Manualios.com

ESTeem 192C Operation & User’s Manual

ESTeem 192C Manual Online:

4.3, 1018 votes
ESTeem 192C User Manual
ESTeem 192C User Guide
ESTeem 192C Online Manual

Text of ESTeem 192C User Guide:

  • ESTeem 192C, CHAPTER 5 RS-232C/422/485 INTERFACING Revised: 8 Oct 03 5-1 EST P/N AA104 DTE vs. DCE The ESTeem is configured as a Data Communication Equipment (DCE) device. The following signals are available at the RS-232C connector located at the rear of the unit. Pin Description --------------------------------------------------------------------- 1 FG Shield Ground 2 TXD Transmit Data (Input) 3 RXD Receive Data (Output) DCE 4 RTS Request To Send (Input) 5 CTS Clear to Send (Output) 7 SG Signal Ground 8 DCD Data Carrier Detect (Output) 12 RTS Request To Send (Output) 20

  • ESTeem 192C, APPENDIX D SOFTWARE COMMANDS Revised: 13 Sep 05 APX D- 11 EST P/N AA104 S/N Serial Number command. When executed from the Command Model will output the ESTeem serial number of the unit that is defined at the time of manufacturer. SQDCTRL (on/off) This function enables the Square D controller protocol. For further detail Reference the EST Engineering Report on Square D controller interfacing. Factory default = OFF. SQDADD (1-254) This function is used with the SQDCTRL command to control the address fen

  • ESTeem 192C, APPENDIX A FCC INFORMATION Revised: 14 Apr 05 APX A-3 EST P/N AA104 FEDERAL COMMUNICATIONS COMMISSION FIELD OFFICES ALASKA 1011 E. Tudor Rd. Rm 240 Box 2955 Anchorage, AK 99510 CALIFORNIA 7840 El Cajon Blvd Suite 405 La Mesa, CA 92041 3711 Long Beach Blvd Suite 501 Long Beach, CA 90807 323A Battery St San Francisco, CA 94111 COLORADO Executive Tower 1405 Curtis St Suite 2925 Denver, CO 80202 FLORIDA 919 Federal Bldg 51 SE First Ave. Miami, FL 33130 1211 N. Westshore Suite 601 A.D. P. Building Tampa, FL 33607 GEORGIA Massell Bldg. 440 1365 Peachtree NE Atlanta, GA 30309 HAWAII 7304 Prince Kuhi Federal Building Honolulu, HI HAWAII 300 Almoana Blvd. P

  • ESTeem 192C, TABLE OF CONTENTS Revised: 13 Sep 2005 1-1 EST P/N AA104 CHAPTER 1 – STARTING OUT Before You Start 1-1 ESTeem Utility 1-1 Installing ESTeem Utility Software 1-1 Running the Program 1-2 Starting Out 1-2 Basic ESTeem Programming 1-4 Help Functions 1-4 Saving a Program 1-5 Restoring Factory Defaults 1-5 CHAPTER 2 – MODES OF OPERATION Command Mode 2-1 Converse Mode 2-1 Transparent Mode 2-2 Semi-Transparent Mode 2-3 Hardware Mode Control 2-3 CHAPTER 3 – PROGRAMMING ESTEEM FEATURES Digi-Repeater 3-1 Global Broadcast 3-2 Auto Transmit 3-2 Auto Connect

  • ESTeem 192C, CHAPTER 2 MODES OF OPERATION Revised: 15 Oct 03 2-2 EST P/N AA104 3. Termination control timer. The termination control timer is enabled by the TERMC (on/off) command. When enabled, the termination timer starts from the time the last transmit buffer has been updated in the RS-232C port. If the termination timer expires before another character is received or transmitted, the contents of the ESTeem transmit buffer will be transmitted. The waiting time of the timer is defined by the TERMT variable (termination time).

  • ESTeem 192C, APPENDIX D SOFTWARE COMMANDS Revised: 13 Sep 05 APX D- 10 EST P/N AA104 RXEnd (1-255) This command defines the time (milliseconds) to wait after the last character is received before reinitializing the receiver. Factory default = 1. RXSIGNAL (on/off) This command enables the signal to noise ratio meter output. Output level varies from 0 to 248 (248 being the highest reading). ON: Enabled. OFF: Disabled. Factory default = OFF. SAve The save command. The execution of this command stores the current command values and switches. Note: Please wait approximately two seconds after executing the SAVE command before turning off power to the ESTeem. SECURITY (off or 1- 100000) The security command

  • CHAPTER 1 STARTING OUT Revised: 15 Oct 03 1-3 EST P/N AA104 8. Press Set Serial Switches button. This window will configure the ESTeem’s RS-232/422/485 to operate at the setting selected in step 7 to match the computer port setting. Follow the on-line guide to configure the data rate. 9. Press Test ESTeem button. If the ESTeem serial interface cable and communication po

  • ESTeem 192C, APPENDIX B SPECIFICATIONS Model 192M/MHP Antenna Specifications Revised: 13 Apr 05 APX B- 9 EST P/N AA104 Model: AA202M Antenna Type: Directional, 3 Element Yagi, DC Ground Applications: Fixed base mounting. Frequency: 150 to 174 MHz Polarization: Vertical or Horizontal Impedance: 50 ohms Gain: 7.1 dB VSWR: < 1.5 Front To Back Ratio: 17 dB Horizontal Beamwidth:72 degrees Vertical Beamwidth: 57 degrees Antenna Material: 6061-T6 Aluminum Boom Diameter: 7/8 in. 6061-T6 Aluminum, double wall construction Mounting Hardware: Stainless steel U bolts for mounting to 1 5/8 in. diameter pipe. Antenna

  • ESTeem 192C, APPENDIX B SPECIFICATIONS Model 192C/CHP/F/M/MHP Overall Specifications Revised: 13 Apr 05 APX B- 2 EST P/N AA104 ESTeem Model 192C ESTeem Model 192CHP Frequency Range 450 to 470 MHz 450 to 470 MHz Frequency Selection Digitally Synthesized - Software Selectable Digitally Synthesized - Software Selectable Frequency Stability +/- 1 ppm +/- 2.5 ppm Frequency Selectability 6.25KHz 6.25KHz RF Data Rate 19,200 bps @ 25 KHz Channel Spacing U.S.A. Type Acceptance: ENPESTEEM192 Emission Designator: 17K6F1D 9,600 bps @ 12.5 KHz Channel Spacing U.S.A. Type Acceptance: ENPESTEE

  • ESTeem 192C, APPENDIX D SOFTWARE COMMANDS Revised: 13 Sep 05 APX D-1 EST P/N AA104 Listed below are the software commands and their factoy default setting. HELP CONTROL APPENDRU = 255 CONNECT CONVERS DISCONNE FACTORY FLASH HELP MULTID = OFF PACKMON = OFF RADIO = OFF RESET ROUTE = 0 RESTORE = 0 SAVE TRANSPAR = OFF HELP RS-232 AUTOLF = ON BLOCK = OFF COMRATE DTR_ENAB = OFF ECHO = ON MODECONT = OFF XHFLOW = OFF XSFLOW = ON HELP SETUP ADDRESS = 1 COMMAND = 3 EDIT = ON MESSFORM = OFF NETWORK = 37 PACKLENG = 2000 PROMPT = ON RETRY = 6 SENDPAC = 13 SETCON = 2 TERMCONT = OFF TERMTIME = 50 TYPERROR = OFF TYPSY

  • ESTeem 192C, CHAPTER 7 THEORY OF OPERATION Revised: 9 Oct 03 7-3 EST P/N AA104 EFFECTIVE BAUD RATE The maximum input baud rate to the modem is 19,200 baud, asynchronous, full duplex, but this is misleading since the ESTeems actually communicate to each simplex over the RF link, at 19,200 bps (25 kHz channel spacing - Model 192C/F) or 9,600 bps (12.5 kHz channel spacing - Model 192C/F). The effective baud rate is a function of the above plus the packet length variable in the ESTeem (definable from 1 to 2000 bytes). If the packlength variable is set to 2000 bytes the effective baud rate is approximate

  • ESTeem 192C, CHAPTER 3 PROGRAMMING ESTEEM FEATURES Revised: 15 Oct 03 3-5 EST P/N AA104 REMOTE PROGRAMMING The Remote Programming feature allows the user to remotely program ESTeems in his network. When a connection has been made with the remote ESTeem the RPG: prompt will be displayed showing that you are now in the COMMAND mode of that remote ESTeem. To enable this feature perform the following from the COMMAND MODE: PROG (1-254) Address of destination ESTeem. Note: You can also use the Repeater routing (r1,r2,r3,da) to reac

  • ESTeem 192C, APPENDIX B SPECIFICATIONS Model 192C/CHP/F Antenna Specifications Revised: 13 Apr 05 APX B- 7 EST P/N AA104 Model No: AA202C & AA202F Antenna Type: Directional, DC grounded, 5 element yagi. Applications: Fixed base. Frequency: 450 to 470 MHz - AA202C 400 to 420 MHz - AA202F Polarization: Vertical or Horizontal Impedance: 50 ohms Gain: 10 dB VSWR: < 1.5 Front To Back Ratio: 20 dB Horizontal Beamwidth: 59 degrees Vertical Beamwidth: 53 degrees Antenna Material: High strength aluminum with gold chromate finish. Mounting Hardware: Heavy du

  • CHAPTER 4 ESTEEM APPLICATION PROGRAMS Revised: 8 Oct 03 4-1 EST P/N AA104 Listed below are different application programs to aid the user in programming the ESTeem. TRANSPARENT AUTO-CONNECT This mode is used for a dedicated point to point application. The ESTeem will initiate the radio link when data is received by the RS-232/422/485 port. Perform the following prior to programming t

  • ESTeem 192C, CHAPTER 2 MODES OF OPERATION Revised: 15 Oct 03 2-3 EST P/N AA104 SEMI-TRANSPARENT MODE This mode should be utilized when sending a non-ASCII file and there is a possibility that the SENDPAC character could be contained in the transmitted data set. Perform the following prior to programming the ESTeem to initialize the unit to factory default settings: 1. Turn Bit 2, OFF on the RS-232C Setup Switch. 2. Reset the ESTeem. 3. TYPE FA <Enter>. Please note the characters may or may not be echoed by the CRT. ESTeem ------------------------- ADD xxx xxx = your address SETC yyy yyy = destination address TERMC ON TERMT 10 SE

  • ESTeem 192C, CHAPTER 3 PROGRAMMING ESTEEM FEATURES Revised: 15 Oct 03 3-4 EST P/N AA104 MULTI-CONNECT The actual polling of the ESTeem must originate from the host device connected to the ESTeem using the CONNECT command to originate the initial connect and the COMMAND character to return from the CONVERSE mode to the COMMAND mode. The first time around the pole a CONNECT data packet (RF transmission) will be initiated. When a link is established, it is held internally in the ESTeem connect table. The next time around the pole to the same address, the l

Related Products and Documents (Modem):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 FLIR PT-602CZ Installation manual flir/pt-602cz-UY7.pdf 26 Jan 2024 38
2 Sony RDR-VX525 - DVDr/ VCR Combo Quick setup manual sony/rdr-vx525-dvdr-vcr-combo-D1S.pdf 19 Sep 2022 2 3.14 Mb
3 Philips SPA7380 Operation & user’s manual philips/spa7380-13O.pdf 23 Apr 2023 2 1.91 Mb
4 Pro-Linear PL1007 Owner's manual pro-linear/pl1007-CD3.pdf 04 Mar 2023 7
5 Moffat Bakbar E35 Installation & operation manual moffat/bakbar-e35-C9H.pdf 03 Feb 2024 19
6 Stihl MS441 C-M Chainsaw stihl/ms441-c-m-N79.pdf 08 Mar 2024 128 3.95 Mb

Similar Resources:

  • Siemens

    Simatic ET 200S

    (14 pages)
    Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0) ___________________ ___________________ ___________________ SIMATIC ET 200S distributed I/O Digital electronic module 8DO DC24V/0.5 A (6ES7132-4BF00-0AA0) Manual 10/2015 A5E01077385-AB Preface Properties 1 Diagnostics 2 …
  • NETGEAR

    DM602 - ADSL-Modem - 8 Mbps DSL Modem

    (66 pages)
    SM-DM602October 2002NETGEAR, Inc.4500 Great America Parkway Santa Clara, CA 95054 USAPhone 1-888-NETGEARReference Manual for the Model DM602 ADSL Modem DM602.book Page i Friday, October 4, 2002 4:22 PM …
  • Paradyne

    3820Plus

    (5 pages)
    You have accessed an older version of aParadyne product document.Paradyne is no longer a subsidiary ofAT&T. Any reference to AT&T Paradyne isamended to read Paradyne Corporation. …
  • iWOW

    iTegno 3832

    (29 pages)
    iTegno 3832 GPRS Modem Hardware User Guide (For firmware version AB_02_00_30N_DEF003) Date : 11 April 2008 Document Version : 1.0 Our Reference : 02000C09 Confidential …
  • ActionTec

    GT724WG

    (16 pages)
    89028/2-10/61221-888-850-5915Technical SupportTable of ContentsGeneral Information ....................................... 1System Requirements ..................................... 2Step 1: Verify Computer Settings ................... 3Step 2: Router Installation .............................. 6Step 3: Configuring Your Router ..................... 7Step 4: …
  • Laipac

    M2M 3350

    (26 pages)
    M2M 3350 GSM/GPRS Modem User’s Manual & Reference Guide Revision 1 – June 2007 ©1999-2007 by Laipac Technology, Inc. All rights reserved – The Specifications and information regarding the products in this manual are subjected to change without notice. All statements, information, and recommendations in this manual are believe …

Comments, Questions and Opinions: