MicroNet SP5101 Operation & User’s Manual

Text of MicroNet SP5101 User Guide:

• 72 6.6 [commit] command Save any changes after configuring the SIP Phone SP5101. 6.7 [ping] command Command ping can test which the IP address is reachable or not. Usage: ping “IP address” The message will display packets transmitting condition or no answer from the IP address. 6.8 [time] command When SIP Phone SP5101 enable SNTP

• 28 3.3.6 PPPoE ID It could support the number or character typing in this mode. Password For the protecting policy, LCD will use the asterisk to replace the info showing. For the password modify displaying, the LCD will clean all the asterisks and showing the cursor as following: → OK → → OK → Reconne

• 22 entry added, show all the entries in the phone book to verify by users. If users press the button, the flow will be just like the actions in the phone book → → → → → M4 → → OK → ● Delete → → → → → M4 → → M4 → → OK → → OK → → 3.1.2 Dialed Call

• MicroNet SP5101, 45 (B) Network Configuration: After selecting network connection mode, user has to input related network parameters. (1) Static IP: User has to input IP, subnet mask, default gateway, and DNS server address. (2) PPPoE: User has to input PPPoE connection user name and password.

• MicroNet SP5101, 29 Server IP To enter SNTP server IP address. It supports the number typing and Domain typing. Time Zone Pressing the M1 for decreasing and M4 for increasing the zone value. The button will save the changed. 3.4 SIP setting All the menu operations are as same as the Networking setting. ¾ Proxy Setting  Proxy IP  Proxy Port  OutPx IP  OutPx Port ¾ User Setting  ID  Password  Phone Num  Local Port 3.4.1

• MicroNet SP5101, 24 This is allowed the same number with the different name. For the name of the incoming call displaying, the phone set will show up the latest record configured by users. This isn’t permitted for the empty info about the name in this mode. If users press the button without any info for the name, the LCD will show as following and return to the New Entry table after a few seconds: → B Input Number After users enter the valid name for the New Entry, the LCD will show as following and it only supports the number typing in

• MicroNet SP5101, 5 1. INTRODUCTION The Micronet SP5101 VoIP desktop telephone highly integrates DSP/codec system-on-chip solutions to provide the industry’s highest voice quality. For ease-of-use functionality, SP5101 provides well compatibility with many well-known IP-PBX, and many user-friendly feature buttons of conference, call pick up, transfer, Redial, Hold …etc. The simple operation and configuration are most suitable for residential, SOHO, and enterprise applications. 1.1 Packet Content Before you start installing the device, verify the following items are in the

• MicroNet SP5101, 32 3.5.1 Alarm Setting There are some definitions for the Alarm clock, please check out the detail as following: If the alarm clock had been set and the time is up: z The phone will be ring in the IDLE and MENU state only. z If the phone isn’t in the IDLE or MENU state, the phone will ring while the state back to the IDLE or MENU. z If the state don’t return to the IDLE or MENU for 30 minutes, the clock will cancel and don’t ring the phone. z Ringing the phone every 20 seconds. z For the ringing tone, depends on the ring melody setting. z St

• MicroNet SP5101, 63 (2) Software Upgrade - Download Mode: Select download method as TFTP or FTP - TFTP/FTP Server IP Address: Set TFTP server IP address - FTP Login: Set FTP login name and password - Target File name: Set file name prepared to upgrade - Target File Type: Select which sector of SIP Phone to upgrade Note: After upgrade Application, please remember to execute Flash Clean, which will clean all configurations become factory values except Network settings..

• 26 3.3 Networking Setting ¾ IP Mode  Fixed DHCP PPPoE ¾ IP Address ¾ Net Mask ¾ Default GW ¾ DNS Setting  Primary DNS  Second DNS ¾ PPPoE  ID  Password  Reconnect  SNTP ¾ SNTP  Server IP  Time Zone  Mode 3.3.1 IP Mode Press the M1 or M4 button to select the IP mode. 3.3.2 IP Address Enter IP addre

• MicroNet SP5101, 75 4. –reboot: Select enable or disable this function. If user enables this function, after PPPoE disconnected, SIP Phone will automatically reboot to re-connect, and after reboot, if SIP Phone still can’t connect with server, SIP Phone will keep trying to connect. On the other hand, if user disables this function, SIP Phone won’t reboot and keep trying to connect. (pppoe –reboot 0/1) 5. –echo: to set PPPoE send echo request function or not. Under some ISP sending echo request will cause abnormal behavior for LAN Phon

• MicroNet SP5101, 81 tone, rbt: ring back tone, bt: busy tone, dt: dial tone). This parameter should be accompanied with tone type. 2. -ring: To set RING tone value. The played tone type, when Phone ha incoming call. 3. -rbt: To set Ring Back Tone value. The played tone type, when Phone dials out a call. 4. -bt: To set Busy Tone value. The played tone type, when Phone dials to a destination that is busy. 5. -dt: To set Dial Tone value. The played tone type, when hook off the Phone. 6.18 [tos] command TOS/DiffServ (DS) priority function can discriminate the Differen

• MicroNet SP5101, 25 Users could press the button to select the action in the view mode. If there is no any entry for the phone book, LCD will show the massage as following: Dial Out Press on specific phone book entry, phone will be off-hook and dial out automatically. Modify Entry Here user can modify name and number of existed phone book data. Delete Entry → OK → Detail Press to see detail name and number of this phone book entry. 3.2.3 Search Entry This mode could support the numbers or characters typing. If the entered name couldn’t be matched with the existed records, on LCD will show the first e

• MicroNet SP5101, 83 z drop: Enable or disable drop function. If this function is enabled, Gateway will drop prefix number on incoming call. z insert: Set which digit to insert on incoming call. Example: prefix -add prefix 100 drop 1 insert 2000 2. -modify: Modify a rule to drop or insert prefix digits of incoming call. Example: prefix –modify 100 drop 0 insert 200 3. -delete: Delete a rule to drop or insert prefix digits of incoming call. Example: prefix –delete modify 100 drop 0 insert 200 6.20 [rom] command 1. -print: show all current configurations and version information. 2. -ap

• MicroNet SP5101, 71 6.3 [debug] command This command is for engineers to debug system of SIP Phone SP5101. User can add debug flag via command debug –add “debug flags”, and then start debug function via command debug –open. When SIP Phone SP5101 is working on screen will display related debug messages. Most frequently used debug flag are “sip”, “fsm”, “msg”…etc. 6.4 [reboot] command After typing commit command, type reboot to restart the SIP Phone SP5101. 6.5 [pbook] command SIP Phone SP5101 can support 90 phone book data. 1. -print: display phone book data. User can print all data in phone book by command (pbook –print). 2. -add: add a new

• MicroNet SP5101, 79 6.15 [line] command 1. –print: display all current configurations. 2. –fwd: set forward function. There are 3 selections in Forward type, user must select under which condition to forward calls. 6.15.1 Busy Forward When SIP-Phone is in busy status, the incoming call will be forwarded to the assigned phone number. 6.15.2 No Response When SIP-Phone hasn’t been picked up for around 10 seconds, the incoming call will be forwarded to the assigned phone number. 6.15.3 Unconditional It is included the above t

• MicroNet SP5101, 15 2.7.7 LCD Display for Incoming Call state When it received incoming call, it will show incoming call display name and Line number 2.7.8 LCD Display in CONNECTED state During the talking state and running the timer During the talking state and running the timer The timer will still go on while the mute function was enabled during the conversation. Transfer action during the call. Hold the established call. Parking the call. Enable the conference function and start the timer from the beginning. 2.7.9 LCD Display in Call Waiting state Under conversation and LPSP5101 received incoming call. LCD of LPSP5101 will display incomi

• MicroNet SP5101, 80 6.16 [voice] command The voice command is associated with the voice codec setting information. 1. -print: display voice codec information and configuration. 2. -send: three voice packet size can be configured as 20 ms, 40 ms or 60 ms.(only 30 and 60 ms for G..723.1) 3. -priority: set codecs priority in order. Please notice that user can set from 1 to 5 codecs as their need, for example, voice –priority g723 or voice –priority g729 711a g711u means SIP Phone can support only one codec or four codecs. 4. -volume: There are three types can be

• MicroNet SP5101, 17 cursor will be blinking every 500ms just like the example as above: → → If the users enter the incorrect info, the LCD will show as following: 2.8 Editing Display a Cursor Under the characters or digits, the cursor will be displayed and the characters or digits will be blinking. It was shown as “_” with the LCD showing. Users could press the right or left arrow keys to make the cursor move to the right or left side. The blinking time for the on and off will be 500ms. b Insert the characters or numbers All the characters

• MicroNet SP5101, 70 Note: 1. A fter user enter SIP Phone configuration via telnet, please use login: ”root”, password: null, press enter to enter command lines. 2. If user forget login password, please contact with your distributor, we will generate one new password according to LAN Phone’s MAC address. Please login with “mac” and this new password. 3. User must input lower-case command, but contents of configurations such as SIP alias or user name etc, user can set as capital case. 4. A fter any change of configurati

• MicroNet SP5101, 68 5.6 Reboot Press reboot will reset SIP Phone. Note: To execute reboot via web browser, SIP Phone will automatically save all data before reboot. To execute reboot via TELNET command, please remember to do Commit Data before Reboot System.

• 40 5. Web Administration 5.1 Factory Default DESCRIPTION DEFAULT VALUE IP 10.1.1.3 Net Mask: 255.255.0.0 Default Gateway: 192.168.1.254 SIP Proxy: 10.1.1.2 SIP account 1001 SIP Port: 5060 Proxy Port: 5060 RTP Port: 16384 Digit Timeout: 5s Call waiting: Off Call transfer On 5.2 Configuring the SIP Phone through Web Pages

• MicroNet SP5101, 52 5.4.2 SIP Configuration (1) SIP Main Configuration - Primary Proxy Address and port: If user select Proxy mode in item A, please input Primary Proxy address and signaling port of Proxy. - Secondary Proxy Address and port: User can also input secondary Proxy server and port for backup. - Outbound Proxy Address and port: User can input outbound Proxy and port if necessary. - Phone Number: Registering Phone number of SIP Phone. - Registering Account Name and password: If Proxy server nee

• MicroNet SP5101, 76 6.12 [sysconf] command 1. -print: display all current configurations. 2. -idtime: set the duration(in second) of two pressed digits in dial mode as timed out. If after the duration user hasn’t pressed next number, SIP Phone will dial out all number pressed. 3. -keypad: set DTMF type .User can select DTMF type SIP Phone receive and transmit.(sysconf –keypad 0/1 , 0 for in band ,1 for RFC2833.) 4. -2833type: change RFC2833 Payload type. 5. -eod: select end of dialing key, e.g. set end of dial key as “＊” button , after finished pres

• MicroNet SP5101, 11 2.4 Keys with “ABC” character mode Users could enter the characters with the uppercase in this mode. The key could only input the special symbols and press more times to pick up the symbols you want. If users press two times on the key , the input character will be E. Key Characters with uppercase in “ABC” input method S33 S30 A B C S28 D E F S32 G H I S23 J K L S18 M N O S29 P Q R S S10 T U V S11 W X Y Z * S04 S17 Space S12 Input method switch key

• MicroNet SP5101, 27 3.3.3 Net Mask All the operation is just like the IP Address configuring. It will be shown as following from the LCD: 3.3.4 Default GW All the operation is just like the IP Address configuring. It will be shown as following from the LCD: If users input the invalid value for the IP address, Net Mask or Default Gateway, LCD will show as following and return to the original setting of this configuration table: 3.3.5 DNS Setting Primary DNS It supports

Related Products and Documents (IP Phone):

Comparable Devices:

Similar Resources:

• Avaya J129 (4 pages) Avaya IP Office VM Pro Voicemail on a J129 Phone User ManualSYRACUSE1 Dupli Park Drive, 5th FloorSyracuse NY 13204Tel: 315-671-6200Fax: 315-671-0080HOLLAND PATENT9560 Main StreetHolland Patent NY 13354Tel: 315-624-2000Fax: 315-624-0288 …

• Panasonic KX-TDA0350 (14 pages) Document Version: 2006-07IP Softphone Edition of PC Phone SoftwareQuick Reference Guidefor IP SoftphoneModel No. KX-TDA0350Thank you for purchasing the Panasonic PC Phone Software, KX-TDA0350.Please read this manual before using this product and save for future use.This manual is designed to provide instructions for installing the IP Softphone software on yo …

• Fanvil BW210 (53 pages) BW210 VoIP Phone Corporate Headquarters Fanvil Technology Co., Ltd Address: Unit 4A, Building NO.7, aTian An Industrial Park, Nanshan sdistrict,Shenzhen P.R.China Web Site: www. Fanvil.com Tel: +86 755 26402199 Fax: +86 755 26505858 User Manual Version: V1.7.18.17 Oct 23 2008 © …

• Topcom SOLOGIC B921 (340 pages) SOLOGIC B921 USER GUIDE / HANDLEIDING / MANUEL D’UTILISATEURBEDIENUNGSANLEITUNG / MANUAL DE USUARIOBRUKSANVISNING / MANUALE D’USOMANUAL DO UTILIZADOR / UŽIVATELSKÁ PÍRUKA  / INSTRUKCJA OBSUGIV 1.0 - 05/11 …

• Alcatel-Lucent 8078s Bluetooth Premium (71 pages) OpenTouch® Suite for MLE 8078s Premium Deskphone 8068s Premium Deskphone 8058s Premium Deskphone 8028s Premium Deskphone User Manual 8AL90339ENAAed01-1712 …

• 3Com 3500 (92 pages) i Table of Contents Conventions ··············································································································································· 1 Related Documentation········· …

Comments, Questions and Opinions: