Manualios.com

Hornby 'Select' Unit Operator's Manual

Hornby 'Select' Unit Manual Online:

3.35, 947 votes
Hornby 'Select' Unit User Manual
Hornby 'Select' Unit User Guide
Hornby 'Select' Unit Online Manual

Text of Hornby 'Select' Unit User Guide:

  • Hornby 'Select' Unit, Digital Command Control Digital Command Control For more information visit: www.hornby.com Welcome to the digital Hornby World of model railways.You are about to enjoy a new and exciting experience when it comes to controlling and operating a model railway. Using the keypad that is on the Select unit locomotives can be “called up” individually and operated just like the real thing. Imagine a busy marshalling yard where the locomotives are positioned close together and where by using the Hornby Select Digital Controller, Hornby digital locomotives can be manoeuvred from one place to another without

  • Hornby 'Select' Unit, Keyboard The keyboard has 16 keys used to register and programme locomotives or accessories, set inertia or acceleration levels, direction settings, and for emergency stopping! The Select allows for 59 locomotives to be registered to the unit and 40 accessories. Each locomotive can be coded with up to 99 levels of acceleration or deceleration speeds. Locomotives have an ID number allocated to them from 1 - 59 and similarly accessories are given numbers of 60 - 99. Rotary Control Once the locomotive required to run has been “called up” and the direction of travel

  • Before any programming can commence ensure that all locomotives are removed from the track, apart from the one to be coded with an alternative number (eg. No.1). Should any point decoders be connected to the track ensure that they are also disconnected as well. All locomotives are coded as No. 3 at the factory.To change the code from No. 3 to No. 1 (for example) the following steps mu

  • Hornby 'Select' Unit, Deceleration Programming: 1. Ensure that the locomotive you wish to programme is the only one on the track. 2. Press and hold the Function button + for 1 second.The LCD display will flash “dE” (Deceleration). 3. Input deceleration time by pressing the appropriate numerical key(s).The lower the numbers entered the faster the deceleration. The higher the number (maximum 99) the slower. 4. Press “SELECT” to confirm.The LCD will flash the deceleration level once.The red LED will flash up to seven times during which the decoder will be accepting the command. If the LED flashes eight times, it is advisable to reprogra

  • Hornby 'Select' Unit, It is possible to have more than one locomotive running on the same track at the same time with the Hornby Select Digital Control unit.As an example it is assumed that there are three locomotives coded 1, 2, 3. Operating Multiple Locomotives: Step 1. Press on the keypad and then “SELECT”.Turn the Control Knob and locomotive No. 1 will begin to move. Step 2. Press on the keypad and then “SELECT”.Turn the Control Knob and locomotive No. 2 will begin to move. Locomotive No. 1 will continue to run but will not respond to the controll

  • Hornby 'Select' Unit, The Select control units feature two methods of “calling up” locomotives that are stored in the units memory. The keypad can be used to enter locomotive addresses directly, or the Select button can be pressed to cycle through the list of stored addresses. Method 1: To select a locomotive address directly using the keypad. 1. Enter the locomotive address on the keypad. 2. Press “SELECT“ to confirm. The LCD Display will show the new locomotive address. Method 2: To cycle through the locomotive address stored in the control unit’s mem

  • Hornby 'Select' Unit, The Hornby Select Digital Control is capable of controlling 2 locomotives at the same time as if they are one entity. Creating a Consist: (Double Heading) 1. Place the locomotives you wish to Consist on the track.These should be programmed with individual addresses and set to the same direction. 2. Enter the address (between 0 and 59) you wish to use for the Consist, and press “SELECT”. Ensure that the address used is different from the two locomotives you wish to Consist. The LCD displays the chosen address. 3. Press and hold “FUNCTION” for 1 second.The LCD display will flash “A1”. 4. Using the keypad, enter the address of the first locomotive you wish to add to th

  • It is possible but not recommended that a locomotive that is not fitted with a decoder (analogue) can be operated on a digital layout.This locomotive is given the address “0”. Running an Analogue Locomotive: 1. Press on the keypad. Press “SELECT” to confirm. The LCD will display 00. 2.Turn the Control Knob clockwise to move the locomotive. Pressing the or bu

  • Hornby 'Select' Unit, For more information visit: www.hornby.com The Hornby Select Digital Control unit can have stored in its memory 59 digitally controlled locomotives. At any one time the Select can have running (providing the power is available) or on standby 10 locomotives. This is more than sufficient for an above average layout, however should an eleventh loco be “called up”, one of the previous 10 locomotives will be returned to the memory.The locomotive that is returned, will be the locomotive that has the lowest current Speed address compared to the other 9. Alternatively, if all 10 locomotives ar

  • Hornby 'Select' Unit, For more information visit: www.hornby.com 20 Walkabout Mode The Hornby Select unit is capable of having connected to it up to 7 Select Walkabout units.The addition of these units to the Select will provide independent control of up to 8 locomotives providing electrical power is available. It is also possible that a locomotive can be passed from one controller to the next and then the next in much the same way as a full size steam train is handled on the main line. Connecting the Walkabout 1. Locate the XpressNet port situated at the rear of the Select Command Station unit and insert an RJ12 6 pin buddy cable. LCD will display “03”. 2. L

  • Hornby 'Select' Unit, For more information visit: www.hornby.com 22 Programming Track When addressing locomotives and Hornby Point/Accessory Decoders it is important that all other locomotives are removed from the track. It is also important that all point decoders are disconnected from the layout. This can become rather difficult at times, therefore it is suggested that a Programming Track is used for the allocation of addresses.A Programming Track is a length of track electrically isolated from the main circuit but includes one Hornby R8206 Power Track and an R046 lever switch.To initiate the Programming Track, (see diagram below) use the Lever switch t

  • Hornby 'Select' Unit, Hornby Digital Points Decoder The Hornby Select Digital Control is capable of operating up to 40 points or solenoid operated accessories when used in conjunction with the Hornby R8216 Points Decoder Module. The Point Decoder Module can operate up to 4 points or solenoid operated accessories. Fitting the Hornby Point/Accessory Decoder: 1. Connect the wires from the point accessory motor to the first available input terminals on the decoder.Then connect the wires from the point decoder to the track or Programming Track (see page 22). Full wiring instructions are supplied with each Module. Addressing Points/Accessories: Address

  • Hornby 'Select' Unit, For more information visit: www.hornby.com Glossary 26 27 Acceleration Delay The delay between the locomotive being stationary and reaching the desired speed. Accessory Decoder An electronic decoder designed for use in track side accessories such as points or signals.An accessory decoder is not for use in a locomotive. Address A number used to identify a locomotive or accessory that is either equipped or linked to a Decoder. Bus Technical term for wires that carry electrical signals around a model

  • Hornby 'Select' Unit, Glossary (Continued) For more information visit: www.hornby.com 28 29 Speed Steps A variable voltage increase used to control motor speeds. Decoders can set the output power for each speed step. Stall Current Stall Current is the maximum current draw in amperes that a locomotive is capable of when stalled. If the armature of a motor is prevented from turning and the maximum voltage is applied the current draw of the motor is known as the ‘Stall Current’. Throttle Notches Determines whether a locomotive is controlled with 14, 27, 28 or 128 speed steps. XpressNet A h

  • Hornby 'Select' Unit, 31 Notes Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. For more information visit: www.hornby.com 30 Locomotive Address Safety Notes ● This product is intended for indoor use only. ● This Select Digital Control system is only to be operated with the Hornby recommended transformers. ● The transformer included is not a toy; it is a “Transformer for Toys”. �

Related Products and Documents (Toy):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Makita 4101RH Technical information makita/4101rh-62P.pdf 25 Nov 2023 4
2 Electrolux Air-O-Speed 593800300 Service manual electrolux/air-o-speed-593800300-41F.pdf 27 Dec 2022 20 2.27 Mb
3 Schulz SM 7-80 Manual  schulz/sm-7-80-17P.pdf 24 Sep 2023 19
4 Fisher-Price V3394 Quick start manual fisher-price/v3394-6DD.pdf 17 Oct 2023 24 2.28 Mb
5 Whirlpool WHED20 Installation and operation manual whirlpool/whed20-5QG.pdf 07 Nov 2023 11 0.63 Mb
6 Pharos PA-1200 Operation & user’s manual pharos/pa-1200-6WE.pdf 15 Jul 2022 8 1.58 Mb

Similar Resources:

  • Heli-scale

    Bell HUEY 412

    (15 pages)
    HELI - SCALE Copyright ® 2012 - Reproductions interdites www.heli-scale.fr Manuel d’assemblage Instruction manual Bell HUEY 412 Part 2 Cher client, Merci d’avoir choisi un fuselage/accessoire HELI - SCALE. Toute l’équipe vous souhaite une bonne construction et de bons vols. Dear customer Thank you for choosing a scale fuselage/accessories H …
  • Black Horce Model

    L-13 BLANIK BH135

    (22 pages)
    Instruction Manual bookSPECIFICATIONMade in Vietnam. Wingspan : 4,200mm. 163.35 in. Length : 2,100 mm. 82.68 in. Weight : 7,6 kg. 16.72lbs Radio : 07 channels. Servo : 05 – 06 standard high torque servos, size (40 x 20 x 38)mm …
  • Mega Bloks

    Barbie

    (28 pages)
    Build ‘n Play Walk-In Closet | Salle-penderie Construis et joue | Vestidor para construir Armário de Construir e Jogar | Cabina Armadio da costruire | Begehbarer Kleiderschrank zum Bauen und Spielen Buduj i baw się - Garderoba | Bouw en speel inloopkast | Игровой набор “Гардеробная” …
  • MTHTrains

    30-2519-0

    (16 pages)
    RAILKING E-33 RECTIFIERELECTRIC ENGINEOPERATING INSTRUCTIONSThis RailKing E-33 Rectifier Engine comes with an ABS body and die-cast fuel tank &trucks, and runs on O-31track. This RailKing Electric Engine contains M.T.H.’sLoco-Sound™ sound and train control system. The locomotive is easy to operate withany compatible standard AC transformer (see the …
  • Uncle Milton

    Star Wars Science Jedi Telescope

    (1 pages)
    Using your Jedi™ TelescopeTelescope Mode1. Turn the image dial until you no longer see an image and are looking through the telescope. 2. Slide the fast-focus grip to quickly put the image into focus. Then turn the fine focus dial to put the image in sharper focus.Space Image Mode Turn the image dial while looking through your telescope. As you rotate …
  • Sebart

    Mini Avanti

    (3 pages)
    SebArt professional line Mini Avanti 1.4m ARF Jet for EDF or P20 micro-turbine Instruction Manual The all new Mini Avanti Jet 1.4m ARF was designed by Italian champion aerobatic pilot Sebastiano Silvestri. This sport ARF jet-model design is based on the Hawk full size aircraft design and modified by adding the ultimate aerodynamic ideas of modern pattern …

Comments, Questions and Opinions: