Manualios.com

Fujitsu Frenic Eco FRN-F1 Starting Manual

Fujitsu Frenic Eco FRN-F1 Manual Online:

3.2, 1672 votes
Fujitsu Frenic Eco FRN-F1 User Manual
Fujitsu Frenic Eco FRN-F1 User Guide
Fujitsu Frenic Eco FRN-F1 Online Manual

Text of Fujitsu Frenic Eco FRN-F1 User Guide:

  • Fujitsu Frenic Eco FRN-F1, Chapter 4: Keys and LED on the Keypad 9 FRN - F1 4. OPERATION USING THE KEYPAD As shown in the figure at right, the keypad consists of a four-digit LED monitor, 5 LED indicators, and six keys. The keypad allows you to start and stop the motor, monitor running status, and switch to the menu mode. In the menu mode, you may set the function code data, monitor I/O signal states, maintenance information, and alarm information. Item Monitor, LED indicators and Keys Functions LED Monitor Four-digit,

  • Fujitsu Frenic Eco FRN-F1, Chapter 6: Function Codes 16 FRN - F1 F03 Maximum Frequency Sets the maximum frequency to drive the motor. Setting the frequency out of the range rated for the equipment driven by the inverter may cause damage or a dangerous situation. Set a maximum frequency appropriate for the equipment. The inverter can easily set high-speed operation. When changing the speed setting, carefully check the specifications of motors or equipment beforehand. Otherwise injuries could occur. If you modify the data of F03 to apply a higher drive frequency, concurrently change the data of F15 fo

  • Chapter 7: Protective Functions 22 FRN - F1 7. PROTECTIVE FUNCTIONS 7.1 Protection / Maintenance Function (Parameter H98) Possibility to enable or disable of: n Automatic lowe

  • Fujitsu Frenic Eco FRN-F1, Chapter 5: Quick Starting Commissioning 10 FRN - F1 5. QUICK STARTING COMMISSIONING 5.1 Running the Motor for a Test 5.1.1 Inspection and preparation prior to powering on Check the following prior to starting powering on. (1) Check if connection is correct. Especially check if the power wires are connected to the inverter input terminals L1/R, L2/S and L3/T, and output terminals U, V and W respectively and that the grounding wires are connected to

  • Chapter 8: Specifications and External Dimensions 26 FRN - F1 8.1.2 Semi standard – IP54 with integral EMC filter and DCR Item Specifications Type (FRN???F1L-4E) 0.75 1.5 2.2 3.7 5.5 7.5 11 15

  • Fujitsu Frenic Eco FRN-F1, Chapter 8: Specifications and External Dimensions 24 FRN - F1 8. SPECIFICATIONS AND EXTERNAL DIMENSIONS 8.1 Inverter Specifications 8.1.1 Standard Model – IP20 / IP00 Note: A box ( o ) in the above table replaces J depending on the shipping destination.

  • Fujitsu Frenic Eco FRN-F1, Chapter 1: Safety Information and Conformity to Standards 1 FRN - F1 1. SAFETY INFORMATION AND CONFORMITY TO STANDARDS 1.1 Safety Information Read this manual thoroughly before proceeding with installation, connections (wiring), operation, or maintenance and inspection. Ensure you have sound knowledge of the device and familiarize yourself with all safety information and precautions

  • Fujitsu Frenic Eco FRN-F1, Chapter 6: Function Codes 13 FRN - F1 F27 Tone 0~3 0 F29 Selection 0 / 1 0 F30 Level 0~200% 100% F31 Analog Output (FMA) Function 0 ~ 16 0 F33 Pulsrate 25 ~ 6000p/s 1440p/s F34 Level 0% / 1 ~ 200% 0% F35 FMP Terminal Function 0 ~ 16 0 F37 Load selection / Auto torque boost/ Auto energy saving operation 0 ~ 5 1 17 F43 Selection 0 ~ 2 0 F44 Current limiter Level 20 ~ 120% I N Mot. 110% The shaded function codes are applicable to the quick setup E codes : Extension Terminal functions Code Name Setting Ra

  • Fujitsu Frenic Eco FRN-F1, Chapter 3: Electrical Installation 8 FRN - F1 3.2.1 Control Terminals Connection Digital inputs and outputs can be operated both in NPN (sink) and PNP (source) logic. a) DIGITAL INPUTS: Refer to the user's manual MEH456 for connection examples. SW1 SINK SW1 SOURCE The switch SW1 located on the control board defines the logic used for digital inputs. Factory default setting is source.

  • Fujitsu Frenic Eco FRN-F1, Chapter 1: Safety Information and Conformity to Standards 3 FRN - F1 1.2 Conformity to Standards 1.2.1 .Conformity to European Standards The CE Approved on Fuji products indicates that they comply with the essential requirements of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC issued by the Council of the European Communities and the Low Voltage Directiv

  • Fujitsu Frenic Eco FRN-F1, 9 Chapter : Options 30 FRN - F1 9. OPTIONS Name of option Function and application DC reactors (DCRE) A DCRE is mainly used for power supply normalization and for supplied power-factor reformation (for reducing harmonic components). Use a DCRE when: - the capacity of a power supply transformer exceeds 500 kVA and is 10 times or more than the rated inverter capacity. In this case, the percentage- reactance of the power source decreases, and harmonic components an

  • Fujitsu Frenic Eco FRN-F1, Chapter 8: Specifications and External Dimensions 25 FRN - F1 Note A box ( o ) in the above table replaces J depending on the shipping destination.

  • Fujitsu Frenic Eco FRN-F1, Chapter 6: Function Codes 14 FRN - F1 C08 Frequency 4 0.00Hz C09 Frequency 5 0.00Hz C10 Frequency 6 0.00Hz C11 Frequency 7 0.00Hz C30 Frequency command 2 0 ~ 3 / 5 / 7 2 14 C32 Terminal 12 0.00 ~ 200.00 % 100.00% C33 Signal filter 0.00 ~ 5.00s 0.05s C34 Analog input gain adjustment Gain base point 0.00 ~ 100.00% 100% C37 Terminal 1 0.00 ~ 200.00 % 0.00Hz C38 Signal filter 0.00 ~ 5.00

  • Fujitsu Frenic Eco FRN-F1, Chapter 7: Protective Functions 23 FRN - F1 Note that, however, the inverter turns on (OH) and (LIFE) signals on the transistor output terminals whenever the DC fan lock is detected regardless your selection. If control of the cooling fan is enabled (H06 = 1) the fan will stop depending on operating condition of the inverter. In this case, the DC fan lock detection feature determines this failure for a normal operation state (e.g.; the fan is normally stopped by the stop fan

  • Fujitsu Frenic Eco FRN-F1, Chapter 2: Mechanical Installation 5 FRN - F1 For inverters with a capacity of 30 kW or below (for others please refer to user's manual chapter 2). For mounting the covers, please refer to next snapshots and follow removing instructions in the opposite way.

  • II FRN - F1 8.2 External Dimensions………………………………………………………………………………………………… 27 8.2.1 Inverter Standard Models........................................

  • Fujitsu Frenic Eco FRN-F1, Chapter 8: Specifications and External Dimensions 27 FRN - F1 8.2 External Dimensions 8.2.1 Inverter Standard Models FRN0.75F1S-4 to FRN5.5F1S-4 Unit: mm FRN7.5F1S-4 to FRN30F1S-4 Note: A box ( o ) is for the area code Unit: mm FRN37F1S-4 to FRN500F1S-4 Unit: mm

  • Fujitsu Frenic Eco FRN-F1, Fuji Electric GmbH . Goethering 58 . 63067 Offenbach/Main . Germany Tel.: +49 (0)69 669029-0 . Fax +49 (0)69 669029-58 . [email protected] . www.fujielectric.de STARTING GUIDE FRENIC Eco . FRN-F1 Fuji Electric frequency inverter for HVAC applications 3-phase 400V 0.75 – 500kW

Related Products and Documents (Inverter):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Philips 374188616 Specifications philips/374188616-6GS.pdf 20 Aug 2022 2 0.96 Mb
2 Presto 8702 Instructions presto/8702-1Q6.pdf 09 Jan 2024 3
3 Philips BDP9000 Operation & user’s manual philips/bdp9000-8MT.pdf 10 Jul 2022 69 5.12 Mb
4 Sony SRS-BTX300 Startup manual sony/srs-btx300-S79.pdf 19 Jan 2023 2 3.75 Mb
5 Haier BD-519H User manual manual haier/bd-519h-31L.pdf 10 Sep 2022 63 4.35 Mb
6 John Deere 440 Liquifire Operator's manual john-deere/440-liquifire-F32.pdf 15 Sep 2022 38

Similar Resources:

  • Siemens

    SINAMICS G120

    (30 pages)
    SINAMICS G120 Control Units CU240E Getting Started FW 3.1 10/2007 A5E01301680B AA Warnings and Cautions 1 Installation 2 Check List 3 Commissioning 4 Diagnostics A …
  • Kaco

    blueplanet 3.0 TL3 M2 WM OD IIG0

    (93 pages)
    ManualnEnglish translation of German originalKACO blueplanet 3.0 TL3KACO blueplanet 4.0 TL3KACO blueplanet 5.0 TL3KACO blueplanet 6.5 TL3KACO blueplanet 7.5 TL3KACO blueplanet 8.6 TL3KACO blueplanet 9.0 TL3KACO blueplanet 10.0 TL3These instructions form part of the product and must be carefully read, observed and stored in a place which is freely accessible …
  • sol-ark

    12K

    (49 pages)
    October 21st, 2021 1 SPEC SHEET ........................................................................................................................................................................................ 5 WIRE GAUGE GUIDE (COPPER) ................................................................................. …
  • Ozone Solutions

    TG Series

    (20 pages)
    TG SERIESWATER COOLED OZONE GENERATORMODEL: TG-75, TG-150, TG-300, TG-450, TG-600INSTALLATION & OPERATIONS MANUAL451 Black Forest Road / Hull, Iowa 51239 USAP 712.439.6880 / F 712.439.6733 …
  • Westinghouse

    WGen9500

    (81 pages)
    USER MANUALWGen9500 Portable Generator Gasoline: 9500 Running Watts | 12500 Peak Watts DO NOT RETURN THIS PRODUCT TO THE STORE If you have questions or need assistance, please call customer service at 855-944-3571. …
  • Growatt

    Growatt 2500MTL-S

    (30 pages)
    GR-UM-045-A-02Growatt 2500MTL-SGrowatt 3000MTL-Growatt 4200MTL-Growatt 5000MTL-Growatt 5500MTL-SGrowatt 3600MTL-SSSSInstallation & Operation ManualShenzhen Growatt New Energy Technology CO.,LTDBuilding B, Jiayu Industrial Park, #28, GuangHui Road,Shiyan Street, Baoan District, Shenzhen, P.R.ChinaT 0755-29515888 F 0755-274 …

Comments, Questions and Opinions: