Manualios.com

Compartible Systems Corporation RISC 2600i Installation Manual

Compartible Systems Corporation RISC 2600i Manual Online:

3.4, 1005 votes
Compartible Systems Corporation RISC 2600i User Manual
Compartible Systems Corporation RISC 2600i User Guide
Compartible Systems Corporation RISC 2600i Online Manual

Text of Compartible Systems Corporation RISC 2600i User Guide:

  • Compartible Systems Corporation RISC 2600i, Appendix B - Connector and Cable Pin Outs 33 Appendix B - Connector and Cable Pin Outs Pin Outs for DB-26 to V.35 Male Cable DB-26 V.35 Signal 25 A < - > Chassis Ground 26 B < - > Signal Ground 19 C - > Request to Send 20 D < - Clear to Send 21 E < - Data Set Ready 23 F < - Receive Line Signal Detect 22 H - > Data Terminal Ready 1 P - > Tx Data 4 R < - Rx Data 10 S - > Tx Data 13 T < - Rx Data 6 U - > Tx Clock Out 15 W - > Tx Clock Out

  • Compartible Systems Corporation RISC 2600i, v Suggested for IP 24 IPX Protocol 25 Required for IPX 25 Suggested for IPX 25 PPP Link Configuration 25 Required for Dedicated/Leased Line Operation 25 Suggested for Dedicated/Leased Line Operation 26 Required for Dial-On-Demand Operation 26 Suggested for Dial-On-Demand Operation 26 WAN I NTERFACE FRAME RELAY CONFIGURATION 27 IP Protocol 27 Required for IP 27 Suggested for IP 27 IPX Protocol 28 Required for IPX 28 Suggested for IPX 28 Frame Relay DLCI Mappings 28 IP Protocol 28 Required for IP Numbered Interface 29 Required for IP Unnumb

  • Compartible Systems Corporation RISC 2600i, 8 Chapter 1 - Introduction BE SURE THAT YOUR ROUTER CONFIGURATION IS ALLOWING THE ROUTER TO DROP THE COMMUNICATIONS LINK WHEN IT ISN’T NEEDED. RISC Router 2600i Installation Overview This manual will help you install the RISC Router 2600i to connect a local Ethernet to up to 4 remote networks and/or remote PPP client computers. These connections can be made to other Compatible Systems routers, routers from other vendors, or PPP compliant dial-in software packages running on a variety of computers. The wide-area interfaces on the RISC Router 2600i may be used to interconnect your network with other co

  • 40 Appendix E - Terms and Conditions damaged by causes external to the Products, including (without limita- tion) shipping damage, power or air conditioning failure, or accident or catastrophe of any nature; and (d) have been subjected to repairs or attempted repairs by any person other than Compatible Systems (or an authorized Compatible Systems service technician). To obtain service

  • Compartible Systems Corporation RISC 2600i, vi IP Defaults 32 IPX Defaults 32 V.35 (WAN 0) Link & Physical Defaults 32 Appendix B - Connector and Cable Pin Outs 33 Pin Outs for DB-26 to V.35 Male Cable 33 Pin Outs for DIN-8 to RS-232 Console Cable (DTE/Female) 34 Appendix C - LED Patterns and Test Switch Settings 36 RISC Router 2600i LED Patterns 36 Power On, No Traffic 36 Ethernet Traffic Indicators (Ethernet LED Bar) 36 Other Indicators (on All LED Bars) 36 Panic Indicators 36 RISC Router 2600i Switch Settings 37 Appendix D - Downloading Software From Compatible Systems 38 Appendix E - Terms and Conditions 39

  • Compartible Systems Corporation RISC 2600i, RISC Router 2600i Installation Guide, Version 2.0 Copyright(c) 1997, Compatible Systems Corporation All rights reserved. MicroRouter, RISC Router, and RouterView are trademarks of Compatible Systems Corpo- ration. Other trademarks are the property of their respective holders. Part number: A00-1346 FCC Notice: This product has been certified to comply with the limits for a Class A computing device, pursuant to Subpart J of Part 15 of FCC Rules. It is designed to provide reasonable protection against radio or television communi- cation interference in a commercial environment. Oper

  • Chapter 6 - Basic Configuration Guide 29 face as a “numbered interface.” This means that the interface (and thus the Frame Relay network) will have an IP address, subnet mask, etc. The other is to set it as an unnumbered interface and specify that the link is point-to-point Frame Relay and set the local DLCI. Required for IP Numbered Interface • IP nu

  • Compartible Systems Corporation RISC 2600i, Appendix E - Terms and Conditions 39 Appendix E - Terms and Conditions Compatible Systems Corporation (Compatible Systems) offers to sell only on the condition that Customer’s acceptance is expressly limited to Compatible Systems’ terms and conditions of sale. Compatible Systems’ acceptance of any order from Customer is expressly made conditional on assent to these terms and conditions of sale unless other- wise specifically agreed to in writing by Compatible Systems. In the absence of such agreement, commencement of performance or

  • Compartible Systems Corporation RISC 2600i, 20 Chapter 5 - Command Line Management 1. Set the host’s IP address to 198.41.12.2, with a Class C subnet mask (255.255.255.0) and then Telnet to 198.41.12.1. 2. Enter the default password letmein at the password prompt. The command line interface prompt will appear on the screen. 3. Use the configure command and set the IPAddress, SubnetMask, and IPBroadcast keywords in the IP Ethernet 0 section. 4. Use the save command to save the changes to the device’s Flash ROM. 5. Change the host’s configuration back to its original settings See the next section (Setting Up Telnet Operation) for information

  • 38 Appendix D - Downloading Software From Compatible Systems Appendix D - Downloading Software From Compatible Systems We make the latest versions of operating software for all Compatible Systems products available at our Web site. The latest version of CompatiView management software is also available. To download software, follow the instructions below.

  • Compartible Systems Corporation RISC 2600i, iii Chapter 1 - Introduction 7 ABOUT THE RISC ROUTER 2600I 7 A NOTE ABOUT FIREWALLS 7 A NOTE ABOUT ON-DEMAND INTERNETWORKING 7 RISC ROUTER 2600I INSTALLATION OVERVIEW 8 Chapter 2 - Getting Started 8 Chapter 3 - Network Installation 9 Chapter 4 - CompatiView Software Installation 9 Chapter 5 - Command Line Preparation 9 Chapter 6 - Basic Configuration Guide 9 Appendices 9 Chapter 2 - Getting Started 10 A FEW NOTES 10 Please Read The Manuals 10 Getting Help With the RISC Router 2600i 10 WHAT YOU WILL NEED TO GET STARTED 11 Supplied with the RISC Router 2600i 11 Needed For Installation 11 Ethernet Connection Requirements 11 10Base-T Twisted-Pair Ethernet 11 Telco Line Conn

  • Compartible Systems Corporation RISC 2600i, Chapter 3 - Network Installation 13 Chapter 3 - Network Installation RISC Router 2600i Back Panel This section of the manual describes how to connect the RISC Router 2600i to your Ethernet network and your wide area communications device(s). In summary, the steps for installation are: 1. Make sure the router is powered down and unplugged from the wall. 2. Connect the router to the Ethernet network. 3. Connect the router to the wide area line communications device(s). 4. Power up the line communications devices.  Note: You should either wait to connect a synchronous line devi

  • Compartible Systems Corporation RISC 2600i, 30 Chapter 6 - Basic Configuration Guide section. Add static routes and a default router using the edit config IP Static command. IPX Protocol Required for IPX Frame Relay operation requires that the WAN interface is set to be a “numbered interface.” This means that the interface (and thus the Frame Relay network) must have an IPX network number. • IPX numbered interface • IPX Network Number CV: Use the IPX Routing: WAN 0 (and/or other ports) Dialog Box. TB:Use configure and set the Numbered and Net keywords in the IPX WAN 0 (and/or other ports) section. Suggested for IPX The settings above

  • Compartible Systems Corporation RISC 2600i, 10 Chapter 2 - Getting Started Chapter 2 - Getting Started A Few Notes Please Read The Manuals The manuals included with your RISC Router 2600i contain some very important information about the RISC Router 2600i and local and wide area networking in general. Please read this manual thoroughly, and refer to the management reference guides as required. It’s worth the few minutes it will take. Also, please fill out the warranty registration card and return it to us today. This will help us keep you informed of updates to the RISC Router 2600i and future products available from Compatible Systems. You can also register on the web a

  • Compartible Systems Corporation RISC 2600i, 12 Chapter 2 - Getting Started connected to a 10BaseT-compatible twisted-pair hub.  Note: Ethernet cables and cable connectors are not supplied with the RISC Router product. Please contact your reseller or your Compatible Systems representative for information on obtaining the correct Ethernet cabling supplies. Telco Line Connection Requirements The RISC Router 2600i is not a line communications device. In order to connect to a wide area transmission line, you must use a 56K CSU/DSU, ISDN Terminal Adapter, or T1/E1 CSU/DSU. Which of these devices you use depends on the type of telco line you are connecting one of the router’s

  • Compartible Systems Corporation RISC 2600i, 24 Chapter 6 - Basic Configuration Guide Suggested for IPX You may want to set your own network numbers, rather than using the autoconfigured values. You may also want to turn off unused frame types. CV: Use the IPX Routing: Ethernet 0 Dialog Box. TB:Use configure and set keywords in the IPX Ethernet 0 section. WAN Interface PPP Configuration This section covers the settings required for PPP (point-to-point) protocol operation of the RISC Router 2600i WAN interfaces. In general, the parameters listed here should be set for each WAN inter- face on which you plan to use PPP. Note th

  • Compartible Systems Corporation RISC 2600i, Appendix E - Terms and Conditions 41 reasonable control of Compatible Systems, including without limita- tion: inability to obtain necessary materials and components; strikes, labor disturbances, and other unavailability of workers; fire, flood, and other acts of God; war, riot, civil insurrection, and other disturbances; production or engineering difficulties; and governmental regulations, orders, directives, and restrictions. 5. Product Return Policy. Prior to shipping any Product to Compat- ible Systems, the Customer must contact Compatible Systems Tech- nical Support (by letter or telephone) with the following information: (a) reason for return; (b) quantity

  • Compartible Systems Corporation RISC 2600i, Chapter 3 - Network Installation 15 To connect the router to the twisted-pair network, simply plug the twisted-pair cable into the RJ-45 connector on the back of the unit. Connecting a Line Device to the RISC Router 2600i The RISC Router 2600i supports high-speed synchronous operation over the included V.35 cables, or V.11 with a special cable available from Compatible Systems. The RISC Router 2600i independently supports PPP and Frame Relay link protocols on each WAN interface. Connecting Devices to the V.35 Interfaces These

  • Compartible Systems Corporation RISC 2600i, 26 Chapter 6 - Basic Configuration Guide Suggested for Dedicated/Leased Line Operation Dedicated line operation generally does not require additional parame- ters for operation. Required for Dial-On-Demand Operation Incoming dial-on-demand operation requires only slightly more infor- mation than dedicated line setup. Outgoing dial-on-demand requires additional information (see the suggested settings below). • Set dial-up connection • Set PPP connection • Set to allow dial-in and/or dial-out CV: Use the Link Configuration: WAN 0 (and/or other ports) Dialog Box, and select On Demand PPP Link from the Link Type pull-down menu. TB:Use con

  • Chapter 2 - Getting Started 11 What You Will Need To Get Started Before connecting the RISC Router 2600i, please check the list below to make sure that you have received all of the items that are supplied with the RISC Router 2600i package. You should also make sure you have any additional items that are necessary to connect the router to your network. Supplied with the RISC Router 2600i Pl

  • Compartible Systems Corporation RISC 2600i, Chapter 6 - Basic Configuration Guide 31 SMDS Addressing Many of these parameters will be given to you by your service provider. CV: Use Link Configuration : WAN 0 (and/other ports), select SMDS from the Link Type pull-down menu, and click on the SMDS button. TB:Use configure and set the StationAddress, IPMulticast and PollingFrequency keywords in the SMDS WAN 0 (and/or other ports) section. Saving a Configuration File to Flash ROM Once a configuration is complete, you can save it to the router’s Flash ROM. Until saved, all chan

  • Compartible Systems Corporation RISC 2600i, iv Connecting to Thick Ethernet 14 Connecting to Twisted-Pair Ethernet 14 Connecting a Line Device to the RISC Router 2600i 15 Connecting Devices to the V.35 Interfaces 15 Connecting an Out-of-Band Management Console 15 Powering Up the Router 15 Chapter 4 - CompatiView Software Installation 17 CompatiView for Windows 17 System Requirements 17 Installation and Operation 17 Transport Protocols and CompatiView 18 Chapter 5 - Command Line Management 19 Out-of-Band Command Line Management 19 Temporarily Reconfiguring a Host for Command Line Management 19 Setting Up Telnet Operation 20 Chapter 6 - Basic Configuration Guide 2

Related Products and Documents (Network Router):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 CipherLab CP50 G Reference manual cipherlab/cp50-g-47R.pdf 29 Oct 2023 276
2 Smeg ST149 Instruction manual smeg/st149-791.pdf 02 Aug 2022 44
3 Plinius SB-300 Instruction manual plinius/sb-300-591.pdf 14 Oct 2022 19
4 Everpure Single Head EV9272-19 Specification sheet everpure/single-head-ev9272-19-358.pdf 06 Jan 2023 2 0.33 Mb
5 Evolis Dualys Operation & user’s manual evolis/dualys-IXL.pdf 22 Apr 2023 38 1.87 Mb
6 d&b audiotechnik D6 Hardware manual d-b-audiotechnik/d6-67B.pdf 01 Feb 2023 24

Similar Resources:

  • Cisco

    Catalyst 9300 Series

    (132 pages)
    Cisco Catalyst 9300 Series Switches Hardware Installation GuideFirst Published: 2017-06-20Last Modified: 2020-01-31Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 527-0883 …
  • BinTec

    4Ge-LE

    (2 pages)
    123WLANPWRADSLbintec 4-Ge-LEbintec-Router(z. B. RS353j)LANEntfernter StandortZentraleInternetData & PoweroutDatain523441V1.1 - 20150223 - 55300001251 Reset-Taste2 1 x 10/100/1000 Ethernet-Schnittstelle3 Stromanschluss4 Antennenanschlüsse (an den Seiten)5 Schlitz für die SIM-KarteAnschlüsseAuf dem bintec-4Ge-LE wird keine Konfiguration gespeichert, die …
  • Abocom

    ARM904

    (10 pages)
    Multi-Function Wire-less Router Wireless Access Point Broadband Internet Access 4-Port Switching Hub Quick Install Guide L This guide covers only the most common situations. Please refer to the full User Manual on the CD-ROM if your LAN has any of the following: • Router • Existing DHCP Server • PCs using Fixed (Static) IP Addresses M73-APO …
  • Cisco

    7513

    (44 pages)
    INSTALL THE HARDWARECONNECT THE RSPSTART AND CONFIGURE THE SYSTEMINSTALL FIELD REPLACEABLE UNITS (FRUS)1234Quick Start GuideIsCiscodocumentationhelpful?Clickhereorgotohttp://www.cisco.com/warp/public/732/docsurvey/rtg/togiveus your feedback.CISCO 7513 AND 7576 ROUTERS5POWER APOWER BNORMAL …
  • Belkin

    AX3200

    (4 pages)
    Reliable, high-speed performance with simple setupThe AX3200 WiFi 6 router delivers fast speeds to more than 25 devices on your home network. Smooth and stable signals mean everyone can stream, game, and socialize online with plenty of bandwidth—it’s perfect for online learning and working from home. Its sleek, modern design and parental controls make a …
  • Buffalo

    WLA-G54

    (8 pages)
    1®Quick Setup Guide54 Mbps* Wireless Bridge Base Station-gWLA-G54PreparationThis Quick Setup Guide will guide you through quickly and easily installing this product on your Windows PC. For detailed setup and configuration instructions, please refer to the User Manual on the Utility CD or the Buffalo Wireless Support website.Package Contents:◗� …

Comments, Questions and Opinions: