, Note: While performing installations described in this book, safety glasses or goggles should be worn. To obtain specific information concerning any Monogram product or service, call GE Answer Center ® consumer information service at 800.626.2000–any time, day or night. For Monogram TM local service in your area, call 1-800-444-1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Pub. No. 49-6962 Part No. 162D9630P001 © 1997 GE Appliances Printed in U.S.A. ( NAI 283) 10/98 5A8827-02 Monogram. ® General Electric Company Louisville, KY 40225
GE ZIS48N, 35 ZKHT1 Trim Kit (For 3/4" Panels) Support for Custom Handles Option 1 Installation Step 3 Assemble panel, extrusion and handle Step 4 Mount assembled panels • Remove the door extrusions and door panels. • Drill 1/16" pilot hole through extrusion. • Drill clearance holes through the panel and extrusion. • Assemble the door panel, extrusions and custom handle. • Install screw(s) long enough to pass through the extrusion, door panel and into the handle. • Place assembled panel on
GE ZIS48N, 11 Custom Panel Dimensions 48" Built-In Refrigerator ZISW48D (white dispenser) ZISB48D (black dispenser) Standard Trim with 1/4" Panels • 1/4" Panels: Cut panels to size. • Custom handles with 1/4" door panels require Trim Kit ZKH1. When using ZKH1 with the standard dispenser trim, the length of the custom handle, top to bottom cannot exceed 11-3/4". • Tubular stainless steel handle kit, ZKHSS1. • Custom collar dispenser trim with 1/4" door panels require trim kit ZWCD2. Standard Trim with Panels secured to 1/4
GE ZIS48N, 19 Installation 48" Built-In Refrigerator Step 7 OPTION 1 Secure refrigerator at the top To prevent the refrigerator from tipping over, you must: • Install a wood block, the full width of the refrigerator. Secure the block with wood screws penetrating at least 3/4" into wall studs. Block Soffit Side View Side View When using 1/2" to 3/4" side panels, the front flange of the case trim is attached to the side panel. • Open freezer door to access case trim. • Drill hole in case trim slightly below top hinge. Drive screw through the trim and into the side panel. • Follow the same procedure on the fresh food side. OR If refrigerator is i
GE ZIS48N, 38 This kit provides for the installation of Stainless Steel custom handles on 1/4" thick decorator door panels. The door extru- sions allow these custom handles to be secured to the door structure, rather than to the custom panels. This kit contains all the necessary parts for dispenser and non-dispenser models. Step 1: Remove Handles • Carefully remove the phillips head screws from the door handle top endcaps, if present. • Open doors to 90°. Remove the screws from the full- length handles of both doors. • Retain screws, discard handles and endcaps. • Locate the 2" x 2" adhesive foam pads packed with the refrigerator. Apply pads to
GE ZIS48N, 27 ZKT48 Trim Kit 3/4" Custom Panels G A B E F J I H C D Tools and materials required: •#2 Phillips screwdriver •Stubby Phillips screwdriver •Drill and appropriate bits •Safety glasses •Custom panels Parts List: Freezer Door A. Top trim B. Side trim C. Bottom trim Fresh Food Door D. Top trim E. Side trim F. Bottom trim G. Panel support brackets (4) H. 4-3/8" screws for support brackets (20) I. Grille support panel and screws ZKT48–8 screws J. Wood screws #6 1/2" flat-head screws ZKT48–30 screws This kit provides for the installation of 3/4" custom door and grille panels, using the standard full
GE ZIS48N, GE Monogram ® 48" Built-In Refrigerators Custom Options Guide and Installation Instructions With Custom Panel Dimensions and Trim Kit Installation Instructions Models: ZIS48N ZISW48D ZISB48D These Monogram built-in refrigerators are designed to be customized with decorator door and grille panels. Field installed panels are required. Factory installed trim will accommodate 1/4" thick custom panels or optional Lexan ® and Stainless Steel panel kits. Optional trim kits allow an even broader range of custom appearance options. Read this booklet carefully to accomplish the desired appearance and to insure a trouble free installa
GE ZIS48N, 12 Custom Panel Dimensions 48" Built-In Refrigerator ZISW48D (white dispenser) ZISB48D (black dispenser) • The ZKT48 trim kit provides for the installation of 3/4" custom door and grille panels, using the standard full- length handle. Cut panels to size and install. • For standard dispenser trim: Cut panels to size, rout the bottom of the upper freezer panel and the top of the lower freezer panel to allow placement of support brackets and install (see detail A). • For custom dispenser trim ZWCD2 kit must be used: Cut panels to size,
GE ZIS48N, DESIGN INFORMATION Design Information 48" Built-In Refrigerator Flush or Semi-Flush Enclosure Installations Side Panels Requirements: • Side panels are not required whenever the refrigerator is installed into an enclosure or between pantry and oven cabinets. • Side panels are required whenever the sides of the refrigerator are exposed. • Side panel sizes vary depending on the type of installation being made. To accomplish an attractive installation, you must: 1. Determine the need for side panels. 2. Determine side panel thickness. 3. Order matching side panels from the cabinet manufacturer. Be sure to provide the exact dimensions. True
45 ZKHTSS1 for 3/4" Panels Tubular Stainless Steel Handles For models with full width dispenser trim and 2 piece freezer panels: It is best that 2 people perform this step. • Carefully, lift the assembled panel to the case trim. Hold both panels so they do not twist the extrustion. • Insert the support bracket tabs into the bottom trim. • Push and hold the panel back against
GE ZIS48N, 8 Custom Panel Dimensions 48" Built-In Refrigerator Custom Door Panel Dimensions Using Trim Kit ZKT48 3/4" thick panel with standard handle Grille Panel height can vary to fill installation height. Installation Height Dimension A 83" 8-1/4" 83-1/2" 8-3/4" 84" 9-1/4" 84-1/2" 9-3/4" Important: Maintain 1-1/2" min. gap between top of doors and bottom of grille panel. ZIS48N (non-dispenser) • The ZKT48 trim kit provides for the installation of 3/4" custom door and grille panels, u
GE ZIS48N, 31 ZKT48 Trim Kit 3/4" Custom Panels Dimension B ZKT48–8-3/4" Dimension A ZKT48–6" Dimension C ZKT48–6" • Position and mark the location for the support brackets on the back side of the panels. Align all brackets flush with the end of the panels, with tabs protruding over the edge. • On the bottom of the upper panel, measure dimension A from the hinge side. • On the bottom of the lower panel, measure dimension B from the hinge side. • On the top of the lower panel, measure dimension C from the hinge side. • Secure all brackets with #4 screws provided. • Attach
GE ZIS48N, • Again, with both doors closed, check the location of the centerlines to be sure they are parallel to the edge of the door, and level with opposite door. • Drill 1/16" pilot hole through the panel until it starts into the aluminum extrusion. This will mark the matching location for drilling the clearance hole when assem- bling the handle, panel and extrusion. Note: Handle must be located 3/4" to 1-1/2" from edge of extrusion. ZKH1 Trim Kit (For 1/4" Panels) Support for Custom Handles Step 2 Locate position of handles Option 1 Installation • Slide custom panels into fresh food and freezer door frames. • Temporarily secure the new door extrusions to the d
GE ZIS48N, 39 ZKHSS1 for 1/4" Panels Tubular Stainless Steel Handles Step 2: Match Handle Extrusions to Handle • Cut a piece of corrugated to use as a pad to protect the panel finish. Use 1/2" thick section of plywood to protect flooring when drilling. • Place custom panels on the pad, appearance side down. Note: If panels are wood, be sure to note which end is the top so that wood grain is in the correct direction on both (or all 3) panels. • On the back side of the panel – at the handle side, measure and mark 1/4" below the top edge of the panel with a pencil. • Slip panels into new extrusion on the handle side of the panels. • Alig
24 ZKH1 Trim Kit (For 1/4" Panels) Support for Custom Handles OPTION 2 For dispenser model using full-width trim Step 1 Remove handles • Carefully remove the Phillips head screws from the door handle endcaps, top and bottom. • Open door to 90°. Remove the screws from the full-length aluminum handle of the freezer door. • Retain screws, discard handle and endcaps. Re
GE ZIS48N, 21 ZKH1 Trim Kit (For 1/4" Panels) Support for Custom Handles OPTION 1 For non-dispenser model or dispenser model using custom collar trim Step 1 Remove handles Kit contents Parts List: A. Fresh food door extrusion B. Freezer door extrusion for non- dispenser model and dispenser model using custom collar. (Option 1) C. Freezer door extrusion for dispenser model using full-width trim. (Option 2) D. Handle bracket for dispenser model using full-width trim. (Option 2) Tools and materials required: •#2 Phillips screwdriver •Drill and appropriate bits •Custom door panels •Custom handles •Safety glasses These instructions are divided into 2 options: Optio
DOWNLOAD |
GE PFE29 Refrigerator Owner's manual and installation instructions
PFE29 |
GE GTR10 Refrigerator Owner's manual and installation instructions
GTR10 |
GE 18, 19 Refrigerator Owner's manual and installation instructions
18, 19 |
GE PFSS6SKXSS Refrigerator Owner's manual & installation instructions
PFSS6SKXSS |
GE Profile GTR12HAX Refrigerator Dimensions and installation information
Profile GTR12HAX |
GE GTQ095PANR Refrigerator User and care manual
GTQ095PANR |
GE GSHS3KGZSS Refrigerator Energy manual
GSHS3KGZSS |
GE HTH18EBDCC Refrigerator Energy manual
HTH18EBDCC |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Equipex | 350-E | Operation manual | equipex/350-e-14G.pdf | 12 Feb 2024 | 12 | 2.98 Mb |
2 | JVC | CS-V424 | Instructions | jvc/cs-v424-B7B.pdf | 20 Aug 2023 | 2 | |
3 | BenQ | FP2081 | Operation & user’s manual | benq/fp2081-64Y.pdf | 10 Feb 2023 | 21 | 0.33 Mb |
4 | Philips | MCD170/58 | Operation & user’s manual | philips/mcd170-58-681.pdf | 26 Nov 2023 | 33 | 1.63 Mb |
5 | PowerBass | XMA-600D | Owner's manual | powerbass/xma-600d-7LT.pdf | 06 Mar 2024 | 24 | |
6 | Toshiba | SDP94DT | Owner's manual | toshiba/sdp94dt-Y8K.pdf | 13 Sep 2022 | 100 | 1.27 Mb |
GE
gGE Consumer Service TrainingTECHNICAL SERVICE GUIDEMODELS: PUB # 31-9023 3/99GE Profile Performance Series Top-Freezer CustomStyleREFRIGERATORTNX22PTNX22Btmtm
…
TNX22P(45 pages) |
Premier
MANUAL DE INSTRUCCIONES NEVERA VERTICAL NV-2350 ESTIMADO CLIENTE ¡Felicitaciones por su compra! Por favor lea cuidadosamente este manual, y guárdelo para su futura referencia. Si necesita soporte adicional, no dude en escribir a: [email protected] Pagina 1 DESCRIPCIÓN GENERAL 1. Congelador 2. Bandeja de agua 3. Embudo …
NV-2350(7 pages) |
LG
CAUTIONPLEASE READ CAREFULLY THE SAFETY PRECAUTIONS OF THIS BOOK BEFORE CHECKING OR OPERATING THE REFRIGERATOR. REFRIGERATORSERVICE MANUALRef. No.GR-L207TRAMODEL: GR-L208NN/GR-L248NN COLOR: TITANIUMhttp://biz.lgservice.comGR-L207TRA
…
GR-L208NN(118 pages) |
Summit
REFRIGERATORS REFRIGERATOR-FREEZERS FREEZERS MODELS: Refrigerators: ALR46W, ALR47B, BIAR402, BIAR405B Refrigerator-Freezers: ALRF48, ALRF49B, BIRF403, BIRF406B Freezers: ALFZ36, ALFZ37B, BIFZ404, BIFZ407B User Manual BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. Felix Storch, Inc. An …
ALRF49B(16 pages) |
GE
PUB # 31-9117 04/04MODEL SERIES:MonogramInverter Compressor Side-By-SideRefrigeratorsGEA01265GE Consumer & IndustrialTECHNICAL SERVICE GUIDEZIS360NRZIS420NRZIS480NRZIS_360DRZIS_420DRZIS_480DR
…
Monogram ZIS360NR(63 pages) |
Amana
Owner's ManualDishwasherKeep instructions for future reference.Be sure manual stays with dishwasher.Part No. 6 917311 AContentsImportant Safety Information ...................... 3Washing the Dishes ................................... 4Custom Features........................................ 6Water, Detergents and Rinse Aids .............. 7Dishwashing R …
Distinctions(24 pages) |
Ski-Doo Snowmobiles ALPINE VALMOMTSnowmobiles #J5F235 ALPINE VALMOMT, 30 |
NEC Microcontrollers 78K/0S SeriesMicrocontrollers #483197 78K/0S Series, 123 |
Hotron Kitchen Appliances HR50User Guide: Hotron HR50 (YW9956, Upd.15.12.2023) HR50, 2 |
Sony LCD TV KDL-32D3000Sony KDL-32D3000 Manual (Doc Type: LCD TV Operating instructions manual) KDL-32D3000, 132 |
Yamaha Offroad Vehicle YFM35FGWYFM35FGW Owner's manual - M76TLJ YFM35FGW, 155 |
Sennheiser Amplifier HDVA 600Sennheiser Amplifier HDVA 600 Instruction manual HDVA 600, 18 |
Angelo Po Dishwasher KD37Instructions for installation, use and maintenance manual for Angelo Po KD37 Dishwasher KD37, 36 |
TRANKVILE Bicycle AhoogaPDF Manual (@89S96E), TRANKVILE Ahooga Bicycle (Saturday 06-01-2024) Ahooga, 35 |
Umarex Measuring Instruments AirflowTest-Master Reader#549MPQ: AirflowTest-Master Reader Measuring Instruments Operation & user’s manual AirflowTest-Master Reader, 21 |
International Refrigeration Products Heat Pump WHP49230RHeat Pump Operation & user’s manual (International Refrigeration Products WHP49230R) WHP49230R, 19 |
Napoleon Indoor Fireplace NDX40NT-2Guide: Napoleon NDX40NT-2 (51PEL5, Upd.17/11/2023) NDX40NT-2, 112 |