Manualios.com

Clarity CCE203DAB Instruction Manual

Clarity CCE203DAB Manual Online:

4.35, 576 votes
Clarity CCE203DAB User Manual
Clarity CCE203DAB User Guide
Clarity CCE203DAB Online Manual

Text of Clarity CCE203DAB User Guide:

  • Clarity CCE203DAB, Page CONTENTS 01 Contents 0 Installation 0 Using the detachable front panel 0 Wiring Diagram 0 Operations 0 Radio Operations 1 CD/MP3 Operations 1 Mixed-CD Operations 1 1 USB Device Operations 1 Disc Notes 1 02 Safety instructions 3 5 6 7 07 Location and Function of Keys 8 General Operations 10 11 AUX in Operations 5 15 SD/MMC Card Operations 6 7 Trouble Shooting 18 Specifications RDS (Radio Data System) Operations 12 DAB Radio Operations 3Disc 4 4

  • Safety Instructions CAUTION: IMPORTANT SAFETY INSTRUCTIONS TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE ANY COVERS. NO USER-SERVICEABLE PARTS INSIDE, REFER ANY SERVICING TO QUALIFIED SERVICE PERSONNEL. Read and keep these instructions available for future reference. The unit must only be connected to a 12 Volt D.C. vehicle with a negative earth (ground) power supply. Ensure all wiring

  • Clarity CCE203DAB, Notes: - Choose the mounting location where the unit will not interfere with the normal driving function of the driver. - Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. - Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. - Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. - Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a

  • Clarity CCE203DAB, 7. Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables. 8. Slide the unit into the sleeve until it locks into place. 9. To further secure the unit, use the supplied metal strap to secure the back of the unit in place. Use the supplied hardware (Hex Nut (M5mm) and Spring Washer) to attach one end of the strap to the mounting bolt on the back of the unit. If necessary, bend the metal strap to fit your vehicle's mounting area. Then use the supplied hardware (Tapping Screw (5x25m

  • Clarity CCE203DAB, If your vehicle is a Nissan, Toyota, follow this mounting instruction. Use the screw holes marked T (Toyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle. Fasten the unit to the factory radio mounting brackets. Align the screw holes on the bracket with the screw holes on the unit, and then tighten the screws (5x5mm) on each side. the outer trim ring, sleeve and the metal strap are not used for method B installation. Note: 2. DIN REAR-MOUNT (Method B) Using The Detachable Front Panel 2 Grasp the right side of the front

  • Clarity CCE203DAB, Wiring Diagram L R FUSE ISO CONNECTOR ISO connector: Part A: A1: A2: A3: A4: A5: A6: A7: A8: Part B: B1: B2: B3: B4: B5: B6: B7: B8: No Connect No Connect No Connect Battery B+ (Yellow) Antenna (Blue) No Connect Accessory (Red) Ground B- (Black) Rear Right + (Violet) Rear Right - (Violet/Black) FrontRight+(Grey) Front Right - (Grey/Black) Front Left + (White) Front Left - (White/Black) Rear Left + (Green) Rear Left - (Green/Black) WHITE WHITE / BLACK GREEN GREEN / BLACK VIOLET VIOLET / BLACK GREY GREY / BLACK FRONT 4ohm LEFT SPEAKER REAR 4ohm RIGHT SPEAKER TO MEMORY B+ GND B- ACC B+ BLUE RED YELLOW FRONT 4ohm REAR 4ohm BLACK TO ANTENNA DAB Ante

  • P1 EQ AF PTYDISP TA MOD BND M1 M2 M3 M4 M5 M6 AMS SCN RPT SHF AUX PUSH SEL REG CCE203DAB Operations Location and function of keys Front panel : The car radio after removing the front panel: (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) Power on/off( ) Button LCD display Encoder Volume Control/ SEL Button Open ( ) Button Disc slot Eject( )key SD/MMC Memory Card Slot USB Port

  • Reset the unit Power on/off Sound adjustment System setup menu The RESET button is to be activated for the following reasons: - Initial installation of the unit when all wiring is completed. - All the function buttons do not operate. - Error symbol on the display. 1.Turn off the unit power. 2.Press the ( ) button to flip down the front panel and remove it, then press the button with a ballpoint p

  • Clarity CCE203DAB, few seconds before switching back to the current station that was broadcast initially. If “PI MUTE” is selected, the radio will not broadcast the new station that is received. This function allows you to set the duration after which the automatic search for traffic information or a station with an identical PI should be carried out. - The automatic search will take place after 90 seconds. The automatic search will take place after 30 seconds. Any alternative frequency (AF) with a different PI or which does not broadcast an RDS signal that is strong enough will normally be masked when the PI is checked while the unit searches for an alter

  • Clarity CCE203DAB, Radio Operations Note: - When receiving a non RDS station: Note: Note: 1. When a call comes in 2. When the call ends If the unit does not receive CT or PTY information, the display shows “NO CLOCK” or “PTY NONE”. In radio mode:NO CLOCK->PTY NONE-> PS NONE ->FREQUENCY -> In CD/USB/SD/MMC mode: NO CLOCK -> PTY NONE -> FREQUENCY -> PS NONE -> Track number /Running time or other information The selected information is displayed for 5 seconds, then the radio goes back to the first display mode after 5 seconds. The audio system automatically mutes whenever a telephone call comes in. The function will not work if a cable is not

  • Clarity CCE203DAB, preset station. If the field strength level is more than the threshold level, the radio will hold at this preset station for 5 seconds with sound output, then go to next station until all 6 FM stations are scanned, finally the radio will play at the preset station where scanning started. The preset station number on the LCD will flash during the process. Press the again to stop preset scan. AMS - Auto store: Press the button for more than 2 seconds to start auto store. The radio will scan from the lowest frequency, and automatically store the 6 strongest stations into the preset memories. When auto store is complete, the radio will start a preset scan of the 6 stations which it

  • Clarity CCE203DAB, HINT: MUSIC PTY GROUP preset number buttons 1-6 Preset Music PTY Group number SPEECH PTY GROUP preset numbered buttons Preset Speech PTY Group number TA TA TA When you choose , the correspond to the following programs: 1 POP M, ROCK M 2 EASY M, LIGHT M 3 CLASSICS, OTHER M 4 JAZZ, COUNTRY 5 NATION M (national music), OLDIES 6FOLKM When you select the , the is shared as follows: 1 NEWS, AFFAIRS, INFO 2 SPORT, EDUCATE, DRAMA 3 CULTURE, SCIENCE, VARIED 4 WEATHER, FINANCE, CHILDREN 5 SOCIAL, RELIGION, PHONE IN 6 TRAVEL,LEISURE, DOCUMENT When you select a program ty

  • Clarity CCE203DAB, To store / recall a preset radio stations Information display To clear the DAB station memory You can store up to a total of 18 DAB radio stations in the memory. - Select a band (if needed) - Select a station by or buttons. -Pressandholdapresetbutton( - )for at least 2 seconds. - Select a band (if needed). -Pressapresetbutton( - )brieflyto recall the stored station. Press the button repeatedly to display as follows: Component name -> Clock -> DLS message (up to 128 character, 20 seconds time out) - > Program type (10 seconds tim

  • Clarity CCE203DAB, Go to the previous / next directory During MP3 playback, press the or button to select the previous or next directory. If the MP3 disc does not contain any directories, this function will not be available. 56 Introduction playback Repeat playback Random playback You can play the beginning of every track for 10 seconds in sequence. - In CD/MP3 file playback, briefly press the button to play the first 10 seconds of each track. Press it again to stop scanning and play the current track. -In CD/MP3 files playback, briefly press the button to Press again to stop repeat playback and resume normal playback. - In CD/M

  • The is equipped with aCD/MP3 car radio USB port on the front panel of the unit, you can connect a USB stick through the USB port. When you insert a USB stick through the port, the unit will search for the MP3 files and start to play them automatically. If you insert a disc into the disc slot while reading the USB stick, the unit will play the disc. You can pres

  • Clarity CCE203DAB, - Do not warp discs. - A disc should always be kept in its case when not in use to prevent from damage. - Do not place discs in the following places: 1. Direct sunlight. 2. Dirty, dusty and damp areas. 3. Near car heaters. 4. On the seats or dashboard. Use a dry soft cloth to wipe the surface. If the disc is quite dirty, Use a soft cloth slightly moistures with isopropyl (rubbing) alcohol. Never use solvents such as benzene, thinner or conventional record cleaners as they may the surface of the disc. A disc may become somewhat scratched (although not enough to make it unusable) depending on

  • Clarity CCE203DAB, Trouble Shooting Symptom Cause Solution No power The car ignition switch have not turn on. If the power supply is connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse has been blown. Replace a new one. Presence of CD disc inside the player. Remove the disc from the player, and insert a new one. Disc can not be loaded or ejected. Inserting the disc in reverse direction. Insert the CD with the label facing upward. The surface of CD is extremely dirty or has been scraped. Clean the disc or try to replace a new one. Temperature inside the car is t

  • Clarity CCE203DAB, 1. GENERAL 2. CD PLAYER 3. RADIO FM Power Supply Requirements DC 12 Volts, Negative Ground Chassis Dimensions 178(W)x160(D)x 50(H) mm Tone Controls -Bass(at100Hz) ±10dB - Treble (at 10KHz) ±10 dB 4x40watts Power 15 Ampere (max.) Signal to Noise Ratio >55dB Channel Separation >40dB Frequency Response 40Hz-18KHz Frequency Range 87.5 - 108 MHz IF 10.7 MHz Sensitivity (S/N=30dB) 4µV Stereo Separation Maximum power output Discs/files played CD-DA,CD-R/RW/MP3 Frequency Range 174 - 240 MHz Signal to Noise Ratio 55dB(mono) 30 dB (65dBu, 1KHz) Frequency Range 522 - 1620 KHz IF 450 KHz Note: Design

Related Products and Documents (Radio):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Hypertherm powermax1650 Service manual hypertherm/powermax1650-A4D.pdf 11 Sep 2022 73
2 Ace 3035466 (AC-6180) Owner's manual ace/3035466-ac-6180-K47.pdf 21 Feb 2024 24 0.32 Mb
3 Kramer VS-3232D Operation & user’s manual kramer/vs-3232d-6J3.pdf 13 Aug 2023 51
4 Delta 21925 Series Installation manual delta/21925-series-6D1.pdf 04 Feb 2024 6 0.64 Mb
5 Top Dawg Electronics TDBTS-01 Instruction manual top-dawg-electronics/tdbts-01-UPH.pdf 24 Sep 2023 5
6 VideoWave n-E4E Operation & user’s manual videowave/n-e4e-QT2.pdf 18 Jul 2023 73

Similar Resources:

  • PNI

    ESCORT HP 6500

    (7 pages)
    1、IntroductionThank you for your choose and buy the Nanfone CB Radio. In order to make your CB Radio to use in the best condition, please read this manual in detail.PNI Escort HP 6500 is a small, simple operation and convenient vehicle CB Radio which has good performance.Feature:Up/down keys on the microphoneScan channelLCD displayAuto A …
  • Streamit

    SIR80

    (24 pages)
    STREAMIT INTERNET RADIO User’s manual May 2008 Version 1.0 i Streamit Internet Radio SIR series of devices User’s manual ENGLISH …
  • Silvercrest

    KH 2281

    (14 pages)
    KITCHEN RADIOOperating instructions6KITCHEN RADIOKOMPERNASS GMBH · BURGSTRASSE 21 · D-44867 BOCHUMwww.kompernass.comID-Nr.: KH2281-07/08-V1KH 2281CV_KH2281_AR5027_LB6 15.07.2008 9:00 Uhr Seite 1 …
  • Silvercrest

    SWEP 500 A1

    (97 pages)
    MULTI-BAND RADIO SWEP 500 A1IAN 94111 MULTI-BAND RADIOOperating instructionsΔΕΚΤΗΣ ΠΑΓΚΟΣΜΙΟΥ ΛΗΨΕΩΣΟδηүίες χρήσης WELTEMPFÄNGERBedienungsanleitungCV_94111_SWEP500A1_GB_IE_CY.indd 3CV_94111_SWEP500A1_GB_IE_CY.indd 3 04.12.13 08:0304.12.13 08:03 …
  • Vertex Standard

    VX-2500

    (2 pages)
    VHF/UHF Mobile RadiosVX-2500 SERIES POWER OUTPUT 25 W 128 CHANNEL (10 GROUPS) CAPACITY INVERTIBLE ALPHA NUMERIC DISPLAY (14 SEGMENTS x 8 DIGITS) RUGGED DIE-CAST CONSTRUCTION CTCSS ENCODER/ DECODER DUAL 2-TONE DECODING DCS ENCODER/ DECODER DTMF ANI ENCODER DTMF ANI ID DISPLAY DTMF PAGING VERSATILE SCANNING …
  • IPMobileNet

    F32700N25

    (32 pages)
    IPSeries F32700N25 Fixed Radio Product Owner‟s Manual Date Released: March 16, 2011 Document #: 516-80618-POM Rev B Copyright 2011 IPMobileNet, LLC. 1221 East Dyer Road, Suite # 250 Santa Ana CA 92705 Voice: (714) 434 6019  Fax: (714) 434 6019 …

Comments, Questions and Opinions: