taiyo TF-711 Operation & User’s Manual
|
taiyo TF-711, - 17 - 3.4.3 Sleep timer setting The sleep timer indicates the sleep mode after a specified time for reception has passed and its setting is made as following. Press key. Then the message is shown on the right. The displayed numbers refer to the following operations. 1 : Release 2 : Setting (1) Release Select “1” in the above message, and fix with key. (display on the right) Note: When the system is in the sleep mode, press & keys to shift the mode to the standard operation mode. (2) Setting Select “2” in the above message, and enter
taiyo TF-711, 1 2 DC power supply unit FUSE DC10 40V 5A Power supply unit is interchangeable Grounding wire TF-711 main unit 1 3 2 AC V 2A FUSE BK IN EXT IN A F 1 2 OUT IN BK External receiver DECODER A F IN A F OUT A F OUT TFM-01 A ntenna coupler Option 2m whip antenna M207-P(7C-2V) M205-P(5C-2V) 7C-2V or 5C-2V M205-P M207-P CAUTION 1. Turn ON the switch S1 on the PCA BK inside the TF-711 main unit when the antenna coupler TFM-01 is used. 2. Turn ON the switch S2 on the PCA BK when a decoder is connected. Layout
taiyo TF-711, - 22 - 3.6 Connection of a decoder The terminal board (AF OUT/IN) is provided so that a decoder of secrecy broadcasts, such as Kyodo News (JJC), can be used. Turn ON the DIP-switch S2 (marked “DEC”) on BK board (inside the unit, attached to the terminal board) . Turn the power switch OFF and ON again after connection and S2 switch-ON. The channel as which “D” is indicated on the lower right of the display shows that the signal comes through a decoder. Even if “D” is not displayed, select "DECORDER-ON" at registration of new frequency with reference to 1.4.4 to receive a signal t
taiyo TF-711, - 10 - Channel key : For selection of channel mode from frequency mode, and for shift to the channel setting in the channel mode. For setting a channel, press key and enter channel number with three keys. The channel covers 000 443 (existent frequency) and 450 724 (new frequency). Clear key : For deletion of memorized value in a set mode and for return to the standard operation mode from a set mode. Record key : To start and stop recording. In the non-recording mode, a press of key sets automatic phasing mode and recording starts when phasing is completed. In the automatic phasing, a press of key stops the a
- 11 - 3.2 Contrast and brightness Contrast of LCD display depends on the visual angle and the temperature and hence, be sure to adjust it with the contrast knob (see Fig. 1) for optimum result at the time of installation. The backlight brightness of the LDC can be adjusted in four stages by pressing the key. 3.3 Basic operation Power switch is on the le
taiyo TF-711, - 2 - 2. INSTALLATION 2.1 Main unit Install the TF-711 main unit on a plane desk or a solid and plane wall with 4 pcs. of screws and washers. Caution: A print may become blurred if the installation place is uneven. In that case, put some washers or suitable attachment to adjust the flatness as following figure. Setscrew for cabinet Setscrew For cabinet Washer TF-711 main unit
taiyo TF-711, - 16 - (3) Re-calling (readout of the booking data) Press key. Select a booking number to be confirmed by pressing key. Then, contents of the booking data is displayed. (4) Entry booking Press key. Select a timer number for booking by pressing key. Then, the unit will ask whether the number is correct or not. Fix the number by pressing the key or enter a new number if the number is not correct. The display on the right shows when the number 1 is set. Then, enter a channel number with three keys (or press two keys and key for automatic setting of the
taiyo TF-711, - 8 - 3. OPERATION The unit, with antenna(s) and power supply, receives and records signal automatically by the control of APSS when desired channels have been set. 3.1 Description of key Program key : For preparation to mode setting. One of following modes can be selected by pressing key and next, a key. Be sure to follow instruction of the indicator in selecting a mode. To cancel a setting, press the key to reset to the initial display of selection mode. Then, press a key to reset or the key to set the standard operation mode. PRG PRG C N 0 9 N 0 9 1 1
taiyo TF-711, FOR SERVICE REQUIREMENT For any inquiry of service, please contact to a dealer where you purchased this equipment. When the dealer's contact address is uncertain, please contact to following address. 2-11-18, Higashi-Kojiya, Ota-ku, Tokyo 144-0033 JAPAN Overseas Trading Dept. TEL: 81-3-5735-1247 FAX: 81-3-5735-1683
taiyo TF-711, TF-711 FACSIMILE STATION TABLE CHANNEL NO. CALL SIGN STATION FREQUENCY [kHz] 000 JMH JAPAN 3622.5 001 JMH JAPAN 7305.0 002 JMH JAPAN 9970.0 003 JMH JAPAN 13597.0 004 JMH JAPAN 18220.0 005 JMH JAPAN 23522.9 010 JMJ JAPAN 3365.0 011 JMJ JAPAN 5405.0 012 JMJ JAPAN 9438.0 013 JMJ JAPAN 14692.5 014 JMJ JAPAN 18441.2 020 JJC JAPAN 4316.0 021 JJC JAPAN 8467.5 022 JJC JAPAN 12745.5 023 JJC JAPAN 16971.0 024 JJC JAPAN 17069.6 025 JJC JAPAN 22542.0 026 9VF JAPAN 16035.0 027 9VF JAPAN 17430.0 030 JFC JAPAN 4274.0 031 JFC JAPAN 6414.5 032 JFC JAPAN 8658.0 033 JFC JAPAN 13074.0
taiyo TF-711, - 5 - 2.5 Receiving antenna Following antennas are suitable to use as the receiving antenna for the TF-711. A) Antenna coupler TFM-01 + 2 m whip antenna (supplied by us as option) B) Whip antenna (6 m ~ 8 m) C) Wire antenna (Reverse-L or T type) Note: Generally, whip antenna is suitable for reception over 6 MHz, and wire antenna is suitable for reception under 6 MHz. Receiving sensitivity would become worse when using one antenna for other receivers and/or transmitters through multi-coupler. In that case, please use other antenna or install exclusive antenna. Be sure to connect BK especially for following case in orde
- 19 - ISB +0.0KHz OFF 1-OFF 2-ON 3-QTY ISB +1.9kHz ON PUSH ENT KEY SET ISB in 2FIG / by KEY 3.4.6 Setting of ISB frequency Signals from multiplex-communication station are easily received by setting an ISB (Independent side band) width as shown in the following. Pressing key sets the ISB setting mode and the message on the right is shown. The displayed numbers correspond to
taiyo TF-711, CHANNEL NO. CALL SIGN STATION FREQUENCY [kHz] 370 DDH HAMBURG 3855.0 371 DDK HAMBURG 7880.0 372 DDK HAMBURG 13882.5 380 OXT COPENHAGEN 5850.0 381 OXT COPENHAGEN 9360.0 382 OXT COPENHAGEN 13855.0 383 OXT COPENHAGEN 17510.0 390 VFF IQALUIT& RESOLUTE 3251.5 391 VFF 7708.1 400 CBV VALPARAISO 4228.0 401 CBV VALPARAISO 8677.0 402 CBV VALPARAISO 17146.4 410 NMC SAN FRANCISCO 4346.0 411 NMC SAN FRANCISCO 8682.0 412 NMC SAN FRANCISCO 12730.0 413 NMC SAN FRANCISCO 17151.2 414 NMC SAN FRANCISCO 22527.0 420 CKN VANCOUVER 2754.5 421 CKN VANCOUVER 4268.0 422 CKN VANCOUVER 6456.0 423 CKN VANCOUVER 12753.0
taiyo TF-711, - 23 - 4. Maintenance 4.1 Back-up battery This device uses a manganese lithium battery as a back-up battery. Please exchange to new one after using for 1~2 years. This battery is located on the CPU PCA. Please be careful about polarity when exchanging it. 4.2 Lubrication and Cleaning (1) Lubrication Lubricate a paper sending gear with 1-2 drops of lubricating oil at every 2-3 months. (2) Cleaning Clean the thermal head with attached cotton cleaner at every month. When garba
taiyo TF-711, - 24 - TABLE OF FACSIMILE STATION Table of pre-programmed frequencies and area map This unit has a ROM (read only memory) which is pre-programmed 443 existing frequencies of facsimile transmitting stations. Stations and frequencies are shown in the map and table respectively. This table is reference data and is subject to change without previous notice. JMH JMJ JJC JFC HLL BAF BDF BMF NPN ZKLF A XI HSW 5YE 6VU PWZ NMF CFH A OK DDK SUU Y MA GYA
taiyo TF-711, Personal injury or death may be resulted when handled improperly. A ll wiring should be properly insulated to prevent electric shock, especially when using AC power supply of 200V or higher. Protect wire and cables with pipes from heat or mechanical injury. The ground terminal on its rear panel should be connected to the vessel with copper belt or heavy braided wire. Handle LCD (liquid crystal display) carefully not to break its glass. When the glass is broken, do not touch the liquid in it. Particularly keep
taiyo TF-711, - 12 - 3.3.3 Start and stop of recording (1) Start Recording starts automatically (Start/Stop, Phase, Speed, IOC) by receiving the APSS signal. To start halfway of the received picture, press key once and automatic speed setting and auto-phasing mode are set. Then, recording starts upon phasing is completed. When the phase signal for automatic start is not received, recording does not start. Then, press key again for manual recording. (2) Stop Recording stops automatically when auto stop signal is received. In t
- 6 - 2.6 Exchange of a recording paper (1) Remove the front cover, up the paper cutting plate, slide the paper feed lever in the direction of rear. (Ref. Fig.1) (2) Set the roll paper to the holder by pressing a paper guide to left side. (Ref. Fig.2) Note: A paper detection sensor is at
taiyo TF-711, - 7 - ( 6) Install the front cover. A t that time, place the end of paper above the front cover. (Ref. Fig.6) (5) Return the paper cutting plate to the original position. (4) Pull down ahead the paper feed lever, pulling the end of paper a little ahead. (Ref. Fig.4)
CHANNEL NO. CALL SIGN STATION FREQUENCY [kHz] 090 ZKLF AUCKLAND 5807.0 091 ZKLF AUCKLAND 9459.0 092 ZKLF AUCKLAND 13550.5 093 ZKLF AUCKLAND 16340.1 100 AXM MELBOURNE 2628.0 101 AXM MELBOURNE 5100.0 102 AXM MELBOURNE 11030.0 103 AXM MELBOURNE 13920.0 104 AXM MELBOURNE 20469.0 110 AXI DARWIN 5755.0 111 AXI DARWIN 7535.0 112 AXI DARWIN 10555.0 113 AXI DARW
taiyo TF-711, 3.3.1 Channel setting 3.3.2 Fine-adjustment of frequency, and selection of a desired frequency 3.3.3 Start and stop of recording 3.3.4 3.3.5 3.3.6 3.3.7 Timer release and release of keylock in the timer mode 3.4.1 Switching of receiver (audio) 3.4.2 3.4.3 3.4.4 3.4.5 Time setting 3.4.6 3.4.7 3.4.8
taiyo TF-711, - 15 - 3.4.1 Switching of receiver (audio) Switching of the internal or external receiver is set by the following procedure. Press key. Then the receiver switching mode is set and message on the right appears. The displayed number 1 is for internal receiver, 2 is for external receiver. Pressing the key after setting a key, completes the setting. 3.4.2 Setting of timer reception This unit has 16 booking functions and each timer is set as follows. Press key. Then the timer reception setting mode is set and the message is shown on t
taiyo TF-711, - 9 - Dimmer key : For adjusting a backlight brightness of the LCD indicator, 4 levels selectable. Speed key : For selection of SPD (speed). IOC key : For selection of IOC. Up key : Channel up in the channel mode or frequency up in the frequency mode. Left key : For manual phasing in recording (towards left). A press of the key shifts 2.5% of the paper width. Right key : For manual phasing in recording (towards right). A press of the key shifts 2.5% of the paper width. Down key : Channel down in
taiyo TF-711, - 4 - 2.3 Terminal board Use terminal board on the rear panel of the main unit for the connection between BK, external receiver or decoder. Insert a connection wire in a terminal in the following ways. Note: Use connection wire with single core 0.4~1.0mmØ or standard twist core 0.3mm 2 ~0.7mm 2 . 2.4 Grounding A GND terminal is on the rear panel of the main unit. Be sure to ground the main unit using attached earth wire (3m KIV wire 50/0.45 with co
taiyo TF-711, - 18 - SET REVERSE SET DECODER SET IOC 576/288 SET SPEED 120-60 12:00 SET MIN. in 2FIG SET HOUR in 2FIG APR 10 MON ‘ SET YEAR in 2FIG A PR 10 SET DAY Of THE WEEK by A PR SET DATE in 2FIG SET MONTH by KEY Available frequency for setting are within 80.0 159.9kHz or 2000.0 24999.9kHz. Press key to fix the registration. To correct the entry halfway, use key for resetting. Further, the speed, IOC, reverse and decoder can be set in sequence. 3.4.5 Time setting Clock time can be set by the following procedure. Pressing the key sets the time setting mode and message shown on the right appears. Set month w
taiyo TF-711, CHANNEL NO. CALL SIGN STATION FREQUENCY [kHz] 230 CFH HALIFAX 4271.0 231 CFH HALIFAX 6496.4 232 CFH HALIFAX 10536.0 233 CFH HALIFAX 13510.0 234 CFH HALIFAX 122.5 240 AOK ROTA 7595.0 241 AOK ROTA 9050.0 242 AOK ROTA 10542.0 250 IMB ROMA 4777.5 251 IMB ROMA 8146.6 252 IMB ROMA 13587.4 260 LZJ SOFIA 5093.0 270 SWA ATHENS 4481.0 271 SWA ATHENS 6790.0 280 SUU CAIRO 4526.0 281 SUU CAIRO 10123.0 290 YMA ANKARA 3377.4 291 YMA ANKARA 6790.0 300 ROO ROSTOV N
- 1 - 1. SPECIFICATIONS 1.1 Receiver Reception : Synthesized double superheterodyne Frequency range : LF 80.0 ~ 159.9 kHz MF/HF 2.0000 ~ 24.99999 MHz Mode : F3C Selectivity : 3.0 kHz at –6 dB Number of channels : 396 channels Sensitivity : LF 10µV at 20 dB SINAD MF/HF 2µV at 20 dB SINAD Channel selection : Autom
Kyocera FS FS-3900DN Fax Machine Operation manual
FS FS-3900DN |
HP 3100C Fax Machine Administrator's manual
3100C |
Ricoh FAX1400L Fax Machine Operating instructions manual
FAX1400L |
Xerox 665 Fax Machine Operation & user’s manual
665 |
Muratec M-2500 Fax Machine Operating instructions manual
M-2500 |
Toshiba e-studio 353 Fax Machine Operation & user’s manual
e-studio 353 |
Cisco Aironet 1600 Series Fax Machine Deployment manual
Aironet 1600 Series |
Canon PIXMA MX922 Fax Machine Setup manual
PIXMA MX922 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Waeco | CoolFreeze CF | Instruction manual | waeco/coolfreeze-cf-5JK.pdf | 03 Oct 2023 | 64 | |
2 | VTech | 80-102200 - Crystal Sounds DECT Digital Monitor | Operation & user’s manual | vtech/80-102200-crystal-sounds-dect-digital-monitor-LK8.pdf | 12 Oct 2023 | 28 | 0.45 Mb |
3 | Xante | IMPRESSIA | Quick installation manual | xante/impressia-399.pdf | 29 Jun 2023 | 3 | |
4 | Pioneer | XW-HTP550 | Service manual | pioneer/xw-htp550-1K6.pdf | 21 Jan 2023 | 45 | |
5 | AT&T | CL4940 | Quick start manual | at-t/cl4940-O1P.pdf | 06 Jan 2023 | 2 | |
6 | NETGEAR | FS526T - Switch | Operation & user’s manual | netgear/fs526t-switch-HK3.pdf | 30 Mar 2024 | 50 |
Ricoh
Read this manual carefully before you use this product and keep it handyfor future reference.For safety, please follow the instructions in this manual.COPY REFERENCE340/350/450OPERATING INSTRUCTIONSND0A0101
…
Aficio 340(209 pages) |
Kyocera
FTP TransmissionThe FTP transmission converts the data of originals scanned on this machine to the PDF or TIFF format and uploads it directly to an FTP server.As upload destinations, up to 10 FTP servers can be registered. Uploading data to the 10 FTP servers simultaneously is available.In environment where an FTP server is operating, additional software ins …
KM-6030(2 pages) |
Kyocera
OPERATION GUIDEPlease read this Operation Guide before using this machine. Keep it close to the machine for easy reference.250ci/300ci/400ci/500ciDownloaded From ManualsPrinter.com Manuals
…
TASKalfa 250ci(488 pages) |
Konica Minolta
E-1INSTALLATION MANUAL/A0P0-9951-01<Important>Be sure to correctly follow the procedures in order as explained in this Installation Manual.If you do not follow the procedure in order, the image trouble may occur.I. Outline of installation proceduresWhen installing the machine and associated options as a system, follow the order shown on the upper.Note: …
BIZHUB C652(24 pages) |
Muratec
XXXX-XXXX-XXUser ManualPrinted in ChinaPlain-paper digital Fax/Copier/Printer/Scannerwww.muratec.comMuratec America, Inc.3301 E, Plano Parkway, Suite 100Plano, Texas 75074DA7-90010-60MML item number:OMF300MAI order number:Muratec America, Inc. 2004B5: 182 x 257 mm0 3 1 9 8 1 9 2 5 9 7 6
…
F-300(191 pages) |
Xerox
DFC155 & DWC155c Service Manual & Spare Parts Catalogue602E52970Important NoteThis is a first edition of the Service Manual and Spare Parts Catalogue.To read the manual Adobe Acrobat 3.0 is needed as the .pdf files are not 2.1 compatible.In the contents section there is a reference to remote diagnostics in chapter 5.The section on this has been remov …
DFC155(151 pages) |
Sylvania Speakers SP355Guide: Sylvania SP355 (4ERQVD, Upd.Tuesday 24-10-2023) SP355, 27 |
Nokia Cell Phone COMMUNICATOR 9110Nokia COMMUNICATOR 9110 User Guide (Operation & user’s manual), @BOLV8C COMMUNICATOR 9110, 190 |
Akai Musical Instrument MPCXManual: Akai MPCX (5GYL25, Upd.Mon 02.2024) MPCX, 12 |
AEG Oven EE1000001Operation & user’s manual for AEG EE1000001 Oven EE1000001, 24 |
MSI Video Card NX6800GT-TD256ENX6800GT-TD256E Quick installation manual - 8S79JW NX6800GT-TD256E, 2 |
Compaq Desktop DL360 - ProLiant - PhotonDesktop PDF Firmware update DL360 - ProLiant - Photon, 9 |
BBQ Grill GSF2616ACBBQ GSF2616AC User Manual (Owner's manual), @GE4XJZ GSF2616AC, 19 |
Samsung CD Player Z-10MMCD Player #99LHK7 Z-10MM, 24 |
AMX Touch Panel Modero NXD-700ViTouch Panel PDF Operation/reference manual Modero NXD-700Vi, 234 |
Craftsman Lawn Mower 917.377422#6Z5K84 917.377422: Craftsman Lawn Mower Owner Documentation 917.377422, 28 |
Nokia Cell Phone NAVIGATOR 6210#T77B2G NAVIGATOR 6210: Nokia Cell Phone Owner Documentation NAVIGATOR 6210, 7 |
Develop Printer ineo 3300PDevelop ineo 3300P User Guide (Doc Type: Printer Operation & user’s manual) ineo 3300P, 242 |